Filter Results By:
Products
Applications
Manufacturers
-
product
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV
RP4060
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
product
Attenuator
RFATT AXIe-0
*Dual channel AXIe attenuator with frequency range from 9 kHz to 10 GHz.*The module is designed to work as part of information measuring systems as a normalizer of radio frequency signals (power control: signal amplification or attenuation).
-
product
2 Channel Variable Optical Attenuator
S-105
VOA slot module of FOTS system is a module that installs a built-in dual channel MEMS type VOA inside and can do two separate attenuation functions with two each VOA channel being driven individually. This module controls the optical power precisely to maintain the desired output level set by the user by automatically correcting for power drift or fluctuation.This slot module provides high-performance power control features such as high attenuation range, accurate tolerance, stable spectral flatness and low insertion loss in the wavelength range of 1260 ~ 1600 nm. It also offers a particularity that the high-speed drive of attenuation is possible through the combination of high-speed FPGA processor and high speed response time (within 1 ms) VOA. With the provided driving program and GUI, users can set up various attenuation program of each VOA channel such as sequential attenuation step, periodic attenuation and operation time
-
product
SP500X , 500 MHz, ±300 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
783629-01
The SP500X, or Multi-Contact Isoprobe IV - 10:1, is a standard passive probe with fixed 10x attenuation for oscilloscopes that provide 1 MΩ input impedance.
-
product
÷10, 500 MHz, 10 MΩ, Passive Probe (Total of 1 Per Channel)
PP008-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
EDFA
SPA-2-4X22-WDM EYDFA
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Coaxial Fixed Attenuator, DC to 26.5 GHz
8493C
The Keysight 8493C coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator has APC-3.5 connectors and is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 40 dB.This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
product
MS-M 3-Pin RF Cable Assembly, Female to Unterminated, 0.5m, RG178 Cable
40-979A-503-0.5m-FU
This 0.5m long MS-M RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
product
Voltage Controlled Variable Attenuators
A voltage variable attenuator is an electronic device that provides a variable attenuation depending on the voltage applied
-
product
93 Ohm Coax Cable
RG62A/U
RG62A/U part number from Pasternack is a RG62 coax cable that is flexible. Pasternack RG62 flexible coax cable is 93 Ohm and has a PE (AS) dielectric. Our RG62 coax is constructed with a 0.239 jacket made of PVC. RG62 coax has a shield count of 1, a RF shielding of 45 dB and the maximum frequency for this Pasternack cable is 1 GHz. RG62 coax cable has an attenuation at 1 GHz of 8.7 dB and a maximum power of 77 watts at 1 GHz.
-
product
Passive Probe, 10:1, 75 MHz, 2-Pack
N2142A
The Keysight N2142A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 75 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
product
Multi-angle Polarized Light Scattering Measurements
LISST-VSF
In-situ measurements of P 11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.
-
product
Digital Step Attenuators (DSA)
High linearity, fast switching time with broad bandwidth. Best-in-class attenuation error with fine attenuation steps. Most robust ESD protection available.
-
product
Injection Transformer
J2100A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
Digital Attenuator Operating Frequency of 1 to 20 GHz
LDA Series
The LDA series of Lab Brick® RF and Microwave Programmable Digital Attenuators includes 50 Ohm and 75 Ohm bidirectional RF step attenuators with calibrated operation up to 20 GHz. These USB powered and controlled units require no additional DC supply voltage. They are easily programmable for fixed attenuation or swept attenuation ramps directly from the included GUI. Lab Brick Digital Attenuator API DLL, Linux drivers and LabVIEW-compatible drivers are also available for custom programming applications.
-
product
High Impedance Active Probes
12C
A high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.
-
product
Coaxial Fixed Attenuator, DC to 18 GHz
8493B
The Keysight 8493B coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Attenuators
Teledyne RF & Microwave offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, RF&M has a product that meets your demanding needs.
-
product
Touch Screen Mini OTDR, 1310/1550nm
TR1200 Series
Shenzhen Sharingtek Communication Co., LTD
1. 4.3-inch multi-touch capacitive screen support zoom function screenshot2. Intelligent multi-function 12-in-one functional module: automatic OTDR expert OTDR event map optical power meter visible fault locator adjustable light source optical loss test RJ45 sequence test RJ45 length test RJ45 digital tracker flashlight end face detection (optional)3. Automatic OTDR no complicated settings one-key test4. Expert OTDR professional measurement mode simultaneous display of curve list and MAP view5. Event blind zone 2.5m attenuation blind zone 8m measuring range up to 100KM6. Support optical test with optical signal less than -5dBM high isolation bilateral filter technology7. Support automatic saving SOR file format 8G storage capacity 200000 records can be stored8. Support Type-C charging interface 4000mAh polymer battery battery life is more than 12 hours
-
product
10:1 500 MHz 10 MOhms Passive Probe
PP005A
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MO. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Attenuation Control Unit, DC to 26.5 GHz, 0 to 101 dB, 1-dB Steps
J7201C
Designed for wireless communication and aerospace and defense applications in both R&D and manufacturing test.
-
product
Passive Probe, 10:1, 500 MHz, 1.3 M
N2873A
The N2873A passive probe offers DC to 500 MHz and 10:1 attenuation factor to address a wide range of measurement needs.
-
product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
product
Coaxial Attenuators Set
11581A
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
product
Manually Variable Attenuators
The JFW 50 Ohm dual rotary attenuator has been a staple tool to RF engineers for over 30 years. Our years of proven quality and performance make our manually variable attenuators right for any RF environment. Whether you are using the rotary attenuator on your RF test bench or mounting it to a panel, the JFW dual rotary attenuator makes adjusting attenuation quick and easy.
-
product
PMC Compatible Wizard Interface
PMC-Wizard
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
product
SA1500X, 1.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784256-01
The SA1500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
