Filter Results By:
Products
Applications
Manufacturers
Test Software
programs, procedures or rules and associated documentation pertaining to the operation of a computerized test set.
See Also: Test Software Development, Software Testing
-
product
DR software, for use with CT100 Series TDRs
CT Viewer™
CT Viewer™ is a full-featured TDR waveform analysis software package for Microsoft® Windows® XP / Vista PCs that lets you archive, manipulate, analyze, and compare TDR data acquired with CT100 Series Automated Metallic TDRs or any other TDR instrument, now with live internet streaming and remote control of CT100 Series TDRs. CT Viewer™ is included with CT100 Series TDRs. Read on to discover how CT Viewer™ will change the way you test cables.
-
product
DC Electronic Load Control Software
EES-100-xx
EES-100 Software controls all electronic load types. ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing
-
product
Battery Test Equipment
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
product
100 Pin Breakout Interface
VSI-Breakout-100
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Adapter/Charger ATS
8020
Chroma 8020 has standard test items specially customized and optimized for the features of Adapter and Charger that provides excellent test performance to meet the requirements of mass production. Meanwhile, the software equipped is very friendly and easy to operate that is suitable for production line use.
-
product
LinkExpert Software
LinkExpert enables complete control and management of Teledyne LeCroy's family of Protocol Analyzer and Exerciser hardware. LinkExpert provides a convenient interface to run Compliance, Conformance and Validation tests on PCI Express (PCIe) and SAS (Serial Attached SCSI) links. The LinkExpert software interface is provided free of charge and includes as standard, several validation tests for PCIe Hosts (Root Complexes) and Devices (End Points).
-
product
Violett for Avnu Test Tools
To meet the needs of members and support in-house testing needs, the UNH-IOL has developed custom software test tools and automation frameworks. The Violett® for Avnu Test Packages listed below enable our customers to be better prepared for certification testing by running in your own labs the same software UNH-IOL technicians will use to test your product for certification.
-
product
Modbus Test & Simulation Software
ModBus Constructor 1.7
Using Modbus Constructor you can quickly create a data management model for any of your Modbus devices. Unlike other available solutions on the market which provide displaying data as columns of abstract numbers of the same type, Modbus Constructor represents each data element exactly as you need. You may define type, format or scale independently. This makes them easy to read and analyze.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Emissions Dynamometers
MD-100-CM-2WD
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2020 we estimate that our equipment will have performed nearly 1 billion vehicle tests. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands.
-
product
Automated Measurement Expert (AMX), VNA Plugin
S94702A
The Keysight automated measurement expert (AMX) is a smart software solution for automated multiport S-parameter measurements with the PXIe vector network analyzers M937xA/M9485A or the benchtop E5080A ENA network analyzer. The S94702A AMX VNA plugin adds S-parameter measurement capabilities to the Keysight test automation platform (TAP). The combination of the TAP and the VNA plugin forms the AMX backend software, which makes the VNA setups and executes the test sequences in the PXIe controller according to the optimized test sequence files generated by the AMX test plan builder. Other instrument plugins allow you to control the DUT mode, expand the number of test ports with the PXI switches or multiport test set, and use external instruments such as a DC power supply and a digital multimeter. The AMX backend software also provides step-by-step calibration wizard for full multiport calibration using the 4-port ECal module.
-
product
Test Universe
Test Universe is OMICRON's comprehensive and easy-to-use testing software for the CMC device family. It allows you to combine a wealth of application-optimized test modules for creating flexible and fully automated test plans that provide you with an enormous range of functions.
-
product
Digital Closed Loop Control Thermal and Mechanical Testing System
3800 System
The Gleeble 3800 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data from thermal-mechanical tests and physical simulation programs.The result is a system unequaled for physical simulation and thermal-mechanical materials testing.
-
product
VNAs for Automated Test Equipment (ATE)
With our USB VNAs your automated test equipment works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
-
product
Functional Testing
Functional testing is a pivotal element for strengthening the quality of developed software. Functional testing basically refers to the black box testing that evaluate a particular IT product with reference to the functional requirements indicated with its specification. Functional test analysis process involves the testing activities which measure the code of each component to assure quality.
-
product
Semiconductor Test
Ismeca NY20
20-position turret platform for semiconductor test, inspection and packaging, provides the highest quality yield and throughput. It integrates innovative hardware and software technology such as Intelligent Features that enable extended autonomous operation and productivity.
-
product
COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)
CVCT-S20
Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.
-
product
Temperature Calibration Software v5.1
MET/TEMP II
MET/TEMP II software allows you to easily automate the calibration of a wide range of temperature sensors. It provides a comprehensive temperature calibration solution that allows you to test large quantities of sensors, calculate characterization coefficients, and print calibration reports. You can standardize comparison or fixed point calibrations and use multiple temperature sources or references in one test.
-
product
General Lighting & Luminaire Goniophotometers
Photometric Solutions International Pty Ltd
These are Type C/gamma goniophotometers with wide-ranging applications including luminaires, floodlights, streetlights, LED clusters, emergency lighting, flat panel displays and others. These goniophotometers typically have an angular accuracy of better than 0.1°, which is perfect for LED and luminaire goniophotometry. The control software that comes with each system has advanced functions that make testing easy – even for inexperienced users. Additionally, the report generator and other software utilities that are also supplied make these systems powerful and advanced research and development tools.
-
product
4, 8, 16, 32 Channel ARINC429 Test And Simulation Module For PCI
APXX429-x
ARINC429 Test and Simulation bus interface with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s.
-
product
Visual Inspection Software
AdVISE
R&S®AdVISE visual inspection software automates the process of visually monitoring an equipment under test (EUT) during a test sequence. This eliminates human inattention, ensures reproducible results and simplifies the test documentation. A typical application is EMS testing with R&S®EMC32 and R&S®ELEKTRA test software.
-
product
Test Automation
PrimeTest Automation delivers custom test, measurement, and data acquisition systems that include the best hardware and software available. Drawing on vast resources from multiple disciplines, each system is carefully designed and constructed to provide the most accurate and repeatable results. Test systems can be deployed as standalone or as part of an automated line such as a rotary index dial or conveyor.
-
product
Doble Universal Controller
DUC
The Doble Universal Controller is a ultra-rugged tablet device powerful enough to operate Doble's suite of high voltage test equipment and software solutions while being tough enough to withstand the rigors of electrical field testing.
-
product
Nand Flash Tester
NplusT
NplusT was created in December 2002 by Tams Kerekes' 20-years experience in the field of electrical semiconductors and reliability testing.The company started with the sales representation of semiconductor equipment and consumable suppliers. In the meantime, qualified engineering services, linked to the represented products, were provided in Europe.In 2003 NplusT started to market "RIFLE", the non-volatile memory engineering tester, and related services. In a few years, this product has become a reference platform for many memory makers.In 2005 Liliom Laboratories, a Hungarian software development company, merged into NplusT. Thanks to this operation, the company became leader in the test data collection and processing segment.From 2008 a dominant portion of NplusTs turn-over derived from licensing software products. Today almost every European along with several Far East semicon companies license our software products and make use of qualified engineering services.From 2011, NplusT provides turn-key solutions for device testing and characterization, including hardware, software and support.
-
product
Test Benches
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
product
PXI Interface Module, AIT ARINC 429
M3407A
Interface to the LRU in avionics test solution 4, 8, 16, or 32 software programmable Tx/Rx channels with full error injection/detection Programmable high/low speed operation Real-time recording and post analysis of multiple channels Concurrent operation of all Tx/Rx channels PXI triggers, star trigger, and PXI 10 MHz clock
-
product
Portable Appliance Tester
PAT-2E
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
product
Software Tool Especially Designed for Production Process Supervision
LEON OP
The Leon OP is a software tool especially designed for production process supervision. Therefore, the application provides the following key features:- Execution of KT ICT sequences or NI TestStand sequences- Parallel, semi-parallel or sequential execution of test sequences, individually definable per Test Sequence- Customizable User Interface, simple or detailed test views, grid or board layout arrangement possibilities- Tracing into sequence execution- User management with different user levels and restrictions per user group- Displaying execution results and statistics by panel or nest- Supporting interaction with an automation (e.g.: handler system)- Supporting interaction with a process control / MES system- Integrated Callback structure to adopt to different workflows- Maintenance view for fast displaying of fails inside a board- Result History View to quickly access the last test results- Store execution results in result files with user defined format- Autostart-option for running application in automation mode without any operator interaction at all- Several abortion criteria to abort execution by fail count (consecutive or time based)- A Maintenance View for viewing testprobe locations on the DUT is available via Aster Quadview
-
product
Insulation Resistance Measurement
MD 5KVr
The digital insulation tester model MD5KVR is TENTECH's cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TΩ, with 4 preselected test voltages, 500 V -1 kV - 2,5 kV - 5 kV. Other test voltages, from 50 V to 5 kV, can be selected in 25 V or 500 V steps.
-
product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Arc Pro
Otii Arc Pro is an instrument that can precisely source voltage or current and simultaneously measure voltage and/or current. It computes power and energy and syncs with software output, enabling engineers and developers to easily see what drains the energy and optimize the battery life of their devices under test.
