Fuel Cell Test Systems
-
product
Tracer Gas Leak Test Systems
Tracer gas leak testing is a simple and highly-efficient method of leak detection that provides high sensitivity as well as increased accuracy and repeatability. This method is used for testing parts with very low leak rates that are outside the range for conventional air-flow pressure decay and mass flow, or to replace bubble test methods. Tracer gas testing uses escaping tracer gas to identify micro-leaks in the range of 1x10-4 to 10-9 scc/s.
-
product
NFC Physical Layer Test System
IQnfc+
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
DC Hysteresis Graph Test System
DX-2012H
Automatic measurement of the demagnetization curve of permanent magnetic material such as ferrite, AlNiCo, NdFeB, SmCo, etc. Accurate measurement of the magnetic characteristic parameters of remanence Br, coercive force HcB, intrinsic coercive force HcJ and maximum magnetic energy product (BH)max.
-
product
Advanced Driver Assistance Systems (ADAS) Testing
Advanced Driver Assistance Systems (ADAS) TestingAll modern vehicles are now being equipped with Advanced Driver Assistance Systems (ADAS). The development of such systems requires complex testing, including the ability to control and calculate relative positions between multiple vehicles and objects in real-time. We provide an effective solution for ADAS testing with highly accurate GPS positioning systems to measure relative positions and velocity between multiple vehicles and objects.
-
product
Electrodynamic Vibration Test Systems
CV-series
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
product
Vehicle Test Systems
What counts in development processes is the speed at which new vehicles and new technologies are made ready to go into production. For vehicle testing, this means that complex test problems must be solved. HORIBA develops vehicle test stands that simulate the realities of driving in the most varied situations both precisely and economically.
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Basic Fuel Injection Pressure Tester
FIT448
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
Electrical Protective Equipment Test Systems
СВС-50М (СВС-100М)
CBC-M-series systems are designed for high-voltage testing of electrical protective equipment and insulated hand tools. Withstand tests are carried out with AC voltage (CBC-50M: UAC ≤ 50 kVRMS; CBC-100M: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
product
Switching System Test Tools
EBIRST™
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
product
Modular Test System
The GS-X modular system is used for functional testing of medical devices and for testing the electrical safety of medical and general portable devices.
-
product
Load Cell Indicator
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
-
product
Power mixed test system
Power device or module with which are digitally controlled and memory can be measured per system.
-
product
Compact Low Profile Load Cell
1000 Series
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
product
Semiconductor & Electronic Systems Test and Diagnostics Services
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
product
Battery Test Systems
The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.
-
product
Universal Testing Systems (Up To 2000 KN)
Industrial Series (DX, HDX, KPX)
The Instron static hydraulic universal testing systems — part of the Industrial Series — are rugged, high-capacity frames built for demanding material tests in tension, compression, flexure and shear up to 2,000 kN. Featuring large-diameter columns and rugged components for superior frame stiffness and durability, these systems deliver reliable, repeatable performance for high-force testing needs in metals, composites, concrete, fasteners, and structural materials.
-
product
Pedal Force Load Cells
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
product
SOLAR CELL TESTER
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
product
Goniophotometer Test System For Led Lamp
1680A 1680B
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
product
Load Cell Simulators / Testers
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
product
vibration test system
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
product
Long-Stroke Tensile Testing System For Vulcanized Rubber
Capable of Measuring Even Specimens with a Large Break Strain A tensile test method for vulcanized rubber is stipulated in JIS K6251 (Rubber,vulcanized or thermoplastic-Determination of tensile stress-strain properties). One of the properties of vulcanized rubber is significant elongation. This long-stroke tensile testing system for vulcanized rubber has a long stroke that is required for calculating these tensile characteristics of rubber, and accommodates dumbbell specimens Nos.1 through 6 stipulated in JIS K6251.
-
product
High Energy Shock Test System
KRD13 series
KRD13 series high energy shock test system is specially designed to meet the requirements of military and automotive testing. The system adopts the principle of pneumatic energy storage expansion. By adjusting the inflation pressure, various high-level acceleration tests can be easily implemented in a short stroke.For the high-G classic shock test, it’s equipped with the corresponding shock amplifier to complete high-peak shock test.
-
product
Test Automation System for Durability Testing
STARS MATS
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
product
Controlled impedance test system
CITS900s4
CITS900s4 is the seventh generation of Impedance test system from polar, and typically the most popular model for customers who are new to impedance control. CITS900s4 provides both differential and single ended measurement capability along with 4 channels to provide flexible probe connection.
-
product
Electroluminescence Test Systems
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
product
Electronic Fuel Quantity Indicator
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
