Filter Results By:
Products
Applications
Manufacturers
CAT 7
telecommunication premises cabling standard operating at 600 MHz. AKA: Category 7
-
product
7/16 DIN Connectors
Pasternack 7-16 DIN connector category includes many part numbers, most are RoHS and REACH compliant. 7-16 DIN connector series in this category will terminate to coax or terminal. Our 7-16 DIN connectors are built to precise industry specifications. 7/16 DIN connector items are available in male or female gender with 50 Ohm impedance. 7-16 DIN connectors are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These DIN 7-16 connector designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 7/16 DIN connector series is in-stock. Not only are the 7 / 16 connectors in stock, but they will also ship the same day as they are purchased.
-
product
LAN Tester RJ45
CZ20250
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
product
Circuit Breaker Analyzers & Timers
CAT Standard Series
Circuit breakers are being tested during manufacturing, commissioning or maintenance stages. The most basic test requires timing measurement using circuit breaker timer. Their primary role is timing and motion measurement of medium and high voltage circuit breakers. Devices from CAT Standard series have suitable application in:electric power generation,distribution system,part of the electric power transmission system,contractors testing,and industrial environments.CAT Standard series meets the requirements of an easy to use circuit breaker timer and analyzer with an attractive price. Furthermore, they are portable and lightweight (weighs only up to 7 kg). Finally, the plastic case is unbreakable and has IP67 protective rating when the lid is closed.CAT Standard series includes five models:Three circuit breaker timers – CAT03, CAT31, and CAT61Two circuit breaker analyzers – CAT34 and CAT64CAT03 is a basic model intended only for timing measurement of main contact operations on the circuit breaker with one break per phase. Unlike CAT03, CAT31 has the possibility of circuit breaker operation initiation, coil current measurement, and auxiliary contact timing measurement. CAT61 differs in comparison to CAT31 by its ability to measure up to two breaks per phase.CAT34 and CAT64 are more advanced compared to CAT31 and CAT61, respectively, since they have additional analog channels. Also, they have the possibility of a travel curve recording.A user can download the test results to a USB memory stick or save it to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Optional thermal printer prints test results in tabular and graphical form on 80 mm (3.15 inch) paper rolls. CAT Standard series instruments are compatible with DV-Win software. It provides full control of all CAT functions from a PC, as well as acquisition and analysis of test results.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
7 Tesla Optical Cryostat
OptiCool®
The OptiCool by Quantum Design is a new optical cryostat using an innovative design that puts the sample volume in the heart of your optical environment. A custom 3.8 inch bore, split-coil, conical magnet offers fields perpendicular to the optical table up to ±7 tesla. The highly integrated design means, even with a magnet, your sample isn’t buried inside a large cryostat, far away from the optics. Seven side optical ports and one top optical port allow for optical access to your sample from a wide array of directions.
-
product
COM Express Type 7
One of the most fundamental innovations of the COM Express Type 7 pinout is the support of up to four 10GbE interfaces, essential for the next generation of edge node appliances. Type 7 modules are headless (no graphics), which is why they are also referred to as “Server Level COM Express”.
-
product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
product
Laser Head Cable, 7 m
10881B
Provide reliable power with this five-pin female DIN that connects the laser head to multiple laser boards.
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-51NAV
This versatile clamp-on power meter offers a full range of diagnostics, including those that HVAC technicians need most—volts, amps, resistance, capacitance, DC microamps, in-rush current and temperature.
-
product
COM Express Type 7
ROM-8720
Advantech ROM-8720 COM Express Type 7 Compact Computer-on-Module is powered by NXP LS1046A SoC which includes four Arm Cortex-A72 cores for Edge networking and Edge firewall, two 10Gbsp-KR and up to four Gbps for the networking communications. Three PCIe, three USB 3.2 Gen1 and three USB2.0 for the embedded interface expansions. two UART, one SPI and 8 GPIO for embedded device controls.
-
product
Atec Series 7
TEC® Series generic purpose test benches are used by most airlines, systems manufacturers and MROs (Maintenance, Repair and Overhaul) companies to guarantee the conformity of critical electronic equipment. Available on all continents, the ATEC® Series can be adapted to suit various needs owing to its modular nature and capacity to test almost all airliner LRUs. SPHEREA has the world’s largest testing library.
-
product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-50NAV
ACD-50NAV clamp-on power meter offers AC current measurements to 600 A, AC/DC voltage to 1000 V, and wide jaws to accommodate large conductors. This clamp-on multimeter is ideal for industrial power monitoring and verifying system conditions.
-
product
Soft Carrying Case, 4-5/7 In. D, Black
U1175A
Soft carrying case for U1200 series clamp meters; 4-5/7 in, black
-
product
LTE US Version - 4G, Cat.1, GNSS Tracker
Wio LTE
Wio Tracker (Wireless Input Output) is an open source gateway which enable faster IoT GPS solutions. It is Arduino and Grove compatible development boards that helps you track nearly any moving thing on the planet and then upload that data wirelessly. The Wio LTE is the LTE version of Wio Tracker, so now we’ve got 2 versions of Wio Tracker and the LTE (4G) version will make some differences.
-
product
PXI 8-Slot BRIC Matrix, 154x8 1-Pole (7 sub-cards)
40-562B-121-154X8
The 40-562B-121-154X8 is a high density BRIC8 matrix module with a size of 154x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Multiplexer, 40-Channel, 20-Pole (7 Sub-cards)
40-570A-315
The 40-570A-315 is a 40-channel, 20-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
VPX Chassis 4U/50HP 7 Slots
BKP3-CEN07-15.2.3-4
his 7 slot Hartmann Open VPX BKP3-CEN07-15.2.3-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 50HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with a 600W plug-in power supply and a 1U removable, bottom mount fan tray.
-
product
PXI 8 Slot BRIC 154x8 1-Pole (7 sub-cards)
40-562A-121-154X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 8 Slot BRIC 322x8 1-Pole (7 sub-cards)
40-560A-121-322X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Virtex 7 FPGA Carrier
PC7: 330/690
The PC7 family of FPGA carrier boards is DEG’s latest AMD-based product innovation. With the ability to host two FMCs (FPGA Mezzanine Cards) with rear panel I/O, the PC7 product line sets the benchmark for performance and versatility in the embedded PCIe market. Coupling this flexibility with a AMD Virtex-7 VX330T or VX690T FPGA, the PC7 enables multi-channel high-speed data acquisition and extensive digital signal processing all within a single PCIe slot.
-
product
7½-Digit Graphical Sampling Multimeter
DMM7510
The DMM7510 combines a precision, high-resolution digital multimeter (DMM), graphical touchscreen display, and high-speed, high-resolution digitizer to create the first graphical sampling multimeter. With pA-level sensitivity and 1Msample/s sampling, it accurately measures ultra-low sleep mode currents and transmit drain currents from wireless devices.
-
product
PXI 12-Slot BRIC Matrix, 308x4 2-Pole (7 sub-cards)
40-562B-322-308X4
The 40-562B-322-308X4 is a high density BRIC12 matrix module with a size of 308x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PXI 8 Slot BRIC 644x4 1-Pole (7 sub-cards)
40-560A-121-644X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 8 Slot BRIC 210x8 1-Pole (7 sub-cards)
40-561A-121-210X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 8-Slot BRIC Matrix, 154x8 2-Pole (7 sub-cards)
40-562B-122-154X8
The 40-562B-122-154X8 is a high density BRIC8 matrix module with a size of 154x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
8-Slot BRIC, 294x12, 1 Pole, PXI Matrix (7 Sub-cards)
40-559-801-294x12
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
COM Express Type 7 10GBASE-T Network Adapter Card
10GBASE-T Network Adapter Card
- Supports up to four 10GbE copper interface (10GBASE-T)- Compatible with PICMG COM.0 R3.0 Type 7 modules
