Filter Results By:
Products
Applications
Manufacturers
Pick-up
-
product
Speed Pick-up
SU63
The Validyne SU63 is an AC inductive speed pick-up used for RPM measurement on high-speed rotating equipment. The SU63 is a tightly-wound coil with a laminated core that can be conveniently mounted on rotating equipment so that the magnetic field of a magnetized nut or part passes through the coil windings. The moving magnetic field produces a voltage within the coil proportional to its rate of change and the strength of the permanent magnetized part. The frequency of this inductive voltage spike is fed into an oscilloscope or counter to determine RPM.
-
product
Piezoelectric Vibration Pickup
PU-6GHT6
*High-sensitivity type for sensoring*low-rotation from 0.2Hz
-
product
Gated Integrator | Boxcar Averager
GIA100
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
product
High Temperature Magnetic Speed Sensors
SPECTEC Innovative Sensor Solutions
High temperature speed sensors (up to 454° C) are sensitive, shock resistant & reliable for high temp applications in harsh environments, such as race car engines and transmissions. SPECTEC's high temperature magnetic speed pickups are used as transmission sensors, engine governors, output shaft sensors and flow meter sensors. SPECTEC's high temperature magnetic pick-ups are standard in 5/8-18, 11/16-24 and 3/4-20, and M18 shell sizes.
-
product
Optical Pickup
1037-DTS
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
product
Lock-In Voltage Preamplifier
SR550
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
product
Secondary Injection Relay Test Set
TD 1000 PLUS
TD1000+ is a protective relay test set especially designed to give the commissioning engineers a multitasking and highly reliable testing equipment. In comparison with T 1000 PLUS model, TD 1000 PLUS has two current outputs to test the differential relay characteristic curve, besides the pick-up current.
-
product
EZ Tach +Plus Automotive Tachometer
328
*Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. *Reads engine revolutions from 0 to 20,000 RPM *Picks up RPM signal wireless or with supplied inductive pickup *Great for setting idle speeds! *Built-in LED Flashlight which can be used while taking measurements *Backlit LCD display *Accuracy +10 RPM
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
-
product
Lightweight Vehicle Surveillance System
LVSS
The skid-based LVSS converts a standard commercial pickup into a rapidly deployable command and control center. Within minutes, a single operator can set up the LVSS and report for full perimeter duty from the comfort of the cab. When it’s time to relocate, the mast and its mounted FLIR cameras, radar, and sensors, stow out of sight for covert transportation.
-
product
Piezoelectric Vibration Pickup
PU-7ALT6
*Upper outlet type*Use in water up to 15 meters*depth enabled
-
product
KYZ Indicator and Tester
1031-C3, 1031-C6
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
product
Piezoelectric Vibration Pickup
PU-6ALSF
*Side outlet type*Easy to remove due to cap nut type*Use up to 80 ℃ enabled
-
product
Saluki SE4002 FET Input Preamplifier
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
product
EZ TACHOMETER PLUS
ETP328
*Small engine tachometer reads engine speeds up to 20,000 RPM*Works wirelessly or with inductive pick-up clip*Accuracy: +/- 10 RPM
-
product
Piezoelectric Vibration Pickup
PU-626E
*Connector type with upper outlet*Waterproof (IPX6), suitable for a wide range
-
product
Speed Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Speed Measurement Trainer comprises of photo reflective & magnetic pickup sensors, fractional HP cc.
-
product
Optical Power Meters
A handheld optical power meter, which is most suitable for production of LDs, optical pickups and drives for optical disks.It was developed to meet functions and performance suitable for CD/DVD production.
-
product
AC Susceptibility
The AC Susceptometer option uses a small primary excitation coil to apply an AC field to a sample (typically 1mT at frequencies from 0.1 Hz 10000 Hz). A pair of secondary pick-up coils positioned close to the excitation coils are used to detect the sample response.
-
product
Acceleration Pickup Calibrator
VX-1100A
VX-1100 is for a piezoelectric type accelerometer which is widely used for measuring vibration. This compact calibrator is effective for checking operation(sensitivity) sensors before measurement to acquire accurate data.Built-in sensor amplifier and display in one unit allows direct reading of the sensitivity. This calibrator excites the sensor at a frequency of 159 Hz and acceleration of 10 m/s2 rms, and the sensor outputs can be used as calibration signals for a vibration measuring system.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Remote Receiver
10780F
The Keysight 10780F Remote Receiver with fiber-optic pickup provides maximum layout flexibility for Keysight laser interferometer positioning systems. Remote pickup capabilities allow mounting of the heat-dissipating receiver electronics away from measurement areas, resulting in high measurement stability, accuracy, and repeatability.
-
product
Piezoelectric Vibration Pickup
PU-661D
*Side outlet type*Waterproof (IPX7) and suitable for*high temperature(-10℃ to 150℃)
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
Piezoelectric Vibration Pickup
PU-7SLT6
*Upper outlet type*Use in water up to 50 meters*depth enabled
-
product
2WD Dynamometers
MD-500-SE XL
The 500 series dynamometer has a larger big brother – the MD-500-SE XL! The 500-SE is an excellent 2WD performance dynamometer and the XL model expands on these traits by adding in a much wider 98-inch outer track and a HUGE mechanical flywheel to increase the mechanical inertia of the dyno to about 2,000-lbs. This additional inertia helps reduce the duty cycle burden on the eddy current PAU and even allows for pulls to be done in a pinch in inertia-only mode. The XL handles vehicles like diesels and Ford Raptors where the 500 is a bit too narrow for these types of applications. The MD-500 XL’s multiple upgrade paths allows for an AWD upgrade in the future and enables it to accept a second eddy current PAU for increased loading capability. We’ve seen this dyno handle almost 2,000-hp to the wheels on power sweeps so don’t be fooled by the 1,500-hp peak measurement specification. If your tires will hook you can measure as much power as you are laying to the rollers. The large K250 eddy current PAU has plenty of torque for testing and tuning anything from your local diesel pickup crowd and local LS guys to classic carb stuff and front wheel drive cars. The 500-XL is great product at a great price with tons of range. It is also easy to install – buy the aboveground kit with the 16-ft ramps and have this dyno set up and ready to roll in your shop in a half a day! if you want to know more call us! We are always happy to answer questions.
-
product
Automated Pick And Collection Tool Of Cell Colonies
CELL PICKER
Pickup and Remove Cell Colonies with Complete Freedom
-
product
Heavy Duty Dynamometers
MD-250-HD
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
product
Lock-In Voltage Preamplifier
SR552
Stanford Research Systems, Inc.
The SR552 Voltage Preamplifier is designed to work with SRS lock-in amplifiers, providing gain where it is needed most?right at the experiment. The preamplifier minimizes noise and pickup in the connecting lines and can reduce measurement time in noise-limited experiments.
