Attenuation
-
Product
Differential Probe
DP-40K
-
*MAX. Input Voltage: ±20KV DC or 40KV p-p or AC 14KV rms*Bandwidth: DC-20MHz*Input Impedance 100MΩ// 1PF*x500, x5000 Attenuator*To Ground MAX. Voltage: 10KV CAT III*Output Impedance 50Ω
-
Product
Attenuators
-
Flann manufactures a portfolio of both manual and programmable attenuators that cover a wide range of applications and waveguide bands
-
Product
Digitally Controlled Programmable Attenuators
-
Broadband frequencies ranging from 30 MHz to 40 GHz. High attenuation levels up to 60 dB. PIN diode designs exhibit extremely fast attenuation step switching performance. Attenuation step size ranges from 0.03 dB to 1 dB. Programmable attenuator control bit sizes range from 5 to 10 bits. Models powered and command controlled via 15 pin female Micro-D socket or USB interface.
-
Product
Differential Probe
DP-02VF
-
*150MHz High Frequency*MAX. Input Voltage:*±40V DC or 80V p-p or AC 28V rms*Bandwidth: DC-150MHz*Input Impedance 1MΩ // 7.5PF*X2, X20 Attenuator*To Ground MAX. Voltage: 40V*Output Impedance 50Ω
-
Product
Probe/SMA
WPRB-8CPGS
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
Product
Variable Optical Attenuator - PXI
VOA 1000 / 1100 / 1300 Series
-
The VOA Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fiber types and various wavelengths to suit a wide range of applications.With 1 or 2 channels in a single PXIe slot, it provides high channel density solution for easy integration in the versatile PXI platform.
-
Product
Adapter/Stainless Steel
WADP-NMNM-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Attenuator Interconnect Kit, 2.4 mm
11716F
-
The 11716F attenuator interconnection kit provides the necessary parts to connect 84904/8M and 84904/6L programmable step attenuators in series.
-
Product
Attenuators
-
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
Product
Passive Devices
-
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
Voltage Variable Attenuators
-
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
Product
Flexible Cable Assembly
WCBA-WC0129M.29M1
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
-
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Attenuators
-
Optical attenuators reduce the intensity of transmitted light uniformly across the spectrum. Applications include preventing too much light from overloading a receiver.
-
Product
Attenuators
-
Reduces the amplitude of a signal without appreciably distorting its waveform.
-
Product
Dual Attenuator
V859
-
The Model V859 is a passive dual section attenuator housed in a 1-unit VME module; the module does not require any power supply since it is made up of resistive cells
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
Optical Communication Parts
-
Adamant Namiki Precision Jewel Co Ltd.
Zirconia ferrule sleeve is an important part in optical fiber communication and is the basic product of our optical communication parts. We have developed an optical communication parts part of hasad developed based on grinding and bearings. Offer Optimum Performance And Quality For Each Type Of Optical Fiber, Optical Connector And Optical Device. We Also Offer Pin Gauges And Ring Gauges For Measuring Precise Dimensions Indispensable To Our Quality Assurance . These Gauges Have Little Wear, Good Compatibility With Ferrules And Sleeves, Zirconia , sapphire and cemented carbide are used as materials.Various Optical Connectors And Adapters Using Ferrules And Sleeves, Follow The Long History FC And SC Connectors, MU , LC Connectors Are Also Available. In Particular, LC Connectors Are Deployed In A Wide Lineup With Adapters. In The Field Of Optical Devices, We Provide Codes Master , Various Patch Cords , Conversion Adapters That Connect Different Types Of Connectors, Attenuators And Terminators That Provide Stable Characteristics, Which Are Manufactured Using The Ferrule Quality Of Our Own Manufactured Parts We Will. We Also Offer Parts For Optical Devices SuchAs Fiber Array Used For Connection Of PLC, AWG And Others. In The Field Of Optical Modules, SC And LC Receptacles , Fiber Stub, Pigtail Fiber And Other Optical Module Parts, And Now We Have Provided TOSA, ROSA And Other Optical Module Manufacturing Consignment Services. We Also Deal With Various Lensed Fibers Which Processed Fiber Tip With High Precision . In Addition, We Also Flexibly Deal With Precision Component Processing Used In Optical Communication Field, Special Specification Ferrule, Sleeve Etc. Please Contact Us.
-
Product
PXI Programmable Step Attenuator Module, DC to 50 GHz
M9168E
-
The M9168E is a programmable step attenuator module based on PXI hybrid platform. The M9168E operates from DC to 50 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
SA2500X, 2.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784257-01
-
The SA2500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
-
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
Product
Voltage Controlled Variable Attenuators
-
A voltage variable attenuator is an electronic device that provides a variable attenuation depending on the voltage applied
-
Product
Fixed Attenuators
-
ZTS provides 2 to 1000 Watts fixed attenuators with many types of connectors to choose from, maximum frequency would reach 67 GHz, we also provide custom or calibrated service as per your request.
-
Product
Attenuator / Switch Driver
11713D
-
The 11713D attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
Fixed Attenuator (Coaxial)
-
RF Lambda’s fixed coaxial attenuators are used to adjust the signal level in any RF system. They are most commonly used to reduce high power signals in order to inject into test equipment or other parts of the RF system requiring lower signal levels. They are highly reliable and come in a variety of frequencies, powers, and connectors.
-
Product
One-Channel Variable Optical Attenuator
N7761A
-
The N7761A attenuator is an extension to Keysight's high density N77xx-family that establishes a new standard in space-saving fiberoptic instrumentation.
-
Product
Manual Attenuator (Coaxial)
-
Manual control coaxial attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
