Filter Results By:
Products
Applications
Manufacturers
Open Short
Pinpoint open circuits.
-
product
3.5mm Short Open Load Thru 4-in-1 Analyzer Calibration Kit
Fairview Microwave’s portable calibration kits consist of two models, both with a compact, lightweight, 4-in-1 design package. These short-open-load-through (SOLT) calibration kits feature precision 3.5mm connectors, have a 26.5 GHz calibration capability, gold plated short-open-load-thru and include a handy lanyard. These SOLT calibration kits have a phase deviation of +/-2 degrees maximum and return loss of 30 dB minimum and feature an impedance level of 50 Ohms nominal. They are ideal for telecommunications, military electronics, automotive, medical, aerospace and consumer electronics industries.
-
product
High Volume Semiconductor Substrate Interconnect Tester
GATS-2100
Pre-align *load *CCD camera alignment *electrical test * unload * sort of pass, opens, shorts, and alignment errors.The GATS-2100 concurrent approach provides unmatched volume capability... 2.5 seconds per device. As with all Nidec-Read Test systems, the GATS-2100 offers you the most test technologies for your requirements
-
product
1 Mm Calibration Kit
85059B
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
product
4-In-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (f) 50 Ohm
85519A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
product
Short Buddy® Audible Trouble Shooter
230
Short Buddy helps you find the short! This unique tool connects at the fuse panel and becomes in series with the test circuit. A system of audible beeps helps you find the problem and permit hands free troubleshooting. Have a dead short? Short Buddy gives you continuous re-set/re-power capability, a real time saver. While you push, pull, tug and grab wires, Short Buddy is always watching the current level. If your tug causes the dead short again, Short Buddy opens the circuit for 10 seconds, then re-applies power to the circuit. Re-powering the circuit can also be done manually.
-
product
Stand Alone Low Voltage Testers
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
product
Motor Winding Ohmmeter
RMO-M Series
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
product
Audio Circuit Tester
25500
Handy device for locating short and open circuits. Horn sounds when circuit is complete. Long 5 foot leads permit technicians to work around corners, under dash boards and in trunks. For use on all 6 and 12 volt circuits.
-
product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-253-010
The 40-253-010 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Loop A Line
TX916
The Loop a Line has been a Telstra standard for 20 years. It is probably the simplest time saving device available for contractors and technicians. Once fitted to the far end of a line you can switch between Open, Short, Connect, 600 ohm, and Tone modes allowing all installation and fault location to be performed from the one end without having to go back and forward from one end of the line to the other.
-
product
DataComm & LAN Testers
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
SignalShark® - Real-Time Outdoor Remote Analyzer
Real-Time Outdoor Remote Analyzer for the Detection, Analysis, Classification and Localization of RF Signals between 8 kHz and 8 GHz. Supports automatic direction finding and localization via AoA and TDOA. For fixed installation or semi-static use on demand. Solves complex measurement and analysis tasks reliably and quickly with outstanding RF performance. Windows 10-based open platform for third-party applications. The "SignalShark 3330 Outdoor Unit" series is characterized by a robust and weatherproof die-cast aluminum housing with IP65 protection class, which is also used as a heat sink. The compact size allows the receiver to be mounted close to the antennas, keeping the antenna cables short and the resulting sensitivity high.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16 (female)
85038F
The Keysight 85038F calibration kit contains only female calibration devices (open circuit, short circuit and termination) and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 122Ω
40-253-112
The 40-253-112 is a programmable resistor module with 1 channel which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 122Ω
40-251-112
The 40-251-112 is a programmable resistor module with 4 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
6-12V Heavy Duty Circuit Tester
1671
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems.1. Locate short, ground or open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start system.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
40-203-002
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
An IEC 61000-4-11 Full Compliance Voltage Dip SimulatorModel: VDS-2002
VDS-2002
NoiseKen's new VDS-2002 offers easy and accurate test and following features: Dip, swell, interruption and variation tests up to 16A 240V single-phase AC, interruption test up to 125V DC, preset levels 0%/40%/70%/120%, open and short mode selection for interruption and optional Windows software.
-
product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
6GHz SMA Calibration Kits
CAL-SMA-6B
The CAL-SMA-6B Basic calibration kit provides the elements for performing Open–Short–Load and Through calibrations for one and two port VNA measurements.
-
product
Multi-Modular Cable Tester
MT-7051N
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 239Ω
40-252-113
The 40-252-113 is a programmable resistor module with 2 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Cable Locator
A cable locator can locate open power cables, either live or without current, with voltages up to 300 V. A cable locator can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested. Many cable locator devices also can locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
Network Tester
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
