Meters
sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.
See Also: Sensors, Measurement
-
Product
Turbine Flow Meters
CT15
-
Flows up to 15 lpm (4 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-esters
-
Product
Noise Figure Meters
H5M Series
-
*Frequency range from 10 MHz to 4/20 GHz*Noise Ratio and Gain measurements*Frequency converter measurements with a fixed or external heterodines*Built-in thermostatic YIG preselector*High measurement speed*Extend the NFA solution up to 50 GHz with special downconverter unit*SCPI Language Compatibility
-
Product
Color Matching Booth
-
GSM Round Cutter is used to test material grams per square meter. It would cut sample to 100cm2 cutter, depth max 5mm. Normally, GSM cutter is suitable to cut textile fabric, leather, paper and etc. It has four double-sided blades, and the blade is evenly distributed in four equal parts. The blade can be replaced. GSM Testing is essential for some tests like Matindale abraison test meet standard ISO20344.
-
Product
Paper Testing Instruments
-
Whiteness and chromaciticity tester, whiteness meter, tensile stiffness tester, automatic horizontal tensile tester, automatic horizontal tensile tester, vertical tensile tester, pulp beating (refining) freeness tester, water absorbtion tester, Cobb tester, COBB sample cutter, coefficient of friction tester, electronic bending stiffness tester, paper and cardboard thickness meter, paper and cardboard thickness meter, ink rubber tester, standard strip cutter, softness tester, carton compression tester, paper air permeability tester, internal ply bond tester, puncture strength tester, paper tearing tester, electronic tearing tester, mullen burst tester, crush tester, Bekk smoothness tester, folding endurance tester
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Clamp Meters
-
Basic functions:AC current: 40/400/1000ADC current: 40/400/1000AAC voltage: 4/40/400/750VDC voltage: 400mV/4/40/400/1000VResistor: 400/4/40/400K/4/40MTemperature: -20 to +750°CFrequency: 10/100/1000Hz/10/100kHz/10MHzDuty cycle: 0.1 to 99.9%Capacitance: 5nF/50nF/500nF/5μF/50μF/200μFSpecial functions:Auto rangingNCVDiodeContinuity buzzerLow battery displayData holdRelative data holdAuto/manual range shiftZeroAuto power-offOverload protectionSampling frequency: 3 times/sMaximum display: 3999Maximum open distance of clamp mouth: 55mmGeneral characteristics:Color: iron gray and orangeNet weight: approximately 274gLCD size: 46 x 32mmSize: 245 x 90 x 33mmPower: 1 x 9V and 6F22Packing content:CartonHandheld bagEnglish manualTesting leadBatteryTemperature probe
-
Product
Smart Polyglot - Wireless Probe
-
Signals & Systems India Private Limited
Smart Polyglot is designed to talk to meters of all protocols – PACT, ANSI, IEC. Not only does it talk over optical media, it interfaces with IR, IrDA meters as well, making it the only device that talks to any type of meter in any language.The Smart Polyglot has a wireless Bluetooth interface and enables seamless use with any DOS, Android, or Windows based devices with Bluetooth support. This Smart Polyglot Bluetooth probe can detect the commands from Bluetooth connected devices and establish a connection automatically for meter reading applications.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 44 GHz
N9961B
-
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Underwater Thickness Meter
Multigauge 3000
-
Large bright 10mm display. Integral battery with 55 hours runtime. Can be easily upgraded to a topside repeater. 500m depth rating.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
Vibration Meter
-
The Vibration Meter is a multi-functional device designed for machine vibration measurement (cyclic condition monitoring and troubleshooting), production line quality control, as well as structural vibration assessment.
-
Product
Light and Energy Meter
Model 656
-
OAI Model 656 Meter is designed for use with all mask aligners and flood exposure systems. For over 45 years, OAI is a world leader in UV Light & Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries.
-
Product
Online Vibrometer
MK-64
-
Online vibrometer that accurately detects equipment abnormalities. Higher visibility with the new digital meter
-
Product
Professional Floor Certification Kit
PFC-252
-
The PFC-252 includes Prostat's PRS-812 Resistance System Set with modified 5 pound conductive rubber electrodes and Prostat’s Cable Spacers for exact measurements. The PRS-812 wide range resistance system can take measurements at 10 and 100 volts with accuracy within ±5%. Also included is the PFK-100 Field Meter Set. The PFK-100 set includes Prostat's unique PFM-711A dual range field meter, CPM-720A charged plate monitor assembly and PCS-730 ±1 kv charging source. With this instrument set you can measure electrostatic fields, analyze ionizer performance and assess the voltage generation of materials, equipment and personnel.
-
Product
Digital Panel Meter
MW(Q)-5A
-
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth.
-
Product
Benchtop DO/BOD Meter
LAQUA DO2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Precision Laser Distance Meter with Clinometer
TRUPULSE 200X
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LED Display*Range to non-reflecting targets 1.900m*Range to reflecting targets 2.500m*Accuracy in range ± 4cm (± 30cm to weak targets; shown in display)*Accuracy in slope ± 0,1°*RS 232/Serial interface and bluetooth (iOS compatible)*IP protection IP56
-
Product
Impedance Analyzer
MFIA
-
The Zurich Instruments MFIA is a digital impedance analyzer and precision LCR meter that sets the new standard for impedance measurements in the frequency range from DC to 5 MHz. The MFIA provides 0.05% basic accuracy and a measurement range spanning from 1 m to 10 G. The instrument has a high measurement repeatability and a small temperature drift. With the LabOne user interface the MFIA offers a number of long-awaited innovations for the impedance and LCR measurement available without the need of any software installation.
-
Product
Laser Range Finder
-
Shenzhen Noyafa Electronic CO.,LTD
For more than a decade Noyafa has been engaged in researching, developing, and producing high-quality, affordable laser distance meters & rangefinders. Its laser measurer products offer higher accuracy, better target acquisition and higher range resolution. Their capabilities go far beyond just measuring a range. You can instantly measure slope distance, inclination and azimuth and calculate horizontal and vertical distance - all with a single push of a button.
-
Product
Pressure Meter
ZET 7112-A VER.2
-
The ZET 7112-A VER.2 pressure meter is intended for use in automated process control systems for various industrial applications:
-
Product
Portable Moisture Analyzer
PPMa
-
Multifunctional Multi-Purpose Cost Effective, Menu-driven, intuitive, easy-to-use, Handheld Dew Point Meter, Hygrometer
-
Product
Anemometers
-
Sper Scientific offers a wide selection of anemometers for directly measuring wind and air velocity. They will tell you all you need to know about the speed of the wind, the temperature, even humidity and heat stress information. The extraordinary range of uses that our meters provide have made them required equipment in a wide range of professional settings. Firefighters, farmers, HVAC technicians and military personnel all over the world use these meters to gather accurate, real-time data.
-
Product
Insulation Resistance Meter
AMIC-10
-
The AMIC-10 digital insulation resistance meter is used for direct measurements of the insulation resistance of electrical equipment working with voltage up to 1 kV. In addition, this meter makes it possible to measure compensation and protective connections, low-voltage resistance measurements and DC and AC voltage measurements.
-
Product
Power Meters
-
Chroma Systems Solutions, Inc.
Designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products.
-
Product
True RMS Multimeter w/ Temperature and Capacitance
DM393
-
UEi Test & Measurement Instruments
The DM393 is one of our safest Industrial Duty meters ever made. All inputs, ranges and functions protected to CATIII 1000 Volts. Perfect for HVAC and electrical technicians whose applications require higher accuracy measurements and True RMS precision. Built-in temperature means one less instrument to bring to the job. The DM393 has convenient access to battery and fuses without breaking calibration seals
-
Product
Temperature and Process Controllers
-
The ATR121 Temperature Controller is a 3 digit display PID controller with up to 2 relay outputs, Solid State Output and an option to be a Modbus RS485 Slave device.The ATR141 Temperature Controller is a 4 digit PID controller and Panel Meter which can display up to 3200°F with an S Type Thermocouple. The ATR141 can have up to 2 relays, a Solid State Output and an option to have a Modbus RS485 output.
-
Product
Meter with "3-in-1" pH/Temperature Combi Electrode
pH 6+
-
Multi-Point Calibration (up to 3 points) with Auto-Buffer Recognition - choice of USA, NIST or pure water buffer standards with ±0.01 pH accuracy
-
Product
Torque Metering System
-
Measure and record torque for rotating machinery, test stands and ship board applications. Riverhawk Torque Meter Systems are capable of retrofitting to existing couplings and shafts with minimal modification.
-
Product
4 2/3 Digital Potentiometer Meter
CS2-PM
-
CS2-PM Potentiometer Indicator has been designed with high accuracy measurement, display and communication of Ohm (3 wire) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.
-
Product
Level Meter
LM86
-
Beijing Airport Beiguang Instruments Co., Ltd
The basic version magnetic level gauge.
