Ultrasonic Thickness Gauges
-
Product
High Voltage Thick Film Chip Resistors
HVTK (HVR)
-
*Highly reliable multilayer electrode construction*Higher component and equipment reliability*Excellent performance at high voltage*Reduced size of final equipment
-
Product
Modular Bluetooth Tide Gauge System
TideM8
-
The TideM8 is a black box instrument designed around the same 'winstrument' specification as used in the popular SonarMite portable echo sounder, this design criteria specifies that all display and interactive communications with the instrument use Bluetooth radio technology to communicate with a PC or PDA device. Through extensive experience of tide gauge installation and manufacture the TideM8 design is modular with separate radios, gauge, display and power supply units. This modular design enables the user to configure every combination from a simple gauge and PDA to a gauge and remote display using radio telemetry communications.
-
Product
Measurement System of Ultrasonic Vocalizations (USV)
SONOTRACK®
-
Sonotrack is the only recording system which is designed for laboratory use and high-throughput analysis of USV. It records the full spectrum of ultrasonic vocalizations from 15 kHz to 125 kHz without limitations for the "recording duration". The ultralow-noise amplifiers and highly sensitive microphones provide unrivalled quality of the recorded signals.
-
Product
SENSOR FOR THICK & CURVED MATERIALS
S3
-
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
-
Product
XP2i Digital Pressure Gauge
-
AMETEK Sensors, Test & Calibration
We provide some of the world’s most popular XP2i digital test gauges for a variety of applications and markets. Included are intrinsically safe "percent of reading" gauges, process gauges, differential pressure gauges, panel mounted gauges, and gauges specifically designed for use in the maritime industry. Whether you’re looking for a gauge with long battery life to mount in hard to reach locations, a gauge to collect and store readings in the field in extreme conditions, or one that doesn’t require recalibration for up to three years, we have the perfect gauge for you.
-
Product
Ultrasonic Transducers
-
Low frequency transducers for ultrasonic testing of concrete and other course grained materials. Shear Wave transducers (pictured above) are used in combination with compressional wave transducers to calculate Poisson's Ratio. The line of general-purpose compressional wave transducers feature robust PZT elements in stainless steel.
-
-
Product
Thickness Measurement Testing
DRK3011B
-
Shandong Drick Instruments Co., Ltd.
It is used for the durability test of children's mattress surface rolling and the test of the height of the cushion surface.
-
Product
Layer Thickness Meter
CHY 113
-
It is usded to measure the thickness of metallic coatings (eg paint) only on substrates with ferromagnetic alloys (eg steel). The meter is designed to provide easy operation in one hand.
-
Product
Spline Gauging
XT Splines
-
Popular 2 point spline heads held in stock include:• 20–25mm over 2mm pins• 20–25mm over 2.032mm pins• 24–29mm over 2mm pins• 24–29mm over 2.032mm pins• 25–35mm over 2mm pins• 25–35mm over 2.032mm pinsEach of these application heads can be fitted directly to our Bluetooth XT range of internal micrometers in seconds for fast, efficient use with incredibly accurate results that can be digitally recorded.
-
Product
Integrated/Separated Explosion-Proof Ultrasonic Level Gauge
HR9100E
-
HighReach Measuring & Controlling System Co.,Ltd
1. Safety / use of die-cast aluminum alloy waterproof, explosion-proof shell; the explosion-proof grade of the instrument reaches Exd (ia) IIBT4 2. stable and reliable / we choose high-quality module key components from the power supply Part of The Circuit Design Stable and Reliable Devices CAN Completely Replace imported Instruments. 3. Patented Technology / Ultrasonic Intelligent Software CAN with Carry OUT Intelligent echo Analysis, the without the any the debugging and OTHER Special Steps, the this Technology has The function of Dynamic Thinking, Dynamic Analysis 4. High precision / sound wave intelligent patent technology owned by our company, so that The accuracy of the ultrasonic level gauge is greatly improved, the liquid level accuracy reaches 0.3%, it can resist various interference waves, the failure rate is low, the installation is easy, and the maintenance is easy. The instrument is a non-contact instrument and does not directly contact with liquid. Users can use this manual to calibrate the instrument. 6. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
Product
PING))) Ultrasonic Sensor + Protector Stand
910-28015B
-
The PING))) Ultrasonic Distance Sensor is perfect for any number of applications that require you to perform measurements between moving or stationary objects. The sensor measures distance using sonar; an ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the echo return. Output from the PING))) sensor is a variable-width pulse that corresponds to the distance to the target.The protector stand was designed to help fortify the PING))) sensor against collision damage, and to provide a more stylish appearance in doing so. The stand is cut from high-grade aluminum and can be attached to your projects easily.
-
Product
Ultrasonic Corona & Arcing Detector
ULD-40™
-
The ULD-40™ is an ultrasonic detector designed for corona effect and arcing detection for predictive maintenance in electric utilities. Available with a variety of accessories, this instrument is a cost-effective must for any prevention plan.
-
Product
Ultrasonic Integrated Field Recorder
iFR-IV
-
Binary Acoustic Technology LLC
If you are looking for professional quality bat detection and ultrasonic recording gear, consider the BAT approach. We offer a complete solution. Binary Acoustic Technology offers a line of Ultrasonic Receivers along with spectral analysis, bat detection and hard-disk recording software. Combine one of our receivers, with our SPECT'R Mobile software and an ultra-mobile computer to form a complete ultrasonic detection and recording solution.
-
Product
Low Gauge Vacuum Tester
G4103
-
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Vacuum Sensor, Thermocouple Vacuum Gauge for High Vacuum
DV-5 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.
-
Product
Pressure Gauges
-
Diaphragm pressure gauges feature stainless steel construction for superior chemical and corrosion resistance for your intermediate pressure measurement applications. Because of the protective diaphragm seal design, these pressure gauges are ideal for use with viscous as well as corrosive fluids. Optionally, these diaphragm pressure gauges may be ordered with glycerine filling to help dampen the effects of machine vibration and pulsation of the media.
-
Product
Analog Pressure Gauges
-
AMETEK Sensors, Test & Calibration
Our corporate partner, US Gauge, provides some of the world’s most popular analog pressure gauges for a variety of applications and markets. Included are process gauges, liquid filled gauges, test gauges, and general application gauges.
-
Product
Non Rotating Spindle Type Tooth Thickness Micrometer
-
Measures the "root tangent length" of gears. Compatible modules differ depending on the model.
-
Product
Ultrasonic Exhaust Flow Meter for Real-time Measurement of Vehicle/Engine Exhaust Flow
EXFM-ONE
-
EXFM-ONE employs an ultrasonic method for measuring exhaust gas flow rates directly from a vehicle or engine. The unit can be used for various applications such as real time mass measurement of raw exhaust gas combined with MEXA-ONE (Motor Exhaust Gas Analyzer), or for Particulate Matter/emission measurement combined with partial flow dilution system such as MDLT (Partial Flow Dilution Tunnel) or BMD (Bag Mini Diluter). Fuel consumption evaluation is also available when EXFM-ONE is paired with an optional air-to-fuel ratio (AFR) analyzer.
-
Product
Semiconductor Technology, Micro Scriber + Flatness, Bow, Warp, Curvature, Glass Thickness
FLATSCAN
-
Optik Elektronik Gerätetechnik GmbH
Non contact automated 2D- or 3D measurement of warp, bow, slope and surface curvature with software module for calculation of thin film stress (wafer stress) of wafers and glass substrates.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Coating Thickness Meter
SI-1098
-
Coating Thickness Gauge SI 1098 is a highly intelligent and precise instrument used to quickly and accurately measure thickness of coating or plating on almost all kinds of metal surface. Technology – Magnetic Induction – (enables measurement of non magnetic coatings on magnetic substrates such as Steel, Mild Steel, Cast Iron &Magnetic Stainless Steel). Example coatings:- Paint,Zinc / Galvanising, Chrome, Copper, Enamel, Rubber, Paint, Varnish, Powder Coating, Plastic etc.
-
Product
Contactless One-Point Wafer Thickness Gauge
MX 30x
-
The MX30x series are manual one-point Thickness gauges for silicon wafers.
-
Product
Digital Gauge Pressure
ZET 7012-I VER.2
-
ZET 7012-I VER.2 digital gauge pressure (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.
-
Product
Coating Thickness Meter
SI-1101
-
Coating Thickness Gauge SI 1101 is a highly intelligent and precise instrument used to quickly and accurately measure thickness of coating or plating on almost all kinds of metal surface. It not only indicates thickness of coating or plating but also automatically identifies the base material. It is applicable to measure non-magnetic painting, ceramic, enamel, plastic, rubber coating on magnetic base materials such as iron and steel , non- ferrous metal plating such as nickel & chromium, anticorrosive coating, non- conductive painting, plastic coating and anodic oxide film on non-magnetic conductive devices .
-
Product
Thickness Gauges
CMX
-
The CMX has all features of the MX & MMX gauges with a ton of advanced features. Measure material and coating thickness simultaneously, while still detecting pits & flaws in a single mode (PECT). Auto probe zero, auto probe recognition, auto temperature compensation are also included. Selectable Large Digits and B-Scan display options, up to 64 custom user definable setups, selectable transducer table for precision linearity, and material and coating calibration options are also available.
-
Product
Bore Gauges Xtreme 3 Holematic Smart
-
Digital bore gauge with integrated Bluetooth® technology – pistol type with quick retraction handle.
-
Product
Thick Film Inspection
785
-
For thicker coatings such as coal tars, extruded and tape coatings, the Model 785 has a range of infinite voltage settings from 1,000 to 15,000 volts.
