ESD Test Systems
See Also: ESD Test, ESD Simulators
-
Product
Engine Test Systems
Dynas3
-
Dynas3 Machines are specially suited for use in engine test stands. The AC machine, variable frequency drive with test stand controller and safety module are tuned to one another to form a system that has proven itself many times over. It can be used in any type of development and function test stand. The applications range from simple test stands for steady state operation up to sophisticated test stands for dynamic test cycles. Nearly every application in the field of engine testing can be performed on a test stand with DYNAS3.
-
Product
Stress Testing System
Load Dynamix
-
LoadDynamix (former Swifttest) is famous for its IP based converged storage system stress testing, including iSCSI, SMB/CIFS, NFS, FC and HTTP/HTTPS based storage systems. Its GUI interface is very easy to use and allow customer engineer to fully configure all the parameters at the protcol layer. Nearlly all the major IP storage system manufacturers have LoadDynamix products in their test lab.
-
Product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
-
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
Product
Iridium Physical Layer Test Systems
PLTS
-
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
Advanced Test Systems
ATS
-
The commercial version of the RTS-503, this one is not built with the rugged qualifications of the RTS-503. The case is plastic and fuses are used. Otherwise, the internal components and software capabilities are very similar.
-
Product
Manual Flying Probe Test Systems
-
They provide flexible measurement technologies like Kelvin and high voltage tests in combination with low tooling costs. atg Luther & Maelzer offers a wide range of different systems starting from standard systems with 8 heads up to oversized systems with 24 test heads.
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Steering Module Test Systems
-
Steering test systems for quiet evaluation of rattle, NVH & performance issues – non-hydraulic. The MB Dynamics Steering Module Test Simulator family of technologies (SMTS) is an assembly of components and software designed to facilitate the quiet testing, development, troubleshooting, and auditing of a variety of steering gear and steering column assemblies — collectively referred to here as steering modules (including components).
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
Multi-site Module Testing System
TCIII-3200ST
-
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
Product
Software-based Electroacoustic Test System
SoundCheck
-
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences.The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
-
Product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
-
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
Product
IPX3 IPX4 Rain Test System
CX-RIP3/4
-
Shenzhen Chuangxin Instruments Co., Ltd.
For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.
-
Product
Hydraulic Vertical Shock Test System
KRD10 series
-
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Test Automation Platform Deployment System
KS8000A
-
TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments. The Keysight KS8000A Test Automation Platform (TAP) Deployment System provides a lower cost, scaled down alternative to the full KS8400A TAP Developers System without the graphical user interface, results viewer and timing analyzer. Deploy your existing test software and TAP plugins into manufacturing environments using the KS8000A command line interface or your own interfaces.
-
Product
High-Speed Transformer Test System
DU-7211
-
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
Product
Silicon-Microphone 8Ch Auto Test System
BK9015
-
Based on the BK3011 MEMS Mic Tester, the BK9015 is our fully automatic 8 channel MEMS (Silicon) mic sweep tester. Testing up to 8 DUT's simultaneously, the BK9015 can test 8 mics simultaneously and sort them according to passing grade and cause of failure! Because it uses a sweep test, it can check characteristics for the entire frequency range. Your data can be viewed in real time or stored so you can analyze problems or trends.
-
Product
VLF Testing and Diagnostics System
PHG 80 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 80 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltage* Compact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
Test Automation System for Emission Testing
STARS VETS
-
STARS VETS is a Vehicle Emission Test System application available with the STARS Automation platform for chassis, engine and powertrain dynamometers. The application provides test cycle execution, emissions equipment control, results calculation and reporting in compliance with the different legislative standards throughout the global regions. Its flexible design offers a wide range a customization, and it addresses the various requirements for R&D, COP and certification testing.
-
Product
Leak Test System
NorCom 2020
-
The NorCom 2020 batch inspects up to 500 devices per cycle for both gross and ultra-fine leaks. The system incorporates a patented full field interferometer that produces reliable, repeatable leak test results. The system eliminates the need for helium mass spectroscopy or krypton testing for fine, and bubble leak testing for gross leaks.
-
Product
Electrodynamic Vibration Test Systems
A-series
-
A wider range of test requirements and higher test specifications.A-series meets the needs for such a versatile test environment.Advanced automatic energy saving, high level of functionality and a protected test environment.
-
Product
METES - Meter Test Systems
-
Dramatic advances in the field of measurement technology and the use of state-of-the-art micro-electronics have led to the development of a new generation of electricity meters which are far more accurate than their predecessors of just a few years ago. As well as measuring the exact amount of energy used, a high level of integration enables electronic meters to perform a number of additional functions. As a result, these meters are also more sensitive to network irregularities. This means that regular testing is the only way to ensure that a meter functions correctly, both during final factory tests and during the entire life span of a meter.
-
Product
Electromagnetic Vibration Testing Systems
EV series
-
Labtone Test Equipment Co., LTD
EV series of electromagnetic vibration testing systems cover a wide range of forces ideal for many different applications. The electrodynamic shaker systems are well-suited for vibration testing products and structures of any size – from small components and electronic hardware to very large devices and structures.
-
Product
Automatic Hysteresis Graph Test System
DX-4DMT
-
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
Product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
-
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Product
Integration of Inline Test Systems
-
The test system and adapter can also be integrated in inline test systems. Additional communication can take place via interfaces (e.g. RS232, DLL). We have already created numerous integrations for different manufacturers.
-
Product
ESD Test Simulator
ONYX16
-
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
