Test Software
programs, procedures or rules and associated documentation pertaining to the operation of a computerized test set.
See Also: Test Software Development, Software Testing
-
Product
Transformer Test Equipment
-
DV Power test instruments perform various diagnostic tests on power and instrument transformers. Even more, a unique feature is a condition assessment of on-load tap changers. Performing a transformer test before their breakage can be crucial.Test instruments are portable and enclosed in durable metal cases. Also, the 19” rack-mounted version suitable for factories is available as well.Applications supported by DV Power transformer test equipment include:Winding resistance measurement (IEC 60076-1)Analysis of on-load tap changers (IEC 60214-1)Heat run test (IEC 60076-2)Automatic transformer demagnetizationTurns ratio measurement of power and instrument transformers (IEC 60076-1)Excitation current measurementPhase angle measurementTransformer vector group detectionDemagnetization status verificationAll of the above-mentioned measurements are performed with the highest accuracy.The advanced DV-Win PC software collects both numerical and graphical results. As a result of that, these features provide an easier and more efficient analysis. After the test, DV-Win software generates a test report with a single click. Furthermore, a user can easily customize the test report and save it in different formats, such as XLS or PDF.Finally, the analysis of on-load tap changers is performed by the new method called dynamic resistance measurement (DRM). This is a non-intrusive method. Therefore, it allows detecting problems in on-load tap changers without disassembling them.
-
Product
Imperial Test Executive
ITE
test
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Modbus Module Test Tool Software
ModTest
-
Modtest 2 software allows the configuration and settings of a Rotork Modbus Module Mk2 inside an individual actuator to be carried out easily and simply over the data bus. In addition, the actuator can also be exercised using this PC based software. The Modtest 2 software is used for diagnostic and maintenance of a Modbus controlled actuator over a serial link from the PC.
-
Product
Test-Track
-
TEST-OK includes TEST-TRACK: Powerful testing software and administrative tools for building a full PCB test. All test commands are pre-programmed to build your specific test routines.Test results are stored in an industry standard database, enabling to trace the results of all tested products, including different test sessions, results and software versions.
-
Product
Car-to-X Test Bench
-
Qosmotec Software Solutions GmbH
The QPER-C2X adaptation, that emulates signal strength between radio devices for Car-to-X communication in the lab, can be combined with the test automation software CANoe from Vector Informatik to enable a fully automated lab test under realistic radio conditions. This combination can be regarded as full test bench setups for Car-to-X test laboratories.
-
Product
Visual Inspection Software
AdVISE
-
R&S®AdVISE visual inspection software automates the process of visually monitoring an equipment under test (EUT) during a test sequence. This eliminates human inattention, ensures reproducible results and simplifies the test documentation. A typical application is EMS testing with R&S®EMC32 and R&S®ELEKTRA test software.
-
Product
Smart Control And Development Universal Software
-
The control software SCADUS (Smart Control And Development Universal Software) is based on Windows operating system. The test control software and test program development and debugging software are done in Delphi. It is designed for a wide base of customers. Each operator and engineer have a separate profile with all screens and software configurations. Online application development is also possible from another computer. The debugger and statistics are offered as standard accessories.
-
Product
SSFDR Software Integration Rig
MS 1112
-
Software Integration Rig (SIR) is an Industrial PC based system is used to test the SSFDR (Solid State Flight Data Recorder) of SU30 Aircraft. SIR is a PXI based test platform and it is used to test independent and integrated software tests of the SSFDR.
-
Product
LEAK TEST MANAGER SOFTWARE
-
Leak Test Manager is a software application for PC compatible with Windows XP, 7, 8 and 10 that allows interfacing ForTest equipment to a computer via an RS232 connection (or Ethernet if optional is available on the instrument)
-
Product
PCI Express 4 M.2 Receiver Test Automation
N5991PM4A
-
The N5991PM4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express M.2 devices and hosts at 8 GT/s.
-
Product
Multiple Module Serial Bus Test Instrument
Bi4-Series
Test Instrument
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant software drivers and hardware enabling straightforward integration into automatic test systems.With the configuration flexibility needed to effectively test every bus format used in defense and aerospace applications, the Bi4-Series instrument plays a key role in reducing implementation time and test system cost.
-
Product
Source And Measure WiFi And Bluetooth Signals
IQview
-
The LitePoint IQview® simplifies WiFi and Bluetooth® device development with powerful tools to both source and measure WiFi and Bluetooth signals and analysis capabilities providing insight into device behavior. The IQview offers seamless compatibility with the IQflex® manufacturing solution enabling test software developed on the IQview to run on the IQflex platform widely deployed in manufacturing environments.
-
Product
Test Receiver
KH3932
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3932 EM1 test receiver is a fully automatic test receiver and the main tool for EM1 testing. The frequency range of the KH3932 receiver is from 9kHz to 300MHz. Equipped with a power absorption clamp, it can meet the power line disturbance power test. After the artificial power network is configured, the power terminal disturbance voltage test can be carried out. The machine has fast test speed and maneuverability. Strong, stable performance, convenient test data processing and other advantages. The KH3932 receiver uses the USB interface to exchange data with the computer, which makes the transmission speed fast and the bit error rate low. Connect to the computer for testing and use the operating environment familiar to the operator to improve work efficiency.The equipped operating software saves the data of a variety of external equipment, and supports plug and play a variety of external test equipment. The software and hardware are developed by our company. The whole machine uses a fully enclosed structure, and the chassis uses highly conductive materials with good shielding effects. Due to the use of specific technologies and processes, the problem of its own resistance is fundamentally solved. The measurement results are in the international general report format, which can be saved in the computer's hard disk or transmitted through the network, printed out directly, and saved using a USB storage device. The report is rich in content and can be printed directly according to user needs without additional editing.The measurement receiver complies with the requirements of the national standard GBT6113.101 and the international standard CISPR16-1.
-
Product
Battery Test Equipment
-
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
Product
Test Automation Platform (TAP)
-
The Keysight Test Automation Platform (TAP) provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments.
-
Product
Test & AMP Measure
IP Traffic
-
IP Traffic - Test & Measure is a software testing tool that can run on any PC with Windows 98, 2000 or XP. It can generate, receive, capture and replay IP traffic, and measure end-to-end performance and Quality Of Service over any IP fixed or mobile network.
-
Product
CEAST VisualMELT Software
-
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
Product
PCI Express 6 Base Specification Receiver Test Automation
N5991PB6A
-
The N5991PB6A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 6.0 ASICs
-
Product
Automated Test Equipment Software
-
The Emerald Software Suite allows users to control and monitor multiple test channels simultaneously. Numerous test components can be controlled from a central control station.Numerous test components, such as cooling modules, environmental chambers, loads and power supplies, data acquisition and diagnostic tools, can be controlled from a central control station.
-
Product
Ethernet Test Fixtures & Software
-
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
Product
Test Pattern Generator Software
ScanExpress TPG
-
To deliver a product meeting the highest standards of quality and reliability, design engineers and test engineers alike must maintain test capabilities throughout the entire product life cycle, from prototype to manufacturing. Automation in test generation is essential to ensure that tests keep up with the rapid development of modern products.The ScanExpress TPG™ Intelligent Test Pattern Generator Software provides a highly advanced, automated boundary-scan test design environment—perfect for quick and efficient creation of complete boundary-scan tests for all IEEE-1149.1 and IEEE-1149.6 compliant circuit boards.
-
Product
Phyview Software Features
-
Included with every PVA-3000 instrument are PVA Interactive (GUI) and PowerShell PSA (script automation) software. Whether running test suites, troubleshooting 10/100/1000 interface issues, or automating QA tests, PVA Software enables high productivity and rapid results.
-
Product
Test Universe
-
Test Universe is OMICRON's comprehensive and easy-to-use testing software for the CMC device family. It allows you to combine a wealth of application-optimized test modules for creating flexible and fully automated test plans that provide you with an enormous range of functions.
-
Product
Mobile App Testing
-
TestFort QA Lab can provide you with mobile application testing services that include testing application software on different mobile devices for its usability, consistency and functionality. Mobile application testing is an integral part of app development process and can valuably decrease your operational costs.
-
Product
UTP Software Suite
-
Increasing customer requirements, shorter product cycles and higher time to market demands dramatically influence the long-term goals in software development. With the Universal Test Platform Software Suite (UTP Suite), we introduce a robust standard that features a great set of tools for configuring, developing, analyzing, debugging and executing test sequences.
-
Product
Testing Services
-
We are professionals who deliver software testing services. We are able to boost your software testing, increase product quality and reduce costs.
-
Product
LCA TAP Plug-In
N4370P01A
-
Keysight Test Automation on PathWave (TAP) is a modern Microsoft .NET-based application for standalone use or in combination with higher level test executive software environments. Instrument plug-ins provide test steps that can be added to work-flow sequences without instrument level programming commands. The LCA plug-in steps further simplify automation by handling the interface to both the PNA instrument and the LCA optical hardware and software and providing the test steps for easy configuration.
-
Product
Test Executive Software
TestBase
-
TestBase is a test executive that supports the visual development, database storage and run-time execution of test program sets.
-
Product
NI TestStand Development Services
-
Simplicity AI have a high degree of ATE software development expertise using NI TestStand, in industry areas such as aerospace, defense and telecoms. With Certified TestStand Architects and Certified TestStand Developers on the engineering team, and holding National Instruments Alliance Partner status, Simplicity AI have the knowledge and experience to deliver advanced test software solutions.
-
Product
AC Power Source
-
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
