Filter Results By:
Products
Applications
Manufacturers
Mains
chief conduit of electricity, gas or water distribution.
-
product
Signal Analysis
Harmonic Distortion Analysis
The software is used for automatic measurement of the harmonic distortion factor and voltage r.m.s. of signals coming to the input channels of FFT spectrum analyzers. Adjustment to the frequency of the main component is performed automatically. The program is based on the measurement of the voltage r.m.s. of higher components by an external or internal reference signal.
-
product
Fully Automatic Transformer Winding Resistance Tester
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
product
LAN Tester
TVR10/10/100
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
product
Radiating Loops
The magnetic, handheld coil was designed to generate defined mag-netic fieldstrength in the frequency range from DC up to 5 (7) MHz. The main application is immunity testing against magnetic fields.
-
product
Beam Directional Power Supply Mains
SiteX CP200D
Being just 20 mm longer than the CP160D, the CP200D represents the best compromise between high penetration (up to 42 mm for steel) and the capacity of the generator to fit with various NDT applications, such as inspections of more technical materials in the aeronautical or space industries. The CP200D is one of the most versatile generators on the market and thanks to its built-in multiple X-Ray output carrousel it will adapt to a very wide variety of NDT applications, without compromising in any manner its light weight (12 kg) and ease of use.
-
product
Soil Mechanics
INSITU
The INSITU program interprets statical and dynamical geotechnical in situ tests. In order to interpret the SPT tests, the program utilises the main correlations that are normally used to determine the geotechnical parameters of a soil. One should enter the geometrical and geotechnical parameters pertaining to the stratigraphy surveyed trough drilling and the number of blows relative to each test; some corrective parameters can be entered that enable one to limit the perturbations in the interpretation of the data caused by the way the test is performed and the type of instrument that is used.
-
product
HandyScope HS4: 25 MS/s 100MHz BW, 4 Channel, USB Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-25
The Handyscope HS4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels. The HS4 has just like it's predecessor the four main measuring instruments: a Multimeter, an Oscilloscope, a Spectrum analyzer and a Transient recorder.
-
product
Land True-Inertial Navigation
Geonyx™
Geonyx™ family is designed for three main applications:- Navigation- Target geolocation- Artillery pointing Capable of operating under extreme conditions and in a full GNSS denied environments, Geonyx™ is highly reliable.- Pointing accuracy < 0.5 mils thanks to HRG Crystal™ technology- Quick & flexible alignment in GNSS denied environment- The most compact, robust & reliable on the market and hard-mounted
-
product
PXI Single 4x4 1-Pole 10A Power Matrix
40-551-003
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
LPR Meter
This instrument is at home on the laboratory bench or out in the field. Provided with an internal lead-acid battery and mains charger the LPR Meter is a truly portable corrosion monitoring system. Using the well proven and liked method of Linear Polarisation Resistance to determine the corrosion rate the instrument is ideal for day to day testing.
-
product
Cable Tester
KT-468
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
product
Surface Resistance System Kit
PRS-801RM
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
3D Geo-Magnetometer
For the measurement of magnetic equilibria such as the earth's magnetic field, for the determination of anomalies and biologically active location factors. Three highly sensitive magnetic field sensors, as well as a dedicated microprocessor, are integrated into the measuring probe. The sensitive magnetic field sensor is connected to a PC, notebook or laptop (not included). The main features in brief:
-
product
Three-Phase Relay Tester
PTE-300-V
The equipment compromises of three independent output channels than can be selected as voltage or current. This enables the unit to be used as a complete single-phase equipment (Voltage, Current, and phase angle between them), or with channels synchronized, as a three phase voltage or three phase current generator from a single phase mains input. The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability.
-
product
EMI Test Receiver
KH3938B
Beijing KeHuan Century EMC Technology Co,.LTD
Is a fully automatic radio disturbance test receiver and is the main tool for EMI testing. KH3938B receivers frequency range 9kHz-1GHz, in accordance with: 2010 and GB / T6113.101-2016 development standards designed to meet the requirements of the standard-compatible, can be used to power emission test, Sao conduction disturbance voltage test, radiated disturbance within 1G test. The receiver has the advantages of fast test speed , strong maneuverability, stable performance, and convenient test data processing.
-
product
Network Cable Tester
AVJoG
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
product
Smartcard Interfaces
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
product
Hydrogen Frequency & Time Standard
CH1-1033
The hydrogen frequency and time standard Ch1-1033 is designed for precision storage and reproduction of the size of frequency and time units as part of measures and reference complexes. Main areas of application: – public service of time and frequency; – ground control complexes of radio navigation systems; – radio interferometry with extra long base.
-
product
Video Signal Generator
MSPG-7800S
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneousl and sufficiently examining a large-sized display device.
-
product
Robotic Intelligent Laboratory System
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is able to determine calorific value, total sulfur, internal moisture, ash, volatile matter, CHN content and other indicators by robot technology. The main components include intelligent robot, automatic analytical instruments (calorimeter, sulfur analyzer, proximate analyzer, and elemental analyzer), automatic bottle opener and sampling device, automatic weighing device, oxygen vessel loading and cleaning device, electrical control system, and laboratory analysis and data management software.
-
product
3D Sensors (Main Screen)
surfaceCONTROL
surfaceCONTROL sensors are used for 3D measurements and surface inspections. The sensors use the fringe projection principle to detect diffuse reflecting surface and to generate a 3D point cloud. This point cloud is subsequently evaluated in order to recognize geometry, extremely small defects and discontinuities on the surface. Sensors with different measurement areas are available. This enables the inspection of the finest of structures on components as well as shape deviations on large-area attachments. Powerful software packages are available for evaluation and parameter setting.
-
product
Multivariable Transmitters
The Multivariable transmitter measures and calculates the mass flow as a function of differential pressure DP as well as absolute pressure and the temperature. Therefore it should be used whenever DP flow measurement needs a compensation of temperature and pressure. The main advantage is to have just one single device in the field instead of several transmitters and a mass flow calculator.
-
product
Clean Power Source
AC1000A
The AC1000 achieves its unique price/performance ratio by actively adjusting the incoming mains waveform to produce a clean output. Other suppliers use convertor techniques to completely recreate the output from scratch. Our solution delivers an output which achieves the required THD with the minimum of hardware and expense. It includes the ability to switch the correction in or out so that the original waveform can be observed and measured if required. Overload and thermal protection systems are built-in and produce an audible warning if activated.
-
product
Open Loop Current Sensor
C03 50A
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in systems for industry and commerce as well as in communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
product
Scalable Tester System for Functional Testing
UTP6010
The UTP6010 is a scalable tester system for functional testing, comprising an integrated main switching unit, a keyboard drawer and a swivelling monitor. It is the reliable, modular, low priced UTP starter kit. The system is suitable for tester applications, where space-saving devices are required, because its construction height is only 12 HU (excluding keyboard drawer and main switching unit).
-
product
Accessory for Test Chest 3G Facilitating 'EYE' Analysis
EYE~POD
Designed to interface with Murraypro's Test Chest 3G, the EYE~POD accessory module extends monitoring capability to include SDI envelope parameters from SD through to 3G. Users receive immediate visual indication of the quality of an SDI input signal with regard to both overall signal amplitude and Jitter. Drawing power from TC3G, the coupled-combo may be used on local battery power, or supported with an external mains PSU
-
product
2nd Generation PCI Multi-function Decommutator
LS-50-D
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
-
product
Digital Circuit Breaker Analyzer
CT-7000 S3
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
product
SOI Bonding Systems
An accurate wafer bonding process is the key factor in obtaining high quality single crystalline silicon films on insulating substrates. The EVG850 SOI/Direct Wafer Bonding systems are designed to fulfill a wide range of fusion/molecular wafer bonding applications, with main focus on SOI substrates manufacturing. Ultra clean handling of wafers throughout the bonding process assures high-yield and void-free bonds. All essential steps, from cleaning and alignment to pre-bonding and IR-inspection are combined in one high volume production system. EVG850 is the only production bonding system built to operate in high throughput, high-yield environments and guarantees void-free SOI wafers up to 300 mm.The EVG300 series single wafer cleaning systems are designed for efficient removal of particles. In semiconductor processing, efficient cleaning and particles removal prior to critical process steps enables maximum yield. Wafer Bonding is a process which is strongly affected by particles: each particle on the wafer surface produces a void orders of magnitude larger than its diameter, contributing to a dramatic yield loss.
-
product
Breakout Box and Data Logger
1U643-001
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
