Filter Results By:
Products
Applications
Manufacturers
-
product
Programmable AC Power Source
Model 8600 Series
- Compact size and light weight, standard 19″ rack construction- Step-less frequency setting from 45 to 450Hz- Very low distortion sine wave output- Output voltage range selectable 135 or 270V AC- Galvanically isolated input/output- Independent on/off switch for input and output- 16×2 vacuum florescent display for parameter display- Complete operation through push switches and a digital rotary encoder- Automatic protection against overload, short circuit and over temp.- Built in PFC to provide 0.99 input power factor and wide input range- Conforms to EN55022, class A, safety standard EN60950
-
product
500-1000W AC Power Source
CX-P150
Shenzhen Chuangxin Instruments Co., Ltd.
The AC power source is made by adopting microcomputer processing chip and high power device. It provides a stable pure sine wave and has voltage,
-
product
Pulse Function Arbitrary Noise Generator
81160A
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
product
Partial Discharge Testing
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
product
General Purpose Basic Carrier Demodulator
CD15
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
-
product
Phase Squence Tester
Measurement Range3 phase check for AC 90V ~ AC 600V (Sine Wave) Operation Frequency45Hz ~ 70Hz Test Time LimitationAC 110V(continuous)AC 220V(3 hours)AC 480V(12 minutes)AC 600V(3 minutes) Power Supplyno battery required Color change LED phase direction indication
-
product
1mV-300V / 2 CH. Milli-Voltmeter
Digital MVT-172D
Is applicable to measure RMS value of sine wave with frequency range 5Hz~2Mz and voltage range 100μV~300V. This instrument has a 4 digit display with high precision, small frequency effected errors and high input impedance. There are three display ways including voltage, dB and dBm, supplying a clear and intuitive display. Auto measuring range switching makes your usage more convenient. All switches are touch switches with high quality, providing good hand feeling and high reliability.
-
product
Power Signal Generator
PSG-300
The PSG-300 contains a linear precision power amplifier with a wide bandwidth (DC-300 kHz), suitable for all applications concerningfast alternating signals at high output power. The built in generator provides sine, square and triangle waves.
-
product
Utilities
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
product
2-Channel 400MHz DDS Signal Generator
2940A
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
product
1208/9a Optical Distribution, RX/TX
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
product
Vector Network Analyzer
Bode 100
With the multifunctional Bode 100 you get an exact picture of your electronic circuits and components in a frequency range from 1 Hz to 40 MHz. The Bode 100 is not only a state of the art Vector Network Analyzer, it also works as: Frequency Response Analyzer, Impedance Meter, Gain Phase Meter, Sine Wave Generator.
-
product
Electrodynamic Vibration Generator System
LVD-100KG
• Vibration table size: 500*500mm (Other size can be designed) • Vibration: 0~5mm (Adjustable range P-P). Vibration waveform: sine wave (half wave and full wave). Acceleration speed: 0~20g (Adjustable) • Maximum test load Capacity: 100kg • Accuracy: Frequency can be displayed to 0.01 Hz. Precision 0.1 Hz. • Sweep Frequency function (1~600Hz): (Upper frequency, Lower frequency, Time range) It can set real standard arbitrarily to sweep frequency back and forth • Programmable Function (1~600Hz): It can set each segment in 15 segments arbitrarily (frequency/amplitude/time/acceleration), and it can be recycled • Frequency doubling function (1~600Hz): 15 segments multiplied-increase: 1)Low to high frequency 2)High to low frequency 3)Low to high and then to low frequency, it can be recycled • Logarithmic function (1~600Hz), 3 modes of logarithm/can be recycled: 1)Lower to upper frequency 2)Upper to lower frequency 3)Lower to upper and then to lower frequency • Measuring instrument: To display amplitude, acceleration speed and the maximum acceleration speed.
-
product
Function Generators
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad
-
product
2 phase 120/240VAC SDP-30KW split phase inverter
SDP-30KW
Zhejiang Sandi Electric Co., Ltd
SANDI SDP series Pure Sine Wave Inverter is the one of the most advanced technology DC to AC conversion products in the world, it’s suitable use for areas without electricity, providing a complete power solution for strict demand applications. With SVPWM technology it has high conversion efficiency, high instantaneous power and low losses power output pure sine wave, applying to capacitive, inductive and nonlinear mixed-load, with superior load capacity, perfect protection function: overload, short circuit, low/over battery voltage, improper operation etc, which won’t cause mechanical failures.
-
product
RMS to DC Converters
RMS-to-DC converters manufactured by Analog Devices are used in a wide variety of applications where precision and low power measurement of ac signals is the prime objective. An ADI rms-to-dc converter offers real time measurements, meaning there are no latency issues such as those that limit the frequency response of other technologies—the dc output is simply the equivalent of the rms input, over a wide range of input frequencies, and for complex waveforms not limited to sine waves. ADI offers a wide range of rms-to-dc converters optimized for the most demanding performance, power, and cost applications satisfying true rms needs.
-
product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
product
Desktop AC Power Supply
DRJ Series
DRJ Series is a stable sine wave output AC power supply of the world's smallest class that integrates the functions of rack-mount multifunctional AC power supply DRA Series in a desktop size. It is a new type of AC power supply that addresses both space saving and high-quality output that are required in experiments, evaluation tests, production line and so forth. With worldwide input feature DRJ can be used anywhere in the world. In addition, it delivers simple operability in a compact size, allowing first timers to operate easily.
-
product
Online UPS
POWERPACK SE SERIES 10/15/20 kVA
Sine wave output and clean energy for computers and all sensitive equipments. Online UPS protects your equipments from all mains problems. Online UPS can operate with a wide voltage range so that battery power.
-
product
1mV-300V / 1 CH. Milli-Voltneter
MVT-171
Is applicable to measure RMS value of sine wave with frequency range 5Hz~2Mz and voltage range 100μV~300V. This instrument has a 4 digit display with high precision, small frequency effected errors and high input impedance. There are three display ways including voltage, dB and dBm, supplying a clear and intuitive display. Auto measuring range switching makes your usage more convenient. All switches are touch switches with high quality, providing good hand feeling and high reliability.
-
product
AC Power Source
LSP-500VAR
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
product
UPS (Uninterruptible Power Supply)
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
product
Audio Generator
AG-51
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
product
Audio Test Tone Generator
ToneGenerator
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
product
Signal Generator
MAG-2015AD
Feature:*Signal frequency: 0.1Hz~15MHz, continued*Wave form: square,sine*Output attenuator: 0dB,20dB,40dB,60dB*Output level: 20Vp-p in open ciruit,not less than 10Vp-p with 50Ω load*Rising edge of Square not more than 35ns at 2MHz*Sine distortion less than 1%,amplitude-frequency characteristic ±0.5dB with in 2MHz, ±3dB above 10MHz*Frequency Counter: 20Hz~30MHz*Power supply: AC 220v (110v optional)
-
product
Pressure Sensor Kit for Changing Ranges
DP15TL
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
product
DC-AC Sine Wave Inverters for Ultraviolet (UV) Lamps
UV Lamp Inverters
The sine wave inverters are designed and built to meet any customer input/output and mechanical configuration requirements.
-
product
3-Channel PXI Function Generator
41-620A-003
The 41-620A is a compact 3-channel function generator provided in a PXI 3U single-slot module and is fully backward compatible with our 41-620-003 module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. This module can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
product
Trimble Hydrographic Extensions
SCS900
Users of Trimble Construction SCS900 software are now able to easily measure water depth and execute accurate small-scale hydrographic surveys. Ohmex Ltd has made use of the SCS900 Software Developers Kit (SDK) to produce a software utility that runs on the controller and supplies depth data to SCS900. This increment in functionality further enhances the use of the SCS900 system on marine construction sites where dams or waterways are present.The concept of the Sonar extension to SCS900 is to enable the construction user to execute simple Hydrographic surveys using their SCS900 software together with existing positioning equipment, no need to learn another package or convert to new reporting facilities, the sonar effectively behaves as an extension to the existing survey detail pole for measuring water depth. The software is an inter-application package with both the SCS900 and SonarMite applications running concurrently on a TSC2, Tablet or PC platform. For evaluation purposes the SonarMite application has a 'Simulator' mode that generates sine wave data without the need for a SonarLite echo sounder to be connected ...
-
product
Pulse Acquisition Board
MS 1818
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
