Filter Results By:
Products
Applications
Manufacturers
Frame Grabbers
Digitize and record a single frame of video information.
-
product
PCIe-1437, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Device
785605-01
The PCIe-1437 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe-1437 includes an onboard FIFO for higher bandwidth use cases, and it works with any base‑, medium-, and full-configuration Camera Link camera. The PCIe-1437 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe-1437 also supports Power over Camera Link (PoCL) and can power cameras through PoCL-enabled cables.
-
product
2/4-CH PCI Express® GigE Vision PoE+ Frame Grabbers
PCIe-GIE7x Series
- Hardware Trigger over Ethernet with Action Command- Up to 120W PoE power from PCIe bus/4-pin/6-pin Molex connector- PCI Express® x4 compliant- IEEE 802.3at for PoE+ (Power over Ethernet Plus)- PoE protection and automated power budget control for enhanced asset protection- Easy-to-use utility and API provided for PoE power management- Multiple cards, multiple cameras, in a single system- Wide operating temperature range from 0°C to +70°C supporting non-drop frame capture in extreme environments
-
product
FireBird CoaXPress Frame Grabber (4xCXP12-3PE4)
AS-FBD-4XCXP12-3PE4
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees high speed and low latency image data transfers and zero CPU intervention.
-
product
Phoenix LVDS Frame Grabber (PE1)
AS-PHX-D36-PE1
Phoenix-D36 is a PCI Express board for the acquisition of digital data from a variety of sources, including digital frame capture and line scan cameras. It has 36 bits used for input data, with 4-bits for control. This provides support for a single 12 bit RGB or 32 bit mono data source, including multi-tap cameras. The 4-bit control inputs are dedicated as Frame Enable, Line Enable, Data Enable and Pixel Clock.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
Low-cost, Full-Featured Video Frame Grabber Board
Aexeon
DescriptionAexeon is a low-cost, full-featured video frame grabber board for analog camera solutions. Aexeon accepts multiple composite, S-Video, or component video inputs in both NTSC and PAL formats and digitizes in both square pixel and CCIR-601 resolutions. With on-board processing, complete camera control, and video output, Aexeon is the perfect product for analog camera OEM solutions.
-
product
PCI Express 4-Channel Frame Grabber with Audio Capture
811
4 composite/S-Video + 4 stereo audio input channels Simultaneously captures on all channels Captures raw RGB or YUV video 4 general-purpose digital I/Os configurable as inputs or outputs
-
product
FireBird CoaXPress Frame Grabber (Quad CXP-6)
AS-FBD-4XCXP6-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Frame Grabbers
Active Silicon designs and manufactures a wide range of acquisition solutions based around leading-edge hardware technology and versatile software toolkits. The range includes acquisition solutions for CoaXPress, Camera Link, HD-SDI, SDI and LVDS in different form factors. Operating system support includes 32/64-bit versions of Windows 7/Vista/XP, Linux, QNX, and Mac OS X.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
product
USB MPEG Frame Grabber
2251
MPEG1/2/4 and JPEG capture to USB from an analog video source at D1 resolution Compact form factor for embedded designs 30 fps NTSC, 25 fps PAL Synchronous audio capture from a line level (stereo) input Multiple region motion detection Text overlay (OSD) SDK works with multiple units
-
product
ATX Motherboard With LGA1151 Socket 8th Gen Intel® Core™ Processor, Intel® Q370, USB 3.1 Gen2, SATA 3.0, Dual LAN, VGA, DisplayPort, DVI-D, And HDMI
IMB520
The IMB520 is powered by the LGA1151 socket 8th generation Intel® Core™ i7/i5/i3, Pentium® or Celeron® processor (code name: Coffee Lake) with the Intel® Q370 chipset. The ATX motherboard supports four 288-pin DDR4-2666/2400 DIMMs with up to 64GB of system memory. The Intel® Coffee Lake-based IMB520 is a performance-driven motherboard that is expandable, feature-rich and versatile to help facilitate quick deployment. The brand new IMB520 is an ideal solution for automation, transportation, retail, medical and other Industrial IoT-related applications. The IMB520 provides one PCIe x16 slot, four PCIe x4 slots, one PCIe x1 slot and one PCI slot for frame grabbers, motion control cards and edge-based data acquisition cards, making it an ideal solution for machine vision and industrial automation application. It also has two USB 3.1 Gen 2 and four USB 3.1 Gen 1 ports for faster data transfer. In addition, the industrial-grade ATX motherboard is integrated with the Intel® HD Graphics for superb visual performance. Up to three independent displays are available from DisplayPort, DVI-D, HDMI, and VGA.
-
product
Camera Link Breakout Box
CLB-501B
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
product
FireBird CoaXPress Frame Grabber (Dual CXP-6)
AS-FBD-2XCXP6-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Phoenix LVDS Frame Grabber (PE4)
AS-PHX-D36-PE4
Phoenix-D36 is a PCI Express board for the acquisition of digital data from a variety of sources, including digital frame capture and line scan cameras. It has 36-bits used for input data, with 4-bits for control. This provides support for a single 12-bit RGB or 32-bit mono data source, including multi-tap cameras. The 4-bit control inputs are dedicated as Frame Enable, Line Enable, Data Enable and Pixel Clock.
-
product
Framegrabber
FastX-UXGA
The FastX-UXGA frame grabber series is for users who anticipate a demand for extreme I/O requirements or higher bandwidth, complex image processing and real-time fast storage in a cost effective platform. The base Fast-UXGA, is a raw-length PCI board with two (four-muxed) UXGA analog conversion channels using Analog Device's AD9888. The front end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, from zero to four PNX1702 processors before output. Finally, the Fast-UXGA interfaces to the host computer through a 4x PCIe interface for state-of-the-art data acquisition.
-
product
Multi-Interface Frame Grabber
Xtium2 CLHS FX8 LC
The Xtium2-CLHS FX8 LC supports up to two bidirectional SPF+ modules running at 10Gbit/s. Using CLHS X-Protocol, the Xtium2-CLHS FX8 delivers up to 2.0 GB/s of image acquisition and 6.8 GB/s to host memory. The low-cost SPF+ module and fiber optic cables help extend cable lengths to 100 meters.
-
product
Cameras
Machine Vision
Capture the power of Phantom High Speed imaging in machine vision streaming applications. Image data flows directly to a frame grabber and PC or long record DVR via CXP protocol. Data is immediately accessible and limited only by the amount of storage in the PC or DVR.
-
product
Frame Grabbers
Domino Series
The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. They support any system function associated to industrial acquisition, such as camera asynchronous reset, exposure and strobe control. The latest Domino boards - Melody, Harmony and Symphony PCIe - are based on an innovative proprietary technology called D Technology*. It provides a perfect digital image with the benefits of a proven analog environment: low-cost, reliable cabling and connections, smallest cameras, low power,
-
product
2-port/4-port PCI Express GigE Frame Grabber Card
AX92320
The AX92320 supports PCI Express x4 lane, two or four independent Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports and GigE Vision camera compliance. The PCI Express x4 frame grabber can provide up to 30 watts at 54 VDC power to port which allows power to be supplied to connected PoE-based devices, such as GigE Vision cameras in machine vision systems. The intelligent GigE Vision card also supports IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition. Combining IEEE 1588 and PoE function, the card utilizes a single Ethernet cable for power, data, and synchronization. Furthermore, it supports jumbo frames up to 9.5KB. The AX92320 is ideal for PoE applications such as automated optical inspection (AOI), factory automation, and PC-based surveillance systems.
-
product
Frame Grabber/ Video Capture Cards
- Full product line support, including analog, GigE Vision, IEEE 1394b, Camera Link, HDMI, and 3G-SDI- Compatible with most popular cameras and software- Carefully selected embedded components ensure long term availability- Highly integrated with ADLINK I/O cards and embedded computing platforms
-
product
Solution for High Density I/O Applications
BitBox
The BitBox is BitFlow''s new solution for high density I/O applications. Many machine makers require a large number of computer managed I/O signals for continuous control of the system state. This means controlling devices such strobes, solenoids, actuators, indicators etc. as well as gathering inputs from photo-detectors, switches, encoders and triggers. In general, BitFlow frame grabbers come with a fairly large number of inputs and outputs, but for some system this is simply not enough. Most customers end up purchasing another device to manage the I/O, which adds expense, requires another slot, another driver and SDK, another manual, etc. The BitBox has been designed for just this situation. It is controlled completely from the frame grabber, uses the same API, driver and manuals as the frame grabber. This saves time, money, space, and learning curve.
-
product
CL PX4 Dual Frame Grabber
Xcelera-CL PX4 Dual
Building on the field proven technology and performance of Teledyne DALSA’s X64 frame grabbers the new Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. The PCIe host interface is a point to point host interface allowing simultaneous image acquisition and transfer without loading the system bus and involving little intervention from the host CPU. The X64 Xcelera-CL PX4 Dual is a highly versatile PCIe frame grabber capable of acquiring images from two independent Camera Link™ Base cameras and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 Dual an ideal solution to a wide variety cost-sensitive applications.
-
product
Base/PoCL Camera Link frame grabber
Neon-CLB
Simplify your industrial, medical, or semiconductor imaging application with BitFlow's Neon-CLB, the easiest to use and most reliable Base/PoCL Camera Link frame grabber available anywhere. The Neon-CLB captures images at up to the camera's highest frame/data rate, with precision image acquisition suitable for the most demanding applications.
-
product
PCI Express Image Acquisition Frame Grabber
Xcelera-HS PX8
The Xcelera-HS PX8 has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
product
FastCamera
FC200
The FastCamera 200 is a high-speed 2 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
CL+ PX8 Full Frame Grabber
Xcelera-CL+ PX8 Full
The X64 Xcelera-CL+ PX8 Full has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
product
PCIe-8239, 4-Port, GigE Vision Frame Grabber Device
787790-01
The PCIe-8239 features Power-over-Ethernet (PoE) technology. It provides optimized performance of high-resolution and high-frame rate cameras through the combination of independent Gigabit Ethernet ports and the high-performance GigE Vision driver software. PoE reduces the need for additional external power supplies by powering cameras over the Ethernet bus, which simplifies system design and cabling complexity.
-
product
Frame Grabber Device
The Frame Grabber Device is designed for machine vision and scientific applications requiring high-resolution and high-speed digital imagining. They offer a range of features including onboard programmable region of interest, pixel decimation, image scaling, and lookup tables. Hubs connected to ports allow acquisition from additional cameras.