Filter Results By:
Products
Applications
Manufacturers
Safety Test
Check to determine whether a device is free from hazards.
-
product
Reformer Test Station
Whether your application is hydrogen, natural gas, or biogas reformation, Greenlight can provide an appropriate reformer test rig, including furnace, gas mixing with water content and pre-heating, gas pressure and temperature control, and automated safety monitoring of the reformer module.Greenlight''s reformer test rigs operate on our reliable automation software for 24/7 dynamic operation.
-
product
Medical System
Sentinel I
Chroma Systems Solutions, Inc.
The Sentinel I System provides fully automated Electrical Safety Testing to IEC/EN/UL/CSA 60601-1. This system is ideal for testing medical products with one or no patient connections or low volume production where operators can manually change leads between different patient connections. This is a 5 in one Hipot test system that can test Hipot, Ground Bond, Insulation Resistance, Patient Leakage, Earth Line Leakage, Enclosure Leakage and Patient Auxiliary Leakage.
-
product
HV Test System up to 20000 Volt
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
product
Digital Tachometer Testers
BCE13
D.Marchiori (DMA) manufacture double or triple tachometer testers. They use precision controlled DC motors with coaxial optical encoders controlled by a dedicated microprocessor. A quartz timing circuit provides maximum accuracy and control stability. Speed values (% or RPM), rotation direction, transmission ratio and 100% RPM values can be selected separately for each motor. The test set can apply star or triangle resistive load and read the output voltage for generator checks; by entering RPM and test voltage limit values the full generator check can be automatically carried out. The internal printer provides copy of the test results. Safety limits to protect UUT can be set separately for each motor.
-
product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
product
Surge / DC Hi-Pot Consoles
HC Model
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
product
SuperGuard C Library Safety Qualification Suite
The SuperGuard C Library Safety Qualification Suite is a requirements-based test suite for the C standard library with full traceability between the requirements derived from the ISO C language definition and the individual library tests. It is designed to support the qualification of implementations of the C standard library for safety-critical applications, both for third-party (COTS) and for self-developed or maintained C library implementations.
-
product
Single Function Installation Testers
A handheld insulation resistance and continuity tester. Its unique integrated safety probe puts the LCD and test probe in the user's line of sight whilst making measurements.
-
product
Meter Qualification Boards
WECO 8020, 8030
WECO Meter Qualification Boards by Radian Research enable extensive functional testing of single-phase and three-phase revenue grade electricity meters. Unlike Warm-up Boards and Load Boards that are limited to just powering the meter or applying a fixed current, WECO Meter Qualification Boards can test a variety of communications, disconnect and safety features. The WECO 8020 and 8030 have varying capabilities based on your requirements. They feature an innovative open socket design exclusive to RADIAN that ensures optimum operator safety. Capability, versatility and safety combine to make WECO Meter Qualification Boards THE logical choice.
-
product
Altitude Test Chamber
Aircraft and its components are subject to extreme pressure and climatic conditions during flights. These parameters have a significant influence on the functioning of individual components, and they must be monitored and measured for safety reasons. CME Altitude chamber allow for the testing of aerospace components in an environment with controlled pressure, temperature and humidity parameters. An altitude of 100,000 feet [10 mbar] can be simulated in the test space.
-
product
Voltage Detector / Phase Comparators
VisualPhase
Hachmann Innovative Elektronik
With the VisualPhase line you get a type series of handy, exact and easily operated multi-functional devices with integrated voltage detectors, phase comparator and maintenance testers. Equipped with a thorough self test to ensure reliable function, a permanently enabled interface-tester to warn against defect interfaces and the connectability to HR, MR, LR, LRM or LRP string parts every VisualPhase delivers uncompromising safety.
-
product
Battery Testing System
C8000
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
product
Non-Trip Earth Resistance Measurement
M73
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
product
Downloadable PAT Tester
Apollo 600+
The Apollo 600+ features a built-in camera for visual test records, a USB memory port for data transfer and a comprehensive range of electrical safety tests with user configurable test sequences and checklists for PAT, PPM and PPE. It has storage for up to 50,000 test records and is compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
product
Hipot Tester
STM/L
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
product
Breakdown Voltage Tester
ZDS-50B
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
product
Hipot Tester
Sentinel
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
product
Photovoltaic and Electrical Installation Testers
3108
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
product
Regenerative Power System, 950 V, 20 A, 10 kW, 400/480 VAC
RP7963A
The RP7963A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
product
High Voltage Relays
B-1001
Air insulated types for isolating loads, tap selections, safety discharge & grounding to help meet OSHA and other safety regulations. Ratings from 1mA to 800 amps continuous, to 100,000 amps capacitor discharge. Peak 1 minute test voltages from 5kV to 300kV. Single or Multipole. Auxiliary contacts are optional on all types. Options include latching, extended life, and tungsten contacts available for high current closing. DC, 25-800Hz & air pressure actuation available. Also usable in oil or insulating gas with increased ratings.
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
product
Mobilize
A complete wireless solution that connects your Pronk test equipment to your smart device!* Take complete control of your Pronk products — Safe-T Sim® Mobilize Electrical Safety Analyzer, Mobilize SC-5 SimCube® NIBP Simulator, Mobilize OX-2 OxSim Flex® SpO2 Simulator, and Mobilize FlowTrax® IV Pump Analyzer — to set up your own test protocols or run your CMMS procedures right from your Apple iOS device.
-
product
Custom Testing
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
product
Fully Automatic Transformer Oil Test Set
1. Test as per International standards NMC insulating oil testers are fully automatic micro controller based system,completely self-contained,compact and portable giving smooth variable test voltage from 0 to 60, 80, or 100 kV for testing the dielectric strength of insulating oil in accordance with all international standards like IEC156/IS6792/ASTM D 1816/ASTM D877/ UNE 21 specifications.2. Auto mode NMC insulating oil testers are fully automatic type.1) IEC-156, IS6792, ASTM D 877, ASTM D 1816, UNE 21.2) Withstand Test A3) Withstand Test B4) 5 Minute Test5) User defined3. 100 Test results storage capacity NMC insulating oil testers has a storage capacity of 100 test results which can be recalled and printed.4. LCD display NMC insulating oil testers use LCD for easy readability of the BDV test results.5. Built in printer The printer used is a thermal paper print outs.The paper rolls can be easily installed by any person.6. User Friendly RS 232 Interface RS 232 interface is very easy to use to communicate stored data which can be saved in text format.7. Safety protection Safety interlocks are provided on the test chamber.Zero interlock protection to ensure operator safety.8. Accurate Performance The kit not only has all basic functions of an insulating oil tester but also has unique features that are seldom seen in similar products. For e.g. PROOF test A, PROOF test B, 5 Minntes test, LCD to display all test data.It ensures high work efficiency and reliability in any tough environment.
-
product
Power Control
Educated Design & Development, Inc.
As a general purpose dual-voltage isolation transformer for step-up (120 to 240 VAC), step-down (240 to 120 VAC), or straight 1:1 isolation (120 to 120 VAC or 240 to 240 VAC). Models with a suffix "UC" are provided with a safety jack for access to the transformer secondary center tap (connected to the transformer center tap only in the 240 VAC output setting). This connection may be used in conjunction with a Dielectric Voltage Withstand test.
-
product
Current And Voltage Transformer Test Set
iCT1
iCT1 - CT/VT Test Set is the NEW and most advanced portable equipment capable to test current, voltage and combined transformers.With the low voltage method, known as "DC method", iCT1 is able to test Current Transformers with a very high saturation voltage, up to 30 kV, in a complete safety mode. Quick and easy to use tool, iCT1 allows to perform tests in one shot without changing the connection to the CT, thanks to the integrated 5-TAP Switchbox.
-
product
Cord Guard Flexing Apparatus
CGF-45
Is designed & manufactured to perform the test specified in many standards to determine compliance with safety requirements related to cord guard flexing. It can be used to test cord guards in Electrical Appliances, Portable Power Tools & other similar equipment & is designed to meet the requirements of several international and national standards.
-
product
Battery Test Chambers
Our battery test chambers are equipped with safety features conforming to industry safety standards enabling testing to a variety of conditions and specifications including extreme temperature cycling, humidity, vibration, and/or altitude. Russells Technical Products battery test chambers are used in a wide range of battery testing applications including lithium ion, battery packs, lead acid batteries, modules and more.
-
product
sbRIO-9229 , Non-Enclosed, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780874-01
Non-Enclosed, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9229 performs differential analog input. The sbRIO‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Non-enclosed modules are designed for OEM applications.
