Filter Results By:
Products
Applications
Manufacturers
Contact Resistance
opposition to the flow of heat or electricity within a connection.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110128
Primary mating contact 610110129. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.41
-
product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
Auto Contact Resistance Tester
KVHL
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
UNI-T Series
Weshine Electric Manufacturing Co., Ltd
mainly used to measure the wire resistance of cables, the contact resistance ofswitches, connectors, relays, the resistance of coils, motors, transformer windings, and equipment enclosures, lightning protection belts, ground beams, structures, cabinets, steel bars, Test the connection resistance between metal components of water pipes, windows, guardrails, radiators, assembly lines, etc. It is widely used in telecommunications, electric power, meteorology, computer rooms, oil fields, power distribution lines, tower transmission lines, gas stations, factory grounding grids, lightning rods, etc.
-
product
Contacts Resistance Tester
JYK II
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
product
PXI 6U PXI High Density Matrix, 132x8 1-Pole
45-541-001
This 6U PXI Reed Relay Matrix Module is an ultra high-density reed relay matrix available in 132x8 format with 1- pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. The matrix is constructed using high reliability Sputtered Ruthenium Reed Relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
Micro-Ohmmeter
MR 300 C-A
The MR300C-A micro-ohmmeter enables you to perform highly accurate resistance measurements at objects with an extremely low resistance such as cables, contacts, fuses, power connections, graphite, carbon and metal samples. In the lowest measuring range of 100 µΩ the resolution is 10 nΩ.
-
product
Production Parametric Probe Card
VC20TM Fab
*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear
-
product
Circuit Breaker Analyzer
CBA 1000
CBA 1000 circuit breaker timing test equipment is a reliable and very accurate operating device for the maintenance and commissioning of circuit breakers in medium and high voltage substation. It can perform static and dynamic contact resistance measurement and it’s an accurate timing speed and motion analyzer.
-
product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG
610110129
Primary mating contact 610110128. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Capacitors - Beam Lead
Macom Technology Solutions Holdings Inc.
MACOM’s MMI-9000 and 9100 Series Chip Capacitors feature high stand-off voltage and low dielectric loss leveraging nitride/oxide dielectric layers. Gold bonding surfaces, top and bottom provide ease of bonding and minimum contact resistance. MACOMs beam lead capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which are features that produce devices with excellent long-term stability.
-
product
LXI Low Thermal EMF Matrix 1-pole 28x33
60-510-003
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178
610104142
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 30µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Solder SleeveInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 2 GHzVSWR ≤ 1.2 @ 2 GhzInsertion Loss ≤ 0.05 dB @ 500 Mhz≥ -0.3 dB @ 2 GhzDWV 1500 VDC Min.Contact Resistance ≤ 5 mΩCable Specifications RG316 & RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Circuit Breaker Testing Equipment
HISAC Swift
HISAC Swift - Circuit Breaker Operational Analyser is meant for checking the performance of the MV Circuit Breakers. The Analyser contains various intelligent measuring modules designed for measuring parameters such as contact timings of Main/PIR & Auxiliary contacts, Close/Trip Coil Current characteristics and Static Contact Resistance of R, Y & B poles simultaneously. The results can be directly viewed on the TFT touch screen display in graphical as well as numerical form. It is possible to print the graph on a built-in thermal printer or download record to PC for further analysis on CPLOT software. This all in one instrument is best suited for gang operated CBs.
-
product
Mini Coax, Contact, Receiver, Right Angle for PCB Mounting
610104160
For use with VPC Module 510104319.Primary mating contact 610103136. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination PCB TH SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR 1.445 @ 1 GHzInsertion Loss -0.885 db @ 1 GHzDWV 1500 VDC min.Contact Resistance 5mΩ max.Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
product
Signal, Contact, ITA, TriPaddle,7 Amp, 20-24 AWG
610110108
Primary mating contact 610110101. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. with Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Single Slot 3 U PXI Reed Relay Matrix Module
40-540-021
The highest density single slot PXI reed relay matrix module on the market today. This range also includes a 33x16 and 66x8 reed relay matrices with 1-pole switching. They are constructed using high reliability sputtered ruthenium reed relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance. Typical applications include signal routing in Functional ATE and data acquisition systems.
-
product
High Power, Contact, ITA, 150 Amps, 2 AWG
610150101
Primary mating contact 610149101. (May mate with other Receiver contacts, as well.)Specifications Operating Current 150 Amp Continuous using 2 AWG wireContact Resistance 0.35 mOhmsOperating Voltage 600VDC or Peak ACContact Body Cu alloyIP Tip - ThermoplasticContact Plating 30µ" Au over 100µ" NiOperating Temperature -40°C to +125°CT-Rise +40°C at 150 Amps+30°C at 125 AmpsContact Termination CrimpCycle Life 10,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.39
-
product
CB Operational Analyzer with DCRM
AutoScan PA9600
AutoScan PA9600 is a NextGen operational analyser that performs contact travel, contact timing, coil and motor current, and static and dynamic contact resistance measurements in live switchyard conditions.
-
product
Miniature Concentric Ring Set
PRF-912B
- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included
-
product
Chroma Milliohm Meters
Chroma Systems Solutions, Inc.
The Chroma 16502 Milliohm Meter is Chroma’s newest digital Milliohm Meter. 0.001mΩ~1.9999MΩ wide measurement range. DC, Pulsed, and Dry-circuit test current driving modes, enable the Chroma 16502 can be properly used in DC resistance measurement for various inductive components (coil, choke, and transformer winding etc.), cable, metallic contact (connector, relay switch etc.) and conduction materials.
-
product
Digital Low Resistance Tester
TH2512
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
product
Single 16x4 1-Pole High-Density PXI Matrix Module
40-520-403
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Kelvin Probe Set
11059A
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
product
Circuit Breaker Analyzers & Timers
CAT Handheld Series
When it’s not practical to use conventional robust circuit breaker analyzers, a handheld circuit breaker analyzer and timer may come handy. DV Power has developed a unique CAT Handheld series. It is specially designed for testing of circuit breakers with one break per phase. Their compact and ergonomic design can provide a wide range of features and reliable operations in low, medium and high-voltage substations or in industrial environments.CAT Handheld series consists of two models, CAT-P and CAT-H. Both of them have a large (5,7 in) colored touch screen display. Because of that, test results are visible in dark places as well as in bright sunlight.Powerful internal Li-Ion battery of the instruments can last up to 8 hours of testing without recharging.CAT Handheld series records:main contacts operating times,contact synchronization,sequence time,a resistance of pre-insertion resistors,open and close coil currents,main contacts bounce time,auxiliary contact time,DC Voltage.Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by triggering signal from current clamps connected to circuit breaker coil.CAT-H is capable of performing a coil control, while this feature is optional at CAT-P instrument. In contrast to CAT-H, CAT-P instrument can execute “First Trip” test.Both instruments display numerical and graphical results. Because of that, a user can easily overlay up to 4 records in the graphical form and make a quick on-site analysis of potential defects.A user can download test results to a PC via Bluetooth interface for more detailed analysis using DV Win software.
-
product
Connectors
Panasonic Automotive & Industrial Systems Europe GmbH
: They have to be as compact as possible and provide maximum reliability. To fulfil these requirements, Panasonic engineers have developed narrow-pitch connectors that utilize TOUGH CONTACT technology.In addition to their excellent shock and vibration resistance, these connectors feature an ultra slim profile, which makes them ideally suited for applications where space is valuable. Our versatile in-device connector product range offers the appropriate solution for practically any scenario.
-
product
Fine Pitch Test Probes
Micro probes allow very fine pitch testing ranging from 0.13mm to 0.35mm pitchLow Resistance, Low inductance, High FrequencyWide selection of plating options to optimize contact challenges and maximize probe lifeTri-temp applications – 55°C to 155°C
-
product
PXI Ultra High Density 64x4 2-Pole Matrix
40-533B-022
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
