Filter Results By:
Products
Applications
Manufacturers
Semi
active or passive elements connected as an electronic circuit using a crystalline subtance, eg. silicon or germanium.
See Also: E84
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
Host emulator
E84
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
product
Emulator
GCI E84
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
product
High Power LED Photo-color-semi Automatic Selector
Shenzhen Chuangxin Instruments Co., Ltd.
Can divide LED in to several groups by chromatic coordinates, correlated color temperature, dominant wavelength or luminous flux.
-
product
Flexible Current Sensor Probe
CTA
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
product
Wafer Probers
Full Automatic Wafer Prober. Semi Automatic Wafer Prober. High Current Probe Block. 6-inch Manual Prober. 8-inch Manual Prober. 12-inch Manual Prober.
-
product
Hand-Held, Battery-Operated Multi-Frequency Eddy Current Instrument
US-454A
United Western Technologies Corp
The US-454A is a portable, hand-held, battery-operated multi-frequency eddy current instrument that can be connected to a laptop, PC and motion controllers for use in semi- or fully automatic data collection applications. Two encoder inputs enable position stamping of data. Pulse-on position input is ideal for motion control applications. Ethernet and USB capabilities allow instrument control along with time- and position-stamped data transfer to the client computer. Built from the rugged US-454 architecture, the US-454A offers single- and multi-frequency inspection, frequency mixing capabilities, enhanced signal-to-noise ratio, USB, Ethernet and data storage capability, and unprecedented digital strip chart data collection.
-
product
Metrology Solutions for Semiconductors
Bruker Semiconductor develops, manufactures, markets, and supports metrology solutions for thin films, which are based on novel, rapid, non-contacting and non-destructive X-ray technology. With Bruker’s acquisition of Jordan Valley Semiconductors, a name synonymous with unparalleled worldwide customer service and support, 75% of the world's top 25 semiconductor manufacturers rely on Bruker metrology tools for front-end and back-end applications, including development of their next-generation thin films. Bruker commitment to innovation and technology leadership drives the continued release of new advancements in metrology, and has garnered numerous awards and industry recognition. In applications ranging from C-S thin films materials characterization to wafer substrate analysis and defect detection, Bruker’s systems provide simulation analysis and fit. HRXRD, XRR, WA-XRD, and XRDI measurement types are fully supported, enabling researchers, production engineers, and process developers unparalleled capabilities. Whether you are a semi and C-S fabricator, R&D center or academy, or an industry materials research facility, Bruker has a specifically designed solution for your metrology needs.
-
product
300W to 1800W - Single Output
HWS Series
*Limited Lifetime Warranty*UL 508 approved*SEMI F47 Compliant (high line AC)*Universal Input (85 - 265VAC)*High Efficiency*Class 1 Div 2 option (/RY suffix)
-
product
600W to 1056W - Single Output
SWS-L Series
*Low Cost*Active Power Factor Correction*Input Transient Protected IEC61000-4*Universal Input (85 - 265VAC)*SEMI F47 Compliant (208VAC)*Medical Approvals (SWS1000L)
-
product
Normalised Site Attenuation
NSA
Normalised Site Attenuation (NSA) is measured in accordance with CISPR 16-1-4 and ANSI C63.4 in semi and fully anechoic environment.
-
product
Compound Semi | MEMS | HDD Manufacturing
KLA has a comprehensive portfolio of inspection, metrology, and data analytics systems to support power devices, RF communications, LED, photonics, MEMS, CPV solar and display manufacturing. High brightness LEDs are becoming commonly used in solid-state lighting and automotive applications, and LED device makers are targeting aggressive cost and performance improvements, requiring more emphasis on improved process control and yield. Similarly, leading power device manufacturers are targeting faster development and ramp times, high product yields and lower device costs, and are implementing solutions for characterizing yield-limiting defects and processes. KLA's inspection, metrology and data analytics systems help these manufacturers control their processes and increase yield.
-
product
Sematech Analysis and SEMI Standards Analysis
Rocky Mountain Laboratories, Inc.
Rocky Mountain Laboratories, Inc. provides SEMI Standards analyses that conform to the following SEMATECH and SEMI Standards for testing of passivated 316L stainless steel components being considered for installation into a high-purity gas distribution system:SEMASPEC #90120401B-STD (SEM Analysis)SEMASPEC #90120402B-STD (EDS Analysis)SEMASPEC #90120403B-STD (XPS Analysis)SEMASPEC #91060573B-STD (Auger (AES) Analysis)SEMI F60-0306 (based on F60-0301) (XPS Analysis)SEMI F72-1102 (Auger (AES) Analysis)
-
product
Sapphire 3D Microscope
WDI-2000
The Sapphire 3D Microscope: HS-WDI-2000 was designed with high quality lighting parts and a good optical system design,can get a very clear image.with the digital camera,it can provide the image in time, widely used in LED,Solar,SEMI…
-
product
15W to 150W - Single Output
HWS-A Series
*Limited Lifetime Warranty*UL 508 approved*SEMI F47 Compliant (high line AC)*Universal Input (85 - 265VAC)*Higher Efficiency than HWS Series
-
product
Hydraulic Universal Testing Machines
UH-X/FX Series
Environmentally and operator friendly state-of-the-art universal testing machine The operability and visibility of the computer-controlled hydraulic servo type universal testing machine (UH-X) and the high-performance universal testing machine (UH-FX), equipped with front opening type hydraulic grips, have been greatly improved by the adoption of a large color touch panel. Equipped with a semi autotuning function that automatically adjusts the control parameters, stress control and strain control (ISO 6892 compliant) can be easily carried out without the need for a preliminary test. The UH-Xh and UH-FXh models feature a new hybrid hydraulic oil source that reduces the required quantity of hydraulic oil, thereby achieving a major reduction in electrical power (about 50 %).
-
product
Flexible Waveguide
Flann offers a number of solutions for flexible waveguide interconnect including waveguide-coaxial-waveguide and semi rigid. Traditional flexible waveguide solutions are available on request.
-
product
Serial to Parallel Controller
E84 SPC
300mm equipment manufacturers utilize this off-the-shelf E84 communications controller to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection.
-
product
10W to 100W - Single Output
DRL Series
*High Efficiency, up to 90%*Low Profile for Building Automation*Class II Double Insulation*ErP Compliant Design*Low No Load Power Consumption*UL 1310 Class 2 Compliant*SEMI F47 Compliant
-
product
Semiconductor Package Wind Tunnel
WT-100
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
product
Semi-Portable Gas And Leak Detectors
Semi Portable Gas Detectors and Leak Detectors meet the diverse requirements for gas detection industries throughout the world. Our range offers an ideal solution where a temporary detection or contractual detection is required for a specific project or incident.
-
product
Battery Pack ATS
8700
Chroma transfers its successful experience in 8000 ATS which is quite well-known in the power electronics industry to the battery application field by developing the Test Items specifically for the battery industry. It can perform automatic tests on the Battery Management System (BMS), semi products and finished products tests on the production line as well as provide long term maintenance and service to the battery module. 8000 (8700) ATS has flexible hardware architecture that can select a variety of hardware devices, such as DC Power Supply, Electronic Load, LCR Meter and 6 1/2 digits Meter, etc. to comply with different automatic testing requirements for various applications. In addition new hardware and test items can be expanded to meet the demands for inspecting the highly customized battery products with diversified tests. The capabilities supported are:
-
product
Trace Moisture Analyzer
PPM1
Model PPM1 is a trace moisture analyzer designed specifically for monitoring moisture levels in dew point and PPM units. This trace moisture analyzer utilizes an electro-chemical (P205) sensor in combination with a proprietary semi permeable diffusion membrane.
-
product
EasyMatrixCode
Automatic detection of the code in the imageDecodes ECC200, ECC000, ECC050, ECC080, ECC100 and ECC140 codesComputes quality indicators as per ANSI/AIM, ISO/IEC 15415, ISO/IEC TR 29158 and SEMI T10-0701 standardsVery fast operationImpressive robustness to noise, blur and distortionSupport of GS1 Data Matrix codesEfficient reading of codes in grid layoutMultiple codes reading
-
product
500W to 1500W - Single Output
LZSA Series
*Five year warranty*-40°C to +71°C Operation*MIL-STD-810E Vibration / Shock*Input transient protected*UL508, SEMI F47, Factory Mutual (Cl 1, Div 2)*Rugged design with conformal coating*Superior thermal design
-
product
Machine Vision Camera - 1.3 MP, 60 FPS, e2v EV76C560, Color
Flea3 USB3
The Flea®3 line of USB3 Vision, GigE Vision and FireWire cameras offers a variety of CMOS and CCD image sensors in a compact package. The Flea3 leverages a variety of Sony, ON Semi, and e2v sensors ranging from 0.3 MP to 5.0 MP and from 8 FPS to 120 FPS. For FLIR GigE and USB3 cameras with the latest sensors and most advanced feature sets, please refer to our Blackfly S and Oryx camera families.
-
product
Control & Automation Solutions
Produce a consistently high-quality product with a control system that’s easy to integrate into any process, simple or complex. Probat control systems feature clearly designed user interfaces and the ability to store and export production data as needed. Available as both semi- and fully automatic systems, our control systems enhance the performance of our commercial coffee roasters and grinders to yield superior results.
-
product
Test Handlers
Boston Semi Equipment test handlers are designed for optimum production performance on your test floor.
-
product
Easy E23 / E84
Objective Solutions' Easy E23/E84 product line is designed to simplify the integration of SEMI E84 and E23 into Process Equipment and Factory Vehicle systems. The models provide a standard E23/E84 infrared interface to AGV/OHV and process equipment, utilizing Hokuyo transceivers. The Easy E23/E84 units have been developed to work as-is with Hokuyo IR transceivers and as an option, with opti-isolation as required by direct-connect applications. They enable simple integration to process equipment or AGV application programs.
-
product
Electric Burn-in Board Carts
Conforms to SEMI ergonomic standards Holds and transports card cages for semi-automatic loading/unloading. Holds up to 10 burn-in boards. Raises and lowers the burn-in boards for easy loading/unloading of boards into ovens or onto test benches. Cart can be adapted to dock with any Micro Control oven.
