Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Circuit Protection - Breakers
Eaton’s complete line up of low and medium voltage circuit breakers and fuses are used to provide circuit protection in alternative energy, commercial, industrial, mining, and military applications, where they protect against overloads and short circuits in conductors. These circuit breakers are applied in panelboards, switchboards, motor control centers, control panels, combination starters, individual enclosures, and bus duct plug-in units.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Voltage Detectors & Others
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
-
product
Breaker Testing Software
BTS11
To test circuit breakers in general, is to operate the breaker and check the contact timing. However in factory testing and during field service/maintenance some other tests are necessary. For field testing these other tests can also be very useful in diagnostics purpose.
-
product
Adjustable Test Stab Set
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
product
Automatic Circuit Breaker Test Systems
UPA-1 (UPA-3)
These portable systems for primary injection testing of circuit breakers which are used in in AC circuits of industrial frequency.
-
product
Circuit Breaker Simulation Device
PSS01
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
product
Circuit Breaker SiMUlator
VAWDS-2
Circuit Breaker Simulator WDS-2 is used to simulate the circuit breaker operation to check the relay scheme performance.Place two sets of independent circuit breaker simulator in one caseAble to simulate three-phase or single-phase operation of circuit breakerAble to simulate single trip coil or double trip coil circuit breakerHas simulated closing/opening coil input terminal.
-
product
Measuring Display Unit Breakers
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
product
Digital Earth Resistance Tester
8PK-ST1520
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
product
3 Wire (Digital) Earth Resistance Tester
4120 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
product
3 Phase Relay Test Set
This is a portable Relay Testing Set suitable for testing different types like over current, earth leakage relays, circuit breakers of 1A – 50A rating etc. All the components are assembled and enclosed with a portable air cooled M.S.cabinet.
-
product
Portable Relay Tester
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuit and will possibly prevent serious damage to plant or injury to personnel. Apart from checking the protective circuits correctly, it is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay tester.
-
product
Digital Circuit Breaker Analyzer
CT-7000 S3
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
product
Transfer Switches
Q Series
The Pro/Tran Q Series features 1-inch interchangeable circuit breakers. A 30A double-pole circuit breaker and a 20A double-pole circuit breaker, to handle heavier loads on the generator side, are included on each model. The balance of the circuit breakers are single-pole 15A.
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
SF6 Leakage Detector
GDWG-IV
GDWG-IV SF6 Gas Leak Detector is infrared type leak detector. It is color LCD display and real-time shows SF6 concentration. It rapidly detect SF6 breaker, GIS leakage point and yearly leakage rate qualitatively and quantitatively. It's a good device suitable for power supply department, installation and overhaul unit, power test institute.
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT M3K+
SCOT M3K+ measures and displays CLOSE, OPEN and CLOSE-OPEN times of Main contacts of 3 poles connected end to end, simultaneously. Ideally suitable for CBs with single break per pole.
-
product
Contact Resistance Meter
CRM 200B
CRM 200B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions.CRM 200B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.
-
product
300kV/5mA DC Hipot Tester
HDZG
HD Power Test Equipment Co.ltd
HDZG-305 300kV/5mA DC high voltage tester is used for testing DC high voltage for zinc oxide arresters,magnetic blowing arresters, power cables,generators,transformers,circuit breakers and other equipments,which is suitable for electric power branch,power department of factories,scientific research units,railway,chemical industry,and power plants.
-
product
Intelligent Circuit Protection
The Mors Smitt ‘Intelligent circuit protection system’ controls and monitors all AC and DC circuit breakers remotely and is capable of providing complete status of all MCB’s via display or through the Train Management System.
-
product
First Trip Testing of Circuit Breakers
Significance of Circuit Breaker "First Trip Time"A circuit breaker may not be called upon to operate and clear a fault for years, but when a fault occurs, it is expected to operate within it's published time-current characteristics. Unfortunately, frequently this does not happen... environmental contaminants, hardened grease, vibration and other factors can adversely affect the operating time of the circuit breaker.
-
product
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger
SD750100G
Zhejiang Sandi Electric Co., Ltd
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger is for DC battery system charging station. With three-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-500Vdc output voltage range optional, suitable for all types of batteries.FeaturesProduct Introduction：SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module.Unique function：● High efficiency over the full load range, full load efficiency greater than 95.5%● Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery● 5-inch LCD touch screen, easy to operate● Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operateMain features：● Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc.● Three phase active power factor correction technology, reduces the harmonic interference to the grid● Dual DSP design, achieve the full digital control, less components means high reliability● Wide input voltage range, allows operation in most poor grid conditions● Soft start charging and soft shutdown minimize the impact on the battery.● Input, output have protective circuit breaker switch● Module adopts hot pluggable design, which is convenient for maintenance.● CAN/RS485 interface (Optional)SpecificationModel SD750100GAC input Input system Three phases + PEVoltage range 280Vac ~500VacRated voltage 440VacFrequency range 50Hz/60HzMaximum current <74AITHD (total harmonic distortion) <5%DC output Output power 40KWVoltage range 50-750Vdc ( can set)Constant power output voltage range 400Vdc-750VdcOutput current range (A) 100A ( 1~100A can set)Output current limit 1-100A continuously adjustableSteady voltage precision <±0.5%Steady current precision ≤±1% (rated range of 20% ~ 100% for output load)Load regulation rate ≤±0.5%Startup overshoot ≤±3%Peak-to-peak value noise ≤1% (200~1000V, 0~20MHz)Display Indication Light Green LED: normal operation,Yellow LED: alarm, Red LED: failureDisplay language EnglishDisplay 5’ LCD touch screenPower factor and THD Power factor ≥0.90 Full-load output power of @20%~50%≥0.98 Full-load output power of @50%~100%≥0.99 Full-load output power, input nominal voltage and frequency of @100%THD ≤5% Full-load output power of @50%~100%Protection function input overvoltage Protection Over Under Voltage automatic shutdown and restart when voltage return normalOutput overvoltage protection Over Under Voltage automatic shutdown and restart when voltage return normalOver-temperature protection Automatic shutdown. Automatic restart when the temperature return to normalShort circuit protection Automatic shutdown and lock, need power off to restart to unlockEfficiency Under Rated input voltage ≥95.2％
-
product
Digital Earth Resistance Testers
ST-1520
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
product
Dual Range Non-Contact Voltage Tester
NCVT-2
Automatically detects and indicates low voltage (12-48V AC) and standard voltage (48-1000V AC) allowing broad application.Non-contact detection of standard voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets and wires.Non-contact detection of low voltage in security, entertainment, communications, environmental control, and irrigation systems.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.Digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator.CAT IV 1000 Volt rating provides expanded operation and protection.
-
product
Circuit Breaker Analyzers & Timers
CAT Handheld Series
When it’s not practical to use conventional robust circuit breaker analyzers, a handheld circuit breaker analyzer and timer may come handy. DV Power has developed a unique CAT Handheld series. It is specially designed for testing of circuit breakers with one break per phase. Their compact and ergonomic design can provide a wide range of features and reliable operations in low, medium and high-voltage substations or in industrial environments.CAT Handheld series consists of two models, CAT-P and CAT-H. Both of them have a large (5,7 in) colored touch screen display. Because of that, test results are visible in dark places as well as in bright sunlight.Powerful internal Li-Ion battery of the instruments can last up to 8 hours of testing without recharging.CAT Handheld series records:main contacts operating times,contact synchronization,sequence time,a resistance of pre-insertion resistors,open and close coil currents,main contacts bounce time,auxiliary contact time,DC Voltage.Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by triggering signal from current clamps connected to circuit breaker coil.CAT-H is capable of performing a coil control, while this feature is optional at CAT-P instrument. In contrast to CAT-H, CAT-P instrument can execute “First Trip” test.Both instruments display numerical and graphical results. Because of that, a user can easily overlay up to 4 records in the graphical form and make a quick on-site analysis of potential defects.A user can download test results to a PC via Bluetooth interface for more detailed analysis using DV Win software.
-
product
Bay Control
Schweitzer Engineering Laboratories, Inc.
Integrated bay control systems combine complete bay control with high-speed breaker protection, allowing you to deploy a full substation protection, control, and monitoring solution that is flexible for your application.
-
product
Micro OHM Meter
Cambridge Instruments & Engineering Co.
This Test set is capable to measure low resistance like switch contacts, breaker contacts, busbar slices, joints, fuses, low inductive windings etc.
-
product
Resistance Measurement
PROMET
High-precision micro-ohm measuring systems with adjustable DC test current for determining resistances on circuit breakers or inductive loads such as transformers, for example. The high-precision ohm meters of the PROMET series are used to determine very low electrical resistances in the µΩ range. The adjustable test current of up to 600 A in combination with a four-wire measuring method delivers measurement results which meet stringent accuracy requirements. State-of-the-art power electronics coupled with a robust design guarantee excellent reliability for use as a portable device in switching stations and industrial environments. Typical applications include determining the contact resistance of switchgear devices and determining the resistance on inductive loads such as transformers.
