Filter Results By:
Products
Applications
Manufacturers
-
product
Non Destructive Testing (NDT)
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
product
Material Thickness
The Elcometer range of ultrasonic material thickness gauges has been designed specifically to be easy to use, calibrate, take readings and create inspection reports. With a wide range of measurement modes including: Pulsed Echo (PE), Echo Echo ThruPaint™ (EE) and Velocity Mode (VM), and a wide range of intelligent dual element transducers, the new ultrasonic non destructive thickness gauges can measure the material thickness of virtually any material such as metals, plastics, glass, epoxies and ceramics.
-
product
Non- Destructive Testing
NDT
Non-destructive testing (NDT) is an application of industrial radiography that uses X-rays to reveal defects in manufactured products or structures. Fujifilm NDT systems share digital X-ray innovations with our Fuji Computed Radiography (FCR) imaging systems.
-
product
Rebar Locator
Profometer PM-600
Profometer PM-600 is an advanced cover meter for the precise and non destructive measurement of concrete cover and rebar diameters and the detection of rebar locations using the eddy current principle with pulse induction as the measuring method.
-
product
Paper Moisture Meters
A paper moisture meter measures the humidity of paper and paper products. Use of a paper moisture meter can prevent costly damages resulting from paper expansion or shrinking. A paper moisture meter determines paper moisture content based on either absolute humidity or relative humidity. Absolute humidity does not take into consideration temperature, while relative humidity relies on temperature and is expressed as a percentage of the total amount of moisture possible at the current temperature. Thus, many paper moisture meter devices feature automatic temperature compensation (ATC).For paper producers, paper manufacturers, paper mills and others in the pulp and paper industry, moisture and humidity control is essential, especially during the production process, as excessive moisture can lead to warming of the paper rolls. A paper moisture meter can be used to detect moisture streaks during the paper production process as well as to identify optimal drying times.Regardless of whether paper is stored in paper rolls in paper converting plants or stacked in sheets and paper bales in commercial printing warehouses, the porous surface of paper gradually takes in moisture relative to the humidity of the surrounding environment. This moisture can be problematic, as too much moisture can cause curling, buckling or the formation of waves in otherwise flat paper products. Moisture also can prevent inks, dyes, paints and coatings from covering and saturating paper properly during printing and processing.PCE Instruments (PCE) offers digital handheld moisture meter devices for measuring the moisture content of paper and paper products such as cardboard, paperboard, corrugated boxes, craft paper, wrapping paper, brown packaging paper, butcher paper, recycled paper, coated paper and more. Different paper moisture meter models utilize different paper moisture measuring techniques, performing moisture content tests of paper products via either destructive or nondestructive methods. Typically, a standard pinless paper moisture meter is nonpenetrating, thus allowing for the nondestructive measurement of paper water content.
-
product
Shock Tester
DP-1200
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
product
Destructive Physical Analysis (DPA)
Is the process of disassembling, testing, and inspecting a component for the purpose of determining conformance with applicable design and process requirements. This process of sample testing is used to ensure that a high reliability component or device is fabricated to the required standards. Destructive Physical Analysis is also used effectively to discover process defects for troublesome production lot problems.
-
product
Partial Discharge
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
product
Cameras
Miro C and N
The Phantom Miro C and N series cameras are designed to fit into spaces that a standard camera can't reach. Lightweight bodies, on-board data protection, and rugged construction make them popular in automotive, microscopy, and destructive testing environments.
-
product
Humidity and Temperature
Humidity and Temperature Data Logger DL-200
Non destructive testing / Humidity and Temperature
-
product
Weld Testing
Supports industries such as Aerospace, Nuclear, Automotive, Commercial Fabrication etc.Welding procedure consultancy and approvalWelder qualification test and codingWelding procedure certificationWelder performance qualificationOn site welding invigilationOffers a complete range of destructive and non-destructive testing facilities.Responsible Welding Co-ordinators available for customer supportCAA Weld Specimen SignatoriesCSWIP Approved Inspectors
-
product
Digital Force Gauges
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
product
Motorized Test Stands
Imada offers basic and advanced motorized test stands that are available in Standard, High, and Low speeds.Use ZTS or ZTA force gauges with MX, MX2 or EMX Series test stands to enable force control and non destructive testing.
-
product
Contact Resistance Meter
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
product
Porosity Measurement Tool for the Pharmaceutical Industry
TeraSolve
This module is an addition to the TeraPulse LX product-range. It has been optimized for non- destructive determination of the disintegration and dissolution performance of finished pharmaceutical tablets and other solid dosage forms.
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
product
Wafer ESD Tester lineup
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
product
Component Test and Analysis Laboratories
The Component Test and Analysis team specializes in electronic and mechanical components such as hybrids, connectors, cables, harnesses, passive or discrete components, and digital or linear devices. The test lab has extensive experience in developing test software to electrically and environmentally characterize virtually any integrated circuit, including analog, digital, mixed signal, converters, FPGA and ASICs, as well as experience in developing actual radiation environments for parts testing. The component analysis team offers the analytical expertise and advanced instrumentation to identify root cause explanation for a wide range of component-level failures, as well as the resources to evaluate for possible quality and reliability issues through non-destructive and destructive techniques. With access to a detailed database, the Component Test and Analysis team offers a 25-year history of test and analysis data — a valuable resource for addressing new customer requirements.
-
product
Moisture Meter Pro
FLIR MR60
The FLIR MR60 Moisture Meter Pro is an easy-to-use pin and pinless moisture meter with advanced functionality. An integrated pinless sensor and an external pin probe provide the flexibility to take destructive or non-destructive measurements. Select one of the eleven material groups for pin moisture, or set a reference point for pinless moisture scanning. Then conveniently save screenshots of your measurements as a CSV file with the date, time, and settings.
-
product
Reach-In Xenon Lamp Weathering Test Chamber
Weiber xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various manufactured products towards these destructive conditions. This chamber is used for quality control, product development and scientific researches and many more. With a variety of models and options, you can customize your chamber to fit your testing needs. Reach in chambers provide a compact testing area for small applications. These are easy to install, transport and occupies less space.
-
product
4 Channel 1.0 ~ 17.0 Gb/s Pulse Pattern Generator and Error Detector
CA9806
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
product
Concrete Imaging with Ground Penetrating Radar GPR
Conquest 100
Conquest GPR: Get rapid, reliable results and reduce the need for destructive testing. Conquest GPR is a light, portable device that provides a fast, non-invasive method to gain accurate insights of objects below the concretesurface, even on a curved surface or column. Conquest GPR reduces risk by detecting rebar, post-tension cables, metallic and non-metallic conduits as well as current-carrying wires embedded in concrete. Once your concrete scan is complete, Conquest GPR connects to your mobile device, allowing you to email information directly from the field. Back in the office view your data and make client-ready reports in minutes.
-
product
Ion & Electron Detection
Photonis is the global leader in the development and manufacturing of detectors and optical components to detect ions and electrons. These detectors and components have been designed for a wide range of scientific instruments used in space and research projects but also in cells and material analysis in lifescience or non destructive testing.
-
product
Seismometers
SI value, the so called “velocity response spectrum”, is one of the standards to express an earthquake''s destructive power against structures. SW-74SI is an advanced model equipped with alarm output to 10-step and SI value output.
-
product
Walk-In Xenon Lamp Weathering Test Chamber
Xenon is one of the noble gases and is a major component of arc lamps and flash lamp and it also has its importance in general anesthetics. One of the major applications of xenon lamp is that it can be used in research applications to simulate the sunlight.Weiber walk in xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various manufactured products towards these destructive conditions. This chamber is used for quality control, product development and scientific researches and many more. With a variety of models and options, you can customize your chamber to fit your testing needs. With walk in option you have a facility to test your product in bulk quantity and even for the products which are larger in size. This chamber also known as Uv Test Chamber and Xenon Lamp Weather Resistance Test Chamber.
-
product
Industrial X-Ray
Teledyne DALSA offers powerful, innovative CCD and CMOS X-Ray detectors combining industry-leading performance with cutting-edge features for industrial and scientific applications such as NDT (non destructive testing) in evaluation, troubleshooting, research, and quality control.
-
product
Digital Force Gauge
Guangzhou Amittari Instruments Co.Ltd
The digital force gauge is a kind of simple and convenient multi-functional instrument for high-accuracy push force and pull force test. It is widely used in electronics, building hardware, textile, auto parts, ignition device such as lighter, fire fighting equipment, pen manufacturing, lock manufacturing, fishing gear, chemical, power machinery, scientific research institutions and other industries. For the push and pull load test, plug and unplug force test and destructive test etc.
-
product
Rebound Hammer
DigiSchmidt - LD
The Schmidt Hammer Digi-Schmidt Type LD was developed for the non destructive measurement of the concrete compressive strength and controlling the uniform concrete quality. Besides showing the basic settings on the included display unit, the Schmidt Hammer offers the transmission of the measured data to a standard printer or to a PC. This supersedes the time consuming business of note taking allowing the user to focus on the essential. The window based software ProVista allows downloading, presenting and editing of the measured values in a fast and easy way.
-
product
Short Circuit Test System
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
product
Destructive Physical Analysis & Failure Analysis
DPACI's component analysis laboratory performs major analytical functions, such as destructive physical analysis, failure analysis, counterfeit analysis, and material analysis on components & devices. Our destructive physical analysis techniques are performed in accordance with standards and methods used in most military and space program requirements. Solutions for difficult production problems are resolved through our failure analysis procedures.
