Filter Results By:
Products
Applications
Manufacturers
-
product
Trailer Light Testers
Pro-Check 725
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
product
Fully Automatic Transformer Winding Resistance Tester
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
product
Full Range Photodiode Array UV-VIS-NIR-SWIRLaboratory Spectroradiometers
The SR-Series of full range laboratory spectroradiometers is ideal for a wide range of applications, including:*Solar radiance and irradiance measurements*Solar simulator test and classification*LED, laser, light source metrology*Radiometric calibration transfer*Remote sensing applications
-
product
Rotation Luminaire Goniospectroradiometer
LSG-1800CCD
LSG-1800CCD/LSG-1700CCD Goniospectroradiometer is an automatic goniophotometric instrument for luminous intensity distribution measurements with facility for turning the light source. The LSG-1800CCD can do the spatial CCT test when do the intensity distribution test. It is for industrial laboratory measurements the photometric data of luminaires such as LED luminaries, HID lamps, fluorescent lamps and so on.
-
product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
product
7-way Flat (Spade) Pin vehicle side Circuit Tester
7893
Innovative Products of America
The 7-way Flat Pin Trailer Circuit Tester quickly and easily tests trailer circuits on most light to medium duty trucks and campers. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
Tabletop Light Fastness Tester
TF421
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
product
LabVIEW Programming Service
DMC has successfully employed LabVIEW in many industries, including product development, R&D, high-tech manufacturing, and test engineering. Following are a few relevent examples: Laboratory Automation; Carbon Monoxide Detector Testing, Strobe Light Testing, Multi-Station Permeability Test Stand, Hydraulic Fluid Tribology Testing. Manufacturing Automation; Engine Cold-Test Characterization, Smart Battery Pack Manufacturing Test, Automotive Sensor Testing.
-
product
Tabletop Light Fastness Tester
TF419
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
product
Aluminum Film Index Tester
DRK120
Shandong Drick Instruments Co., Ltd.
DRK120 aluminum film thickness tester is new instruments as the development of new packaging material. It is used to test aluminum coating in the barrier film, which is around 35NM thickness. This aluminum coating improves the barrier property a lot, because common gas and aromatic gas couldn’t dissolve in metal. The aluminum coating could protect packing material and avoid light. So thickness test and control of aluminum film is very important, the thickness of aluminum will affect the barrier property of film a lot.
-
product
Single-Functional Testers
3122
The MI 3122 SMARTEC Z Line-Loop / RCD is designed specifically for live circuit testing. The instrument contains integrated characteristics of fuses and RCDs for the evaluation of test results. The online voltage monitoring system allows the operator to control what is happening on three simultaneous voltages in real-time. The bright red and green PASS / FAIL lights and help screens for each measurement make the handling of the instrument easy and clear. All the results can be quickly saved on the instrument and then downloaded via the optional A 1291 EuroLink PRO or A 1290 EuroLink PRO Plus software for evaluation and professional report generation after testing.
-
product
GO-NR1000 Near-Field Goniophotometer
Hangzhou Everfine Photo-E-Info Co., LTD
Suitable for LED light source, LED chip, module and other small light source, the principal function includes: spatial light intensity distribution curve, spatial color distribution curve, iso-lux curve, total luminous flux, effective luminous flux, spatial luminance curve, etc.The test data can be saved as IESNA (*.ies), CIBSE (*.cib), EULUMDAT (*.ldt), CIE (*.cie), CEN (*.cen) and other formats, which can be directly used as the input data of international general lighting design software. Spatial luminance data can be imported into near-field lighting generation software to generate light data that can be imported into third parties (TracePro and LightTools).
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
PXI-2521, 40-Channel, 2 A, DPST PXI Relay Module
778572-21
40-Channel, 2 A, DPST PXI Relay Module—The PXI‑2521 is a general-purpose switch module that features independent double‑pole single‑throw (DPST) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2521 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
GFCI Socket Tester
TEL5
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
product
3 1/2 digits (1999 count) Clamp Meter
KT-9030T
3 1/2 digits (1999 count), unit and sign display. ACA, ACV Measurement. Temperature Test. Continuity Beeper, Diode Test. Data-Hold function. Small size, light weight
-
product
Digital Earth Resistance Tester
8PK-ST1520
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
product
Tap Changer Analyzers & Winding Ohmmeters
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
product
Compact Goniophotometer
LSG-1200A
The compact goniophotometer of LSG-1200A is used to measure the luminous intensity distribution curve, intensity data, spread angle and other parameters for Chip LED, LED Module, LED Spotlight and all other light which beam angle is no more than 180 degree. • Meets the requirements of IEC, CIE and LM-79 standards • Measures beam angle automatically: staple half intensity angle as well as 1/4 intensity angle, 3/4 intensity angle and 1/10 intensity angle which meets the special requirements. • Measured data is matched with international standard form (IES) and can be applied for lighting design by other lighting design software such as DiaLux • LSG-1200A has included a dark room, measures the maximum size of lamps: 180mm • Test range of luminosity: 0.1～30,000lx. Test accuracy of detector: Class 1 • The distance between the tested lamp and detector is 316mm/1000mm • Angle interval: Horizontal angle: 1°/5°/10°/15°/22.5°/30°/45°/90°, Vertical angle: 0.5°/2°/1.5° • The LSG-1200A horizontal automatic rotating on 0°~360° and Vertical automatic rotating on -90°~+90° • Test accuracy of angle: ±0.2° Work with the follow instruments as a System
-
product
HV & AC Resonant Equipment
Kvtester Electronics Technology Co.,Ltd
This kind of products are small in volume, light in weight, with compact structure and multiple function, general-purpose and easy to use. Applies to the test of frequency or insulating intensity under DC ,HV for all kinds of HV electric equipments, components, insulated material in electric system, industrial and mining enterprises, traffic , post and telecommunications, science institute, etc.
-
product
GFCI Receptacle Tester
RT600
Designed to detect the most common wiring problems in standard 120V receptacles.Also tests GFCI receptacles for proper operation.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.
-
product
6-24V Car Circuit Tester
1951
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable for earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
product
Compact Hydraulic Vibrator Force Simulator
JF Series
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
product
Optical Multimeters
Optical Multimeter integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules but work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages.
-
product
Automated Thermal Stress System
ATSS Series
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
product
UNIVERSAL NOID LIGHT
27800
Tests throttle body injectors, ported fuel injectors and sequential central port injectors, Adjustable probe fits all electronic fuel injection systems and swivels to fit various widths, Flashing light indicates normal pulses, no light indicates a problem.
-
product
PPID-2000 Photosynthetic Photon Intensity Distribution Test Unit
Hangzhou Everfine Photo-E-Info Co., LTD
It is mainly used for testing plant lighting products. With the EVERFINE GO-R5000 goniophotometer system, it can realize the measurement of plant photosynthetic photon intensity distribution (μmol/s/sr) in the whole space. In addition, the device can also realize the test of photosynthetic photon flux, far red light photon flux, photosynthetic radiation efficiency and other parameters, referring to DLC, ASABE, DIN, GB, CQC and CSA related international plant lighting standards .
-
product
Spectral Response SystemsQuantum Efficiency SystemsIPCE Measurement Systems
QE system provides electronics and software designed for fully automated measurement of external quantum efficiency of solar cells. All systems include probes and a fixed plate sample stage for samples up to 150 mm x 150 mm. The main system components include: custom designed software, measurement electronics, and computer system (Windows 8 operating system). The measurement involves focusing monochromatic light to a spot on the device under test, then accurately measuring the photon flux and current from the test cell. The system utilizes a dual beam configuration with lock-in detection, providing an absolute accuracy of ±3%. The QE system uses a grating monochrometer with silicon/InGaAs/Ge detectors. The system includes automatic order sorting filters and two light sources for monochromatic illumination (a Xenon- arc lamp and a halogen lamp). A single lock-in amplifier is used to measure both the reference detector and test device. The main system comes with all the hardware needed to measure quantum efficiency, a fixed plate sample stage and probes.
