Filter Results By:
Products
Applications
Manufacturers
Host
-
product
High-Speed Embedded Host Electrical Test Board
HSEHET
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
product
Communications Module
CC02A
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
product
PC104Z with FMC Board
PC104Z
Sundance Multiprocessor Technology Ltd.
PC104Z is based on the Xilinx Zynq UltraScale+ MPSoC family. This hardware is in PCIe104 form factor and adheres to its latest specification. It offers 4 Gen 2.0, x1 lane PCIe interfaces through a switch which allows 4 PCIe104 cards to be connected to the ARM on the Zynq which acts as the host. The board also offers 2 Gen 4.0, x4 lane PCIe connected to the PL parts which can act both as host and end points. The additional interfaces offered by this card can be seen under the Features tab.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCI Express A/D Board
AD14-400 Series - Dual 14 bit, 400 MS/s
The AD14-400 series has two 20-400 MS/sec 14-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 3.2GB/sec (400MS/s * 2 bits per sample * 2 channels). Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
product
ADC & DAC PCIe Card Powered by RFSoC
iW-RainboW-G42P®
AMD Xilinx’s ZU49/39/29DR Zynq Ultrascale+ RFSoCRAM Bandwidth8GB, 64bit DDR4-2400 RAM with ECC for PS8GB, 64bit DDR4-2666 RAM for PL (Expandable)16 DAC channels through SMA connector upto 10Gsps16 ADC channels through SMA connector upto 2.5Gsps3/4 Length PCIe Gen3 x8 Host InterfaceIntegrated ultra low-noise programmable RF PLIntegrated SyncE & PTP Network SynchronizationNVMe PCIe Gen2 x2/x4 M.2 ConnectorFMC+ HSPC Connector
-
product
FPGA Image Processing (IP) Development Kit
ProcVision
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
-
product
1.3 MP Global Shutter Camera (Monochrome / Color (RAW Bayer))
See3CAM_10CUG
The See3CAM_10CUG is a 1.3 MP Custom Lens CMOS USB Global Shutter Camera Module. This is a S/CS/C Mount global shutter camera and is UVC-compliant SuperSpeed USB 3.0 Camera. It is based on the Aptina / ON Semiconductor AR0134 CMOS sensor. See3CAM_10CUG is also backward compatible with USB 2.0 host ports and does not require any special camera drivers.
-
product
Ethernet
Ethernet, arguably the most common communication protocol on the planet, continues to spread into new markets and incorporates new protocols; it presents today’s Ethernet engineers with host of new test and validation challenges. Specifically, the increasing adoption of lossless Ethernet standards like FCoE, RoCE, and NVMf and increases in the line-rates of Ethernet from 10GbE and soon to 100Gb/s to name a few.These new physical and logical communications standards have exposed legacy test tools as outdated and incomplete for Ethernet product developers and the ecosystem. Teledyne LeCroy is addressing these needs by leveraging our extensive experience in high-speed serial data analysis tools currently used by many of the same companies developing products for NAS, SAN, LAN, and other high-speed protocol environments.The SierraNet Family of Ethernet test platforms provides best in class traffic capture, analysis, and manipulation for testing physical link characteristics and application operations. SierraNet is designed for addressing today’s high-speed storage and communications network problems and compliments other tools offering industry leading visibility and utility.
-
product
LIN Interface Device
LIN Interface Devices are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. LIN Interface Devices work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PCI Express Image Acquisition Frame Grabber
Xcelera-HS PX8
The Xcelera-HS PX8 has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
product
USB Cable
143556-0R3
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
product
AMC For PCIe Bus Expansion
AMC113
AMC113 is VadaTech second generation PCIe expansion module. The AMC113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s other carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem.The AMC113 allows expansion among multiple μTCA chassis or
-
product
6U Dual 64/100 PMC VME Carrier
V2PMC2
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
product
AdvintRIO™ Reconfigurable I/O
PIRANHA
The Piranha platform employs a NI single board RIO (sbRIO), NI C Series I/O modules, and custom circuitry. Piranha systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to a powerful real-time controller and high performance field-programmable gate array (FPGA) and up to two (2) C Series I/O modules. It provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These controllers are designed for ruggedness, reliability, and low power consumption. The heart of Piranha system is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module. Multiple units can also be daisy changed together for larger applications.
-
product
In-System Test Programming System
WriteNow
Based on proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices from various manufacturers and have a compact size for easy ATE/fixture integration. They work standalone or connected to a host PC, and are provided with easy-to-use software utilities.
-
product
Dry Film Thickness
Dry film thickness, coating thickness or paint thickness as it is often known, is probably the most critical measurement in the coatings industry. It provides vital information as to the expected life of the substrate, the product’s fitness for purpose, its appearance and ensures compliance with a host of International Standards. In 1947, Elcometer launched one of the world’s first non-destructive coating thickness gauges, the Elcometer 101 Coating Thickness Gauge. For more than 6 decades, the design and production qualities of this rugged and reliable instrument have been the watchwords for all our products and these philosophies are still held today. Elcometer has a comprehensive range of Dry Film Thickness gauges to meet all of your coating inspection requirements.
-
product
ATCA I/O Rear Transition Module (RTM)
ART001
The ART001 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe and Management I/O for the front blade. The module is designed to mate with any ATCA Carrier. ART001 provides PCIe x8 access via an iPASS connector to the rear. The GbE rear access is provided via six SFP ports and five RJ-45 ports. The module has dual 10 GbE PHY which mates to the host via the zone 3 connector and provides dual SFP+ to the rear.
-
product
Wireless Electronic Flight Bags
webFB
The ultra-compact webFB easily fits in the palm of the hand, yet incorporates the capabilities of both an AID and a wireless server. The built-in AID safely gathers essential data from the aircraft's ARINC 429 and 717 databuses and conveys it to custom software or EFB apps hosted on the internal server. Using a wireless connection to portable EFB tablets, the webFB securely delivers this valuable information right to the fingertips of the flight crew.
-
product
cRIO-9066, 667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 8-Slot CompactRIO Controller
783169-01
667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 8-Slot CompactRIO Controller - The cRIO-9066 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. Additionally, the cRIO-9066 features an SDHC slot and a variety of connectivity ports, including one tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
USB to I2C Adapter
Model JI-300
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
product
Transceiver Driver
S-112
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
product
Laser Calibration System, Superior Accuracy, Portability and Reliability
5530
The configurable system offers all the components you need to perform a variety of measurements using the USB on your PC as the host controller and power source. For basic linear measurements you will need the USB Axis Module, USB Sensor Hub, Air and Material Sensors, Sensor Cables, Software, Laser, Laser Cable, Remote Control (optional)and the Linear Optics Set. Other available options include the Laser Tripod (with laser mounting plate), optics and fixturing kits for making additional types of measurements, and wheeled transit cases.
-
product
12-Port PCI Express
PEX 8748
The ExpressLane™ PEX 8748 is a 48-lane, 12-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8748 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
product
PMC-ExtendIO-II
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
product
Multi-Protocol Card
EXC-4000PCI
The EXC-4000PCI/xx card for the PCI bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words.The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
product
Chassis Remote Control Cable
The Chassis Remote Control Cable connects the PXI Remote Control Module to a variety of host interfaces on desktop PCs, rack-mount controllers, laptops, or other PXI or PXI Express systems.PXI Remote Control Modules support either copper cabling or fiber-optic cabling, and some models support both. Copper cables offer higher data throughput capability but are generally shorter (1 meter to 10 meters), while fiber-optic cables are available in much longer options (100 meters or more) but may have lower data throughput capability.
