Filter Results By:
Products
Applications
Manufacturers
-
product
Electrochemical (Molecular Electronic Transfer) Motion Sensor transducers
The Molecular Electronic Transfer Technology
The basic design of the MET transducer, shown in Figure 1. The transducer is contained in a channel, 1, of a sensor filled with a specially prepared electrolytic solution. It consists of four fine platinum mesh electrodes, two anodes, 2, and two cathodes, 3, separated by thin, microporous ceramic or polymer spacers 4. Such an assembly is held together by a housing 5. To measure the motion of the fluid, it must be converted into an electrical signal. One way of achieving this is by using the convective diffusion of the ions in the electrolyte. At the heart of a MET device are inert electrodes at which a reversible redox reaction occurs, which does not involve either plating of a metal or evolution of a gas.
-
product
Transceiver Testing
Family of RF test systems designed for transceiver testing. Designed for radio-to-radio testing in a closed mesh network. Step attenuators allow you to dynamically fade up/down the RF signal between radios. These Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted remote commands.
-
product
Screen Tension Tester
Guangzhou Amittari Instruments Co.Ltd
Screen Tension Tester applicable to general wire mesh tension and steel mesh tension measurement. Suitable for screen printing and screen stencil measurement, high accuracy. The ideal and necessary tool for production of precise screen and steel mesh.
-
product
AdvancedTCA, Type 11A, 13U 19" Vertical, DC
11A14FGCD8Y4VNXX
Elma's ATCA, DC, 13U vertical enclosures with backplane 14-Slot Dual Star or Mesh backplane, shelf management, and options. PEMs with availability (99.999%). 19" rackmount vertical ATCA chassis for carrier-grade applications.
-
product
Networking Solutions
Thread
Thread is an IPv6-based mesh networking protocol designed as a reliable, low-power, secure, and scalable networking solution for connecting Things to the IoT. As a founding board member of the Thread Group, Silicon Labs helps accelerate time to market with proven mesh networking hardware and software solutions.
-
product
Lightening Protection
Copper Grounding
LBA offers a complete selection of copper bare wire and strap of various widths and gauges for grounding system construction. Our offerings include prefabricated copper ground wire terminations, Copperweld™ ground rods, chemical ground rods, earthing mesh, and exothermic welding materials, as well as UL and NFPA compliant lightning system cable and accessories.
-
product
Fleet Management System
PBE Fleet
PBE FLEET, our industry leading Fleet Management System (FMS) extracts, records and presents crucial operational data for the monitoring and management of a mining fleet. This enables all levels of the mining operation to have the knowledge to support quick and effective decisions.PBE FLEET is a suite of specialized software modules running on a rugged Nexis computing platform, which is installed on-board the mining fleet with GPS and wireless mesh capabilities. Nexis links on-board vehicle systems back to the office for real-time management of your fleet. Operators engage through the in-cab screens.
-
product
Rebar Locator
Profometer PM-650 AI
The Profometer PM-650 extends the measuring modes of the Profometer PM-630 with the unique Cross-Line Mode and further analysis functions. The Cross-Line Mode allows users to measure the rebars of the first and second layer typically arranged in a rectangular mesh.
-
product
ATCA 5U 16 Slot Mesh
1900001495-0000
The 5U 16-slot ATCA backplane is a Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
6U OpenVPX 6 Slot Profile BKP6-DIS06-11.2.18-3
1OVX606MZ3-1X01R
VPX mesh, 4 lane Fat Pipe, QFP expansion plane, up to 6.25 Gbps per channel.
-
product
Software Modules for Smooth, Freeform CAD Surfaces in Verisurf Reverse
Verisurf Quick Surface
Quick Surface is a powerful option for Verisurf Reverse that efficiently creates smooth, high-quality surfaces from meshes derived from scan data or STL files. Quick Surface maintains curvature continuity between adjacent surfaces and is ideal for creating smooth, high-speed toolpaths.With Quick Surface, it’s a snap to produce freeform CAD surfaces from organic or prismatic Verisurf meshes and assess the surface-to-mesh fit quality prior to export for additional, downstream modeling or other processing. Quick Surface is an ideal enabler for scan-to-part or scan-to-3D-printing workflows.
-
product
3U CompactPCI Serial 8-slot SSL w/o RTM w/ Ethernet
1CPCIS-308-L200
3U CompactPCI Serial Backplane with 8 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 7x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh
-
product
ATCA 5U 4 Slot replicated Mesh - dual shelf managers
109ATCA504-3000R
The 5U 4 slot ATCA backplane is a replicated Mesh with dual shelf managers. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
product
Sensor Placement & FEA Analysis
GageMap - GM
APEX Turbine Testing Technologies
Apply strain gages and accelerometers to your finite elementmodel independent of the mesh anywhere you want, or letGagemap do it for you.
-
product
3U OpenVPX 6 Slot Profile BKP3-DIS06-15.2.14-3
1OVX306SX6-1X11R
Distributed mesh, no expansion plane, 2x control planes, Gbaud rate to 6.25, 3U, 6 Slots.
-
product
QW-AddIn For Autodesk® Inventor® Software
QW-AddIn for Autodesk® Inventor® Software is a QuickWave plug-in for Autodesk® Inventor® Software, a wide-spread mechanical tool, allowing defining a complete project for electromagnetic simulation, also periodic structures and axisymmetrical structures (V2D), directly in the popular CAD environment. A set of self-explaining dialogues provides very convenient tool for setting the electromagnetic properties such as assigning the materials, adding ports, boundary conditions, setting postprocessings and excitation parameters.Automatic mesh generation using Automatic Meshing Intelligent Generation Option (AMIGO) optimises the meshing taking into account requested wavelength resolution in all media, while avoiding unnecessarily small cells. Additionally QW-AddIn for Autodesk® Inventor® Software can be used for optimisation and parameters sweep with QW-OptimiserPlus.QW-BHM is available and heating parameters can be defined together with rotation in XY plane along axis parallel to Z axis. Creating proper axis of rotation can be done by selecting edge or solid body from the project. It will contain the middle point of selected object and its location can be modified either with the mouse or by entering new coordinates.
-
product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
product
PCB Systems Vibration and Acceleration Simulation Solution
Xpedition
As the industry’s market share leader in PCB design software, the Mentor Graphics® Xpedition product augments mechanical analysis and physical testing by introducing virtual accelerated lifecycle testing much earlier in the design process. This is the industry’s first PCB-design-specific vibration and acceleration simulation solution targeting products where harsh environments can compromise product performance and reliability, including the military, aerospace, automotive and industrial markets. Traditional, physical HALT (highly accelerated lifecycle testing) is conducted just before volume manufacturing, and requires expert technicians, which can result in costly schedule delays. Bridging mechanical and electronic design disciplines, the Xpedition product provides vibration simulation significantly faster than any existing method. This results in increased test coverage and shortened design cycles to ensure product reliability and faster time to market. The Xpedition component modeling library is the most extensive in the industry, comprised of over 4,000 unique 3D solid models which are used to create highly defined parts for simulation. The 3D library allows users to easily match geometries to their 2D cell database. Designers can assemble the parts models on board and automatically mesh them for performance analysis, including stiffeners and mechanical parts. The system modeling tool is ultra-fast since it can model over 1,000 components per minute.
-
product
3U CompactPCI Serial 4-slot SSL w/o RTM w/ Ethernet
1CPCIS-304-L200
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh
-
product
RF Shielded Test Enclosure, Largest Rack Mountable Enclosure
JRE 1724
Originally designed for testing wide screen laptops, the rack-mountable JRE1724 is ideal for large wireless devices such as; Mesh Network AP's, Cellular/LTE/4G Base Stations, and other large RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble free operation over its lifespan. Internal struts keep the lid open for easy internal access when connecting the device under test.
-
product
3U CompactPCI Serial 5-slot SSL w/ RTM w/ Ethernet
1CPCIS-305-L210
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 5, Ethernet full mesh.
-
product
5-Zone Lead-Free Convection Reflow Oven Includes Pin-Over-Mesh-Belt Conveyor
CR5000
The CR5000 full-convection reflow oven provides consistent, quality performance, low ΔTs across every board, and mid-volume throughput, all in a compact, floor-space-saving footprint. The oven also provides flexibility and easy setup and changeover, thanks to the generously sized pin-edge and mesh belt conveyors, easy to use oven management software, and easy profile setup with the included KIC Auto Focus profile prediction software.
-
product
3U CompactPCI Serial 4-slot SSL w/ RTM w/ Ethernet
1CPCIS-304-L210
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 2 to 4, Ethernet full mesh
-
product
ATCA 5U 6 Slot Mesh
109ATCA506-300XR
The 5U 6-slot ATCA backplane is a 3X Replicated Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
DataNet Wireless Data Loggers
The DataNet wireless system is a data acquisition solution developed for 24/7 real-time monitoring for mission critical organizations. Boasting a variety of wireless data logger models using ZigBee RF technology, the DataNet solution is capable of measuring parameters such as temperature, relative humidity, voltage, current, or frequency. Choose from DataNet models offering up to 6 inputs or the more cost-effective single or dual input Mini DataNet range, depending on your application requirements. Each DataNet mesh network is managed by a Receiver connected via USB to a Windows-based PC, and also supports addition of wireless Repeater units for extending the network transmission range and improving network robustness.
-
product
Adaptiv™
Adaptiv™
Adaptiv™ provides the lowest ownership cost of any AMI provider. By using advanced mesh technology and robust public cellular communications, Adaptiv™ puts AMI within reach of any municipal or electric utility.
-
product
Mesh Filters From 0.9 To 15 THz
Insight Product Company offers Mesh Filters from 0.9 to 15 THz
-
product
GPON ONT
ONT-2GE-V-RFDW
Hangzhou Softel Optic Co., Ltd.
2GE+1POTS+WiFi+CATV GPON/EPON HGU WiFi Mesh terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators. These boxes are based on the mature Chipset (Realtek) technology, which have high ratio of performance to price, and the technology of IEEE802.11b/g/n/ac WiFi, Layer 2/3, Wi-Fi EasyMesh,and high quality VoIP as well. Support full management of HGU devices through SOFTEL OLT. They are highly reliable and easy to maintain, with guaranteed QoS for different service. And they are fully compliant with technical regulations such as IEEE802.3ah,ITU-T G.984.x and technical requirement of GPON Equipment from China Telecom.
-
product
3U CompactPCI Serial 3-slot SSL w/ RTM w/ Ethernet
1CPCIS-303-L210
3U CompactPCI Serial Backplane with 3 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 2x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 3, Ethernet full mesh.
