-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Averaging Clip-on Extensometer
2650 Series
-
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
Product
High Temperature Un-Cooled Extensometers (700 C)
Model 7642
-
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the extensometer. This system provides a number of functional enhancements, including high speed digital output, built in calibration and tare functions, analog and digital filters, and more.
-
Product
Extensometers
-
Instron offers one of the industry’s most comprehensive ranges of extensometers, providing precise, reliable strain measurement for virtually any materials testing application. From clip-on and automatic contacting units to advanced video and non-contacting systems, Instron’s extensometers deliver exceptional accuracy and repeatability across static, dynamic, and high-temperature environments. Designed and manufactured in-house, these solutions support global ASTM and ISO testing standards, helping laboratories achieve consistent, traceable results across metals, composites, plastics, and elastomers.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
High Temperature, Low Strain Capacitive Extensometers (1200 C or 1600 C)
Model 3648
-
Jinan Testing Equipment IE Corporation
These extensometers use a high temperature capacitive sensor in combination with an innovative design to achieve high accuracy strain measurements in low measuring ranges not possible with other high temperature extensometers. They mount on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The overall design reduces any influence from common lab environment vibrations.The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. These units are made to order in many different gauge lengths and measuring ranges.The extensometer comes with a signal conditioner. The output is an analog DC voltage, factory calibrated with the extensometer to 0 to ±10 VDC typically. They are readily interfaced with most existing test controllers, and may be directly connected to data acquisition systems and chart recorders. Bringing the signal into a spare DC input channel (or external input) on the test controller allows the extensometer to be used for strain controlled tests like low cycle fatigue.
-
Product
Bi-Axial or Axial Averaging Extensometers
Model 3560
-
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
-
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
Product
Circumferential Extensometers
Model 3544
-
Jinan Testing Equipment IE Corporation
Designed for concrete and rock compression testing or for compression tests on other large samples. This model may be used simultaneously with the Model 3542RA axial extensometers.
-
Product
Extensometers
-
Extension measurement is one of the areas that complements our range of UTM program. The result is a comprehensive range of high class variations. The product selection is arranged as follows:*Non-contact extensometers with and without measurement marks.*Contact extensometers: Sensor arm extensometers, incremental and analogue clip-on extensometers as well as extensometers for compression and flexure tests.
-
Product
Universal Testing Systems
-
Instron universal testing systems are versatile, high-accuracy platforms (available in electromechanical and hydraulic variants) designed to perform a wide range of static mechanical tests, such as tension, compression, bend, peel, shear, puncture, and more, on virtually any material. They support force capacities from fractions of a newton up to thousands of kilonewtons, with precision load measurement, high data acquisition rates, and compatibility with thousands of accessories, including a wide range of extensometers, grips, fixturing, and automation solutions to meet demanding quality and throughput standards.
-
Product
Software
-
Tinius Olsen provides software to meet your R&D and quality control needs, working simply, efficiently and accurately. Horizon makes all your testing as effortless as it should be. It carries out your testing and seamlessly integrates with your processes. VSS works with Horizon to control your video extensometer testing.
-
Product
Automatic Extensometer
SIE-560A/560SA
-
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with high accuracy, and provide automated functions that increase testing efficiency and test reproducibility. Ideal for testing a wide variety of materials, including metallic materials, plastics, and composites, the SIE-560A series complies with ISO 527, JIS K 7161, and ASTM D638 standards for plastics tensile testing. In addition, the SIE-560A series supports strain-rate controlled metallic material tensile testing measurements specified in ISO 6892, JIS Z 2241, and ASTM E4
-
Product
High-Temperature Extensometers < 600 °C Capacitive
-
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
Product
Semi-automatic tensile testing machine
-
The controller of this testing machine automatically applies an appropriate load and puts the extensometer between the gauge lines, etc. after the sample is set. It provides measurement with high repeatability.
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
Non-Contact Digital Video Extensometer
TRViewX
-
TRViewX is an advanced non-contact extensometer that offers high-measurement accuracy, is capable of measuring width changes, and is applicable to a wide variety of materials testing applications. In particular, due to the non-contact design, TRViewX is perfect for measuring films, foils, and other thin or narrow materials without affecting the specimen during testing. Furthermore, TRViewX can be used to measure displacements during atmosphere-controlled testing in a thermostatic chamber. TRViewX provides high-accuracy measurements in accordance with ISO 9513 Class 0.5 and JIS B 7741 Class 0.5 for elongation measurements and ISO 9513 Class 1 and JIS B 7741 Class 1 for width measurements. It is compliant with plastic tensile testing standards, including ISO 527, JIS K7161, and ASTM D638, even supporting 75 mm gauge length specimens (type A1 specimens) specified in ISO 527 and JIS K 7161.
-
Product
Sheet Metal r-Value Extensometers
Model 3575AVG
-
Jinan Testing Equipment IE Corporation
Designed for measuring r-values in sheet metal testing, this extensometer averages the lateral strain at two locations. This model may be used simultaneously with the Model 3542 axial extensometer.
-
Product
Static Axial Clip-On Extensionmeters
2630-100 Series
-
The Instron static axial clip-on extensometer delivers precise strain measurement for static tests by quickly clipping to specimens (metals, plastics, composites) with minimal attachment force. Its rugged cross-brace design resists distortion, includes built-in over-extension protection, and meets ASTM E83 / ISO 9513 standards — making it a reliable, high-accuracy option for general and temperature-controlled testing.
-
Product
Universal Testing Machine:UTM Micro
-
Until now, testing of very delicate and small mechanical parts such as bearings, springs, microwires, organic fibers, and micro-electro-mechanical devices was not possible with conventional universal testing machines. But Anton Paar’s universal testing machine, UTM Micro, based on the renowned Anton Paar MCR rheometer, opens up a new world of material testing. The versatile UTM machine’s sensitive MCR technology, combined with its proven modularity, and an integrated extensometer and load cell, allows you to go beyond just tensile testing. You’ll now be able to rise to all kinds of challenges, even in the fields of DMA and optical methods.
-
Product
Automatic Contacting Extensometry
AUTOX750
-
The Instron AutoX750 automatic contacting extensometer offers automated, high-precision strain measurement by motor-driven contact arms to engage specimens—eliminating manual setup while maintaining sub-micron accuracy over long travel. They integrate seamlessly with Instron testing frames and software to reduce operator error, speed cycle times, and ensure repeatable, standards-compliant strain data for metals, plastics, composites, and elastomers.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
Product
Rugged, Long Gauge Length Extensometers
Model 3543
-
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
High Temperature Diametral Extensometers (1000 C)
Model 3580
-
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Auto Calibration for Load & Extensiometer
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
Product
Averaging Axial Extensometers for Large Compression Samples
Model 3542RA
-
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
-
Product
High Temperature Transverse Extensometers (700 C)
Model 7675
-
Jinan Testing Equipment IE Corporation
Designed for transverse or diametral strain measurement in environmental chambers where the entire extensometer must be exposed to elevated temperatures. These capacitive extensometers may be used up to 700 C (1300 F) without any cooling.
-
Product
Deflection Gauge Extensometers
-
AMETEK Sensors, Test & Calibration
We supply a wide range of deflection gauge extensometers ideal for measuring deformation in three and four point bend tests and in compression testing applications.
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Contactless Video Extensometers
-
Jinan Testing Equipment IE Corporation
Deformation measurement of samples during material testing with use of the Video extensometer MercuryRT allows applying multiple virtual probes (Movement Sensors)on markers and advanced image featuresto be tracked, including the natural pattern of the sample surfaces.The common resolution of standard system is within 500 nm and 5 m. The system fulfils class 0.5 or B-1 of classification according to ISO 9513 and ASTM E83. In certain camera use case, the system resolution reaches the level of 100 nm - 500 nm and system fulfils the class 0.2. The strain resolution can reach 10 microstrains. Material testing,Component testing ,FEA validation,Vibrography .
