Filter Results By:
Products
Applications
Manufacturers
Conducted Immunity
EUT's resilience to an injected disturbance through associated cable.
See Also: Immunity Test, Coupling Decoupling Network
-
product
Conducted Immunity Test System
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
product
EMC Testing Knowledge & Equipment
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
EMC Testing Services
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
product
Immunity
ESD coupling
is used for conducted coupling of Langer ESD pulses (200ps rise time) into ICs.
-
product
Immunity
EFT coupling
s used for direct-contact measurements of impulse immunity in IC pins, according to IEC 62215-3 and IEC 61000-4-4.
-
product
Immunity
RF coupling
is used for the conducted measurement of the immunity according to IEC 62132-4.
-
product
Ultra-Compact Immunity Tester
AXOS5
The AXOS5 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS5 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.
-
-
product
Conductivity Sensor
Conductivity sensors from Aanderaa are compact, fully integrated sensors for measuring the electrical conductivity of seawater. Conductivity is a key parameter for in-situ measurements of several fundamental physical properties of seawater.
-
product
Conductivity Type Tester
HS-HCTT
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
product
Ancillaries.. Conducted
The ease and effectiveness of conducted emission measurements can be enhanced by the use of appropriate filters. In particular, broadband noise below the frequencies of interest can cause limiting (compression) in spectrum analysers, distorting the measurements.
-
product
Electromagnetic Immunity Scanner
SmartScan BASIC
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
product
Conductivity Water Pocket Meter
LAQUAtwin EC-11
The only pocket meter that directly measures conductivity in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Portable Thermal Conductivity Analyzer
CI2100-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI2100-RQD portable thermal conductivity analyzer adopts imported high performance intelligent thermal conductivity sensor as measuring unit, which is based on microprocessor. It can test H2 concentration correctly in N2 and H2 mixed gases in a short time. - See more at: http://en.ci-ele.com/dcb675d2-4e33-4eb9-33a0-60edf78c9348/efb4c1eb-f4f5-70af-3ddd-ba6c1066c3fa.shtml#sthash.lXHNyKR1.dpuf
-
product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
product
Transient Immunity Tester
KES7700
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
product
PRO Conductivity (EC) Controller
MC311
The Milwaukee MC311 PRO Conductivity (EC) controller lets you measure and adjust EC levels automatically.
-
product
Conductivity / TDS / Salinity
The amount of mineral and salt impurities in the water is called total dissolved solids (TDS). TDS shows how many units of impurities there are for one million units of water. One way to measure impurities in water is to measure the electric conductivity of water. Absolutely pure water is a poor conductor of electricity. Water shows significant conductivity when dissolved salts are present. Over most ranges, the amount of conductivity is directly proportional to the amount of salts dissolved in the water or Salinity.
-
product
Conductivity Sensors
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
product
Conductivity Switches
B/W Controls offers a simple conductivity holder and electrode that can be configured for multiple measurement points.
-
product
Portable Conductivity Meters
Labodam portable conductivity meters are adapted with different modes for measuring quality of water on parameters such as conductivity, TDS, and temperature. Due to their portable design, they are suitable for outdoor measurements i.e. on site water testing, remote area water testing, and for research purposes. They are reliable and user friendly.
-
product
Thermal Conductivity & Diffusivity Meters
Thermal conductivity, thermal diffusivity and specific heat capacity define a material’s ability to store and transfer heat. The precise and accurate measurement of these properties is critical for any process or material, which experiences a large or fast temperature gradient, or for which the tolerance for temperature change is exacting.
-
product
Benchtop Conductivity Meter
LAQUA EC1500
Ideal for routine applications and student training.Good value for money: no fancy bells and whistles which sounds good but are rarely used.
-
product
Digital Conductivity Pen (EC)
CD611
The Milwaukee Conductivity Pen is designed for hydroponic and other growers to help you make sure that your plants are receiving the right amount of nutrient. Keep EC in your target range to help your achieve better results.
-
product
Conductivity Logger Sensor
NUL-215
This logger sensor is based on a probe with two electrodes with known surface area and distance between them. A signal is supplied to the electrodes and by testing the signal behavior, the conductivity of the solution is calculated
-
product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
Handheld instrument for electrical conductivity measurement of non-ferromagnetic metals. The electrical conductivity can be used for determining material properties, like hardness, strength, heat damage and material fatigue of metals. Rapid and simple on-the-spot conductivity measurement of non-ferromagnetic metals acc. to DIN EN 2004-1 and ASTM E 1004.
-
product
Low Range Waterproof Conductivity Pen
C65
The Milwaukee C65 Conductivity Pen is designed for aquariums, aquaculture, agriculture and pools to help you make sure that your fish or plants are receiving the right amount of nutrient to help keep your water clean and clear. Keep EC in your target range to help your achieve better results.
-
product
Battery Conductance Tester
BCT 1
Battery bank installations are important & essential part of various power, communication, information technology & industrial set-ups. In order to ensure healthy performance of such installations, the batteries used need to be properly monitored. One of the quick check methods is to measure the battery voltage & conductance of individual cells of a battery string and to identify & eliminate weak battery cells and save battery string from further degradation.
-
product
Thermal Conductivity Analyzer
Model 2000B
Teledyne Analytical Instruments
The Series 2000 represents a complete line of Thermal Conductivity Detector (TCD) based analyzers which can be applied in a wide range of applications and industries. By using field proven filament-based and semiconductor based TC detectors, Teledyne is able to continuously monitor hydrogen and a variety of other gases of interest in either binary or multi-component sample gas streams.
