Filter Results By:
Products
Applications
Manufacturers
-
product
PH Meter / Tester, 0pH to 14pH, 0.01, 0.2, 400 ms, 0 °C, 50 °C
72-6783
The 72-6783 is a 0 to 14pH Meter with 12.5mm LCD display. Any combination of pH electrode and male BNC connector can be used. pH meter included with battery.
-
-
product
pH / mV Transmitter
DO9403T-R1
The DO9403T-R1 pH transmitter converts the output of a pH electrode, with temperature compensation, into a 4÷20 mA signal.
-
product
Handheld Water Quality Meters
LAQUA PC210
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
product
Voltage Calibrators
Practical Instrument Electronics, Inc.
PIE has a voltage calibrator to fit your needs from the PIE 235 voltage and pH simulator to the advanced troubleshooting capabilities of the PIE 532 milliamp and voltage calibrator. The PIE 532 includes our patented Loop Diagnostic Technology! All the voltage/milliamp calibrators have fuse-less protection, rugged design and long battery life. With the PIE 535, source 4 to 20 milliamps or 10 to 50 milliamps into loop instruments and drive final control elements such as valves and actuators with up to 42 volts.
-
product
pH & ORP Sensors
The Barben Analytical Performance Series products are 3rd generation combination pH/ORP electrodes targeted at harsh, industrial measurement applications. High pressures, strong chemicals, and elevated temperatures typically shorten the lifespan of conventional double-junction pH probes. In these applications the Performance Series sensor offers extended sensor lifespan, as well as decreased drift, and longer calibration intervals. Each sensor is manufactured with our patented Axial Ion Path® reference technology, proprietary Low-Noise & High-Temp Signal Cable along with proprietary ruggedized, high temp and coat resistant glass formulations. A wide selection of sensor body styles and process fittings in a variety of corrosion resistant materials allow direct replacement of short-lived OEM pH/ORP sensors. Barben Performance Series sensors are compatible with all major manufacturers of pH analyzers and transmitters. Upgrade your analytical measurement without the hassle and expense of replacing costly field instruments.
-
product
pHTestr® 50 Waterproof Pocket pH Tester,
The Oakton pHTestr 50 has a replaceable double junction sensor for longer life, an expanded number of applications, and easy maintenance. Double-junction electrode sensor handles wastewater and solutions containing sulfides, heavy metals, and TRIS. Electrode sensor offers a clog-resistant Kynar® junction and a recessed, glass pH bulb to protect against breakage. Valox sensor housing resists most chemicals. The keypad clicks to confirm operation, and allows access to a variety of functions. Calibrate up to three pH points with the auto-buffer recognition at both USA and NIST standard buffers. Additional features include an automatic temperature compensation (ATC), hold function, auto-off function, self-diagnostic error messages, and a three-segment battery-life indicator.
-
product
MRI POWER SUPPLIES
MRI Series
Input: 208 VAC ± 5 %, 3 PH, 60 Hz Output: 120 VDC fixed, 20 Amps Power: 2.4 KW Ripple: 5 % Enclosure: NEMA 1(20″ H x 16″ W x 9″ D) Weight: 125 lbs
-
product
PH Meters
* Three reading modes* Smart-Read function. More stable the reading with auto recognition end-point* Cont-Read function. It is clear to read the sample changing in measurement process* Timed-Read function. Auto timed to store the reading* Auto upgrade hardware* Power-off protection, protect your data* Remind the electrode performance and calibration.
-
product
Bluetooth® Enabled PH And Temperature Pen
UltrapenX2™ PTBT2
*Accuracy of ± 0.01 pH*1, 2 and 3 Point Calibration*Automatic Temperature Compensation*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated Electronics*Powered by One N Type battery (Included)*Waterproof
-
product
Water Quality Transmitters
Omga's Water Quality Transmitters are multi-variable loop powered transmitters that can be configured for use with pH, ORP, Conductivity, or Flow sensors and can be wall, pipe, or pannel mounted
-
product
pH Sensors
Campbell Scientific pH sensors measure the level of pH in sample solutions by measuring the activity of the hydrogen ions in the solutions. This activity is compared to pure water (a neutral solution) using a pH scale of 0 to 14 to determine the acidity or alkalinity of the sample solutions.
-
product
ION 100 Portable Ion Meter
The new addition to the Environmental Express Oakton product line features updates to measuring water quality easier and faster. The larger LCD display is 2.75 in. by 2.0 in. for a better viewing angle, and has indicators for battery life, stability, and calibration. The ION 100 meter measures pH, mV, ion concentration of 16 commonly measured ions, and temperature. The microprocessor-based meter features automatic calibration, automatic temperature compensation, function setup, self-diagnostics, automatic power-off, and low voltage display. The meter uses advanced digital processing technology, intelligently improving the response time and accuracy of your measurements. Easily switch units among pX, mol/L, and mg/L (ppm).
-
product
Ion/pH/mV Meter with Single Junction pH Electrode
Ion 6+
Direct Ion Concentration for use with most mono- or di-valent Ion Selective Electrodes (ISE) :: mV measurement mode allows you to check performance and calibration of your ISE
-
product
Pen-type PH Meters
Pen type PH meter, is designed for on site or field operation. The PH value and temperature value at the same time are displayed .The instrument is suitable for tap water monitoring, aquaculture, environmental protection, printing and dyeing, electroplating, chemical, metallurgical, pharmaceutical, biochemical, food, and water treatment industries and scientific research units for the determination of water PH value
-
product
pH Meters
pH meters are used to measure the acidity and alkalinity of liquid or semi-solid samples across many industries, this device has ORP measurement that is widely used in aqueous samples such as oil emulsions, unclean water it is majorly applied in waste water, drinking water, food and beverage, chemical and pharmaceutical testing.
-
product
5000 AMP DC Rectifier - Air Cooled, P/N 6037C1
Air Cooled SCR Controlled Power Supply, 50 KW, P/N 6037C1Input: 480 VAC, 60 Amps, 3 PH, 60 HzOutput: 6 to 10 VDC, 5000 Amps maxContactor and overload relay are installed for protectionStart / Stop capabilityEPO capabilityManual voltage control and current limitOutput voltage and current are displayed on the voltmeter and ammeterIndoor enclosure, 68″H x 65″W x 36″DAll input/output connections are inside the enclosuresEstimated weight: 1000 lbs.
-
product
MAX Waterproof 4-in-1 pH / EC / TDS/Temp Tester
MW804
The Milwaukee MW804 MAX Waterproof 4-in-1 pH/EC/TDS/Temp Tester is designed as an all-in-one solution for growers.
-
product
Repair of Solid State Switch, P/N 60-SS480
Solid State Switch P/N 60-SS480Input: 480 VAC, 3PH, 60 HzOutput:480 VAC, 3 PH, 60 HzControl Voltage: 120 VAC, 1 PH, 60 Hz
-
product
Process Sensors
Knick Elektronische Messgeräte GmbH & Co. KG.
pH, ORP, conductivity and dissolved oxygen sensors for industrial applications. Analog and digital Memosens. Low-maintenance, high-precision measurements in chemical, pharmaceutical, food, energy and the environment.
-
product
Industrial pH Meter (Four-Wire Analyzer)
HP-200-K
One-touch calibration function Realizes gentle measurement by combination with lead-free ORP electrode
-
product
pH or mV Configurable Transmitters
DO9785T
pH or mV transmitter, completely configurable, for panel mounting
-
product
pH 620 Waterproof Meters
These waterproof handheld meters feature a –2.00 to 20.00 pH range with 0.001 pH resolution. Combined with accuracies up to ±0.002 pH, these meters provide a new benchmark in our pH meter line. Store up to 500 data sets in the meter‘s memory. Time-and-date stamping meets Good Laboratory Practice (GLP) standards.The pH 620 meters offer the latest in pH calibration capabilities including up to six calibration points, a user-settable “calibration due” alarm, and up to 15 buffer options with auto-buffer recognition of USA, NIST, DIN, and PWB standards. The infrared (IrDA) wireless technology makes PC downloading more convenient and easier. Dual powerup allows you to use batteries while out in the field or the optional AC power adapter while in the lab.As always, our waterproof meters are IP67 rated for protection against both dust and water, even with no probes attached.
-
product
PH / ORP Monitor / Controllers
720 Series II
The advanced “isolated” circuitry of the 720 Series II pH/ORP Monitor/ controllers guarantees accurate and reliable measurements — completely eliminating ground-loop and noise issues. The unique sensor preamp allows for longer distances between the sensor and the Monitor/controller without the loss of accuracy or reliability.
-
product
PH Meter
VAT1013
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
PH meter high accuracy , pocket size, pH &temperature double display,Replaced pH sensor.
-
product
Active Switching Rectifiers, 2 KW, P/N 6016C
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
product
Nutrient | Oxygen | PH Sensors: PH Sensors
pH (potential Hydrogen) is a measurement of the level of acids and bases in water. Our pH sensors have been used extensively to research ocean acidification, coral reefs, coastal marine biology, and to conduct environmental monitoring.
-
product
Universal Transmitter
Model LXT-330
Teledyne Analytical Instruments
Model LXT330 Liquid Transmitter is a single or dual channel, universal, multi-parameter transmitter, designed for continuous online liquid measurements. It is paired with SP3 Smart sensors and is intended for use in non-hazardous, general purpose rated industrial environments. The SP3 sensor platform covers a wide range of liquid analytical measurements, such as pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity, resistivity and turbidity. The LXT330 transmitter can be used with any SP3 smart sensors without additional user reconfiguration. The Universal Transmitter & Smart Sensor loop philosophy removed the need to stock for multiple instrument types. The process parameter, sensor details, serial number and calibration history are stored in the sensor's main memory, facilitated by two-way digital communication between the sensors and transmitter. The LXT330 universal transmitter allows for up to two SP3 sensors per transmitter (contact factory for available combinations).
-
product
Meter With pH Electrode, Conductivity Probe
PC 2700
Your all-in-one solution for multi-parameter research work in the lab! The new PC 2700 is accurate, reliable and intuitive with user-friendly functions. Meter comes with a multi-data screen that includes Temperature, electrode status, calibration points, date and time along with your desired measurement parameter
-
product
Benchtop Multi-Parameter Water Quality Meters
Labodam benchtop multi-parameter water quality meters come with different measurement modes for quality and testing of water on different parameters such as pH, conductivity, TDS, salinity, and resistivity content from the test sample.
