Filter Results By:
Products
Applications
Manufacturers
-
product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
LXI Microwave Multiplexer, SP4T, 12-Bank, 50GHz, 50Ω, SMA-2.4
60-803-712
Our 60-803-712 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 12-Bank, 26.5GHz, 50Ω, SMA
60-803-312
Our 60-803-312 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Acute High Voltage Differential Probe, 10x/100x, 100MHz, 700V
ADP1100
*USB Powered (or Power Bank)*Bandwidth up to 10 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
ARINC 429 Card
SET-1623
The SET 1623 ARINC Card has 32 Tx/Rx Channels. These 32 Tx/Rx channels are structured in 4 banks (P0.x to P3.x) 8 channels each. Each bank is controlled by a dedicated SPI (SPI0 to SPI3) located on RTI.
-
product
High Density Versatile Multi I/O Module
AMC080/080C
The AMC080 is high density versatile I/O module. The 15 banks of 8-bit I/O can be used as input and or/output and are configurable to run as +3.3V or +5V. The unit interfaces to the system via GbE and/or PCI/10GbE. The I/O’s are accessible via HDC. It also has 8 bi-color LED’s on the front panel for indication and status. All LED’s are reconfigurable.
-
product
LXI Microwave Multiplexer, SP4T, 8-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-508
Our 60-803-508 is a 8 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF1000
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations.
-
product
Photo-Frame Style Smart Signal Detective Jammer
WF-DJ7
Shenzhen Tangreat Technology Co., LTD.
WF-DJ7 is a Painting Smart Signal Jammer.WF-DJ7 is designed mainly used for indoor cellphone signal detection and shielding, such as meeting rooms,border control units, Border Patrol and Drug Enforcement, Customs, Houses, Churches, Courts, Theaters, Offices,classrooms. checkpoint personnel, Hospitals, Recording Studios, Banks, Contract Tendering Rooms, Testing Facilities, Security Services, Military Units, Secret Services, News Conference Scene, Libraries, Museums,Prisons and so on.
-
product
Switched Filter Banks
K&L Microwave provides Switched Filter Bank (SFB) products built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on an existing design or to provide specifications for a custom design.
-
product
Interferometer
S100|HR
CNC polishing puts new demands on metrology tools. Many of these optics are aspheric with tight tolerances. The new machines can produce almost any surface and require a new level of metrology to provide feedback to the polishing process. This just cannot be done with outdated interferometers designed over 30 years ago. The S100|HR has the performance it takes, without breaking the bank. Measure 10X higher fringe densities to enable final figuring to begin sooner, saving you time and money. Plus measure these high density fringes 5X more accurately to enable large polishing corrections that converge quickly to final figure, including aspheres.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 13-Bank 6GHz SMA
60-801-013
The 60-801-013 is a 6-channel, 13-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP6T, 15-Bank, 67GHz, 50Ω, SMA-1.85
60-800-815
Our 60-800-815 is a 15 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Attenuator Banks
HYTEM offer different RF attenuation systems that allow to perfom simultaneous types of tests on multiple RF links (handover for instance). Multiple configurations are available : Standard, MIMO, Link separation, Spécific.
-
product
Load Banks
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 1-Pole
42-321-104-HI
The 40-321-104-HI (PXI) and 42-321-104-HI (PXIe) are single 9-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Cavium CN6880 Processor AMC
AMC738
The AMC738 utilizes the 32 Core Cavium Octeon II Processor that combines with a Xilinx V7 (XC7VX690T) FPGA to provide 100GbE via the CFP2 module. The CFP2 module could utilize 4 x 25 Gbps lanes or 10 x 10 Gbps lanes. The module follows the AMC.1, AMC.2 and AMC.4 specification. The FPGA has a single bank of 64-bit wide DDR3 memory.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 10-Bank 26.5GHz SMA
60-802-310
The 60-802-310 is a 4-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Low Voltage Capacitor Banks
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
product
PXI 2 Banks of 32 Chan 1 Pole MUX
40-657-001-2/32/1
40-657 High Density Power Multiplexer Modules are available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
LXI Microwave Multiplexer, SP4T, 1-Bank, 50GHz, 50Ω, SMA-2.4
60-803-601
Our 60-803-601 is a 1 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 13-Bank 6GHz SMA
60-802-013
The 60-802-013 is a 4-channel, 13-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 10-Bank, 26.5GHz, 50Ω, SMA
60-803-310
Our 60-803-310 is a 10 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI Hex SPDT RF Switch MCX 75 Ohm
40-830-106
The 40-830-106 is a 75Ω RF Switch with 6 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
LXI Microwave Multiplexer, SP4T, 13-Bank, 18GHz, 50Ω, SMA
60-803-113
Our 60-803-113 is a 13 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
42-870A-106
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
product
LXI 75Ω 6:1 Microwave Multiplexer 16-bank 2.5GHz 1.6/5.6
60-820-016
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
product
PXI Dual 12x8 Matrix, 2 Pole Switching
40-522-022
Medium density PXI dual 12x8, 2-pole matrix - it is also available in reed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
product
LXI Microwave Multiplexer, SP4T, 6-Bank, 26.5GHz, 50Ω, SMA
60-803-306
Our 60-803-306 is a 6 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
