Filter Results By:
Products
Applications
Manufacturers
-
product
GPS/FMS Universal Test Fixture
TA-3000
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
product
Mobile Handset Voice Quality Test System
BK9024
If you need to test cellphones, the BaKo Type BK9024 is fast and switches between up to 8 phone chambers at once, making it a great choice for quality control on your production line.
-
product
10A DIGITAL MICRO-OHMMETER
MPK-2000e
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
PXI Automotive Switch Simulator Modules
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Synchro Simulator
SPA-CASE
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
product
PXIe-4144, 4-Channel, ±6 V, 500 mA PXI Source Measure Unit
782432-01
PXIe, 4-Channel, ±6 V, 500 mA PXI Source Measure Unit - The PXIe-4144 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4144 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Turn-Key Short Circuit Laboratories
For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test
-
product
Radio Frequency (RF) And Microwave Products
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
product
PXI 12x8 RF Matrix 300MHz 50 SMB
40-726A-511
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Test Switches and Accessories
FT Flexitest Family
The ABB FT test kit comes with a convenient carrying case to hold your hand held meter, test plugs patch cords, clips, and test probes in neat order. Patch cords are highly durable and flexible. Test switch accessories include: Test plugs Test kits Covers Interlocking bars Miscellaneous
-
product
PXI RF Multiplexer Switch Module
PXI RF Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI RF Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Software
TOELLNER-wavecontrol
Toellner Electronic Instrumente GmbH
The Software TOELLNER-WaveControl provides waveforms and controls the TOELLNER system components at the test station, which can be individually tailored to your requirements. Using a DAQ-Card, any signal waveform can be provided with Arbitrary Power Supplies or 4-Quadrant Amplifiers with outputs from 160 W to 5200 W. For fast interruptions, TOELLNER offers electronic switches with switching times below 500 ns.
-
product
Flight Test Switches
Curtiss-Wright Defense Solutions
Our compact, deterministic flight test switches have been qualified to reliably deliver high-speed, real-time data with a wide temperature operation ranging from -40 to 85°C. Their rapid boot-up capability minimizes data loss from power outages, while their flexible forwarding and filtering configurations can send what is required to multiple destinations for real-time monitoring, recording, and transmission.
-
product
Decades
PeakTech Prüf- und Messtechnik GmbH
For production testing, teaching aids, research and development. You can set all resistance values between 1Ω to 11.111 MΩ with high precision in 1Ω steps to get the desired value quickly and user-friendly. The angled plastic housing ensures a clear arrangement of the rotary switches, whereby the test leads are connected via 4mm safety sockets.
-
product
6U High-Density PXI RF Matrices
Pickering's 6U high-density matrices are suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture - this maximizes isolation and RF performance.
-
product
General Purpose Switches
SMX-5XXX (General Purpose)
The VTI SMX-5xxx Series of general purpose switches deliver exceptional performance and reliability by implementing extensive signal path shielding, isolation and built-in health monitoring. Embedded virtual schematic control simplifies setup and debugging, allowing all relays to be engaged independent of application software and device drivers.Ideally suited for a wide range of discrete signal switching, the SMX-5xxx Series provides uncompromised measurement integrity ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
product
Lifecycle Test System
Model 933
The Model 933A Life Cycle Test System is a low cost, generic test platform used to perform cycling of keypads, keyboards, membranes, switches, or any product requiring fatigue testing.
-
product
Becker Transponder Test Fixture
TA-3400
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
product
Surface Mount Switches
Dow-Key® Microwave offers PCB mounted, miniature electro-mechanical microwave switches. These switches are designed with an overall size of 0.75” x 0.75” x 0.58” and weight of 0.5 ounces for test and aerospace applications where small size, reduced weight, and less power consumption are critical.
-
product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
PXI High Density Multiplexer: 99-ch, 2-Wire, 100Vrms/1A, Armature Relays
M9103A
The M9103A, a high-density, high-power 99-channel multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time, or multiple channels can simultaneously connect if needed. This module is ideal for routing multiple analog signals to a measurement device in an automated test environment (ATE) or data acquisition systems. Each channel switch has a high and low for 2-wire switching. The high-quality armature relays are capable of switching up to 100Vrms, with up to 60W of power. Choose from the durable connector block or standard cable connections.
-
product
Automated Optical Switch - MATRIQ
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Test Switches
RTS
STATES Type RTS Test Switches are designed to simplify and speed testing and check-out of relay, control and instrumentation systems. They eliminate the need to change connections and prevent open-circuiting CTs during tests.
-
product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
