Automated Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance.
See Also: ATE
-
Product
Flying Prober Test System
QTOUCH1404C
Test System
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
Product
Automated Test Interface
ATI-100
-
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP
-
SCOT MXP measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time in various configurations. The MXP has a special mode to measure Pre-Insertion Resistor (PIR) closing time
-
Product
Massively Parallel Parametric Test System
P9001A
In-Circuit Test System
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
Product
High Voltage Test Equipment
-
A hipot test is conducted by ensuring no current flows from one point to another on a circuit. A hipot test will take two conductors that should be isolated from one another and passes a high voltage between the two points. The current which flows between these points is then measured. If too much current flows, this would indicate that the points are not well isolated and the test will fail.
-
Product
Refurbished Equipment
-
These instruments have been fully refurbished at PHI and performance has been brought up to the original specifications. All instruments are backed with the same 1-year warranty as a new instrument. Prices include installation, warranty, and training. Once the warranty expires, a wide range of service contracts are also available to meet your requirements. Below is a list of refurbished instruments currently available.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
Automation Testing Services
-
Alphabin Technology Consulting
Delivering applications at lightning speed is as crucial as the high quality of the product, automating repetitive tasks with test automation services.
-
Product
Automated Regression Testing
VectorCAST/Manage
-
VectorCAST/Manage is an extension of the VectorCAST family of unit and integration testing tools, answering all problems associated with manual testing and providing confidence in final results.
-
Product
Assembly Automation
-
JRT Photovoltaics GmbH & Co. KG
Piloted-driving, electromobility, connected cars – the automobile industry is currently undergoing a profound transformation. Today, such future trends pose new production challenges. Intelligent and agile production machines are in demand. Processes must be highly flexible in term of both time and space. Jonas & Redmann offer modular assembly platforms that meet the very highest requirements.
-
Product
Equipment
-
Based on a proprietary light engine, our solar simulation equipment delivers perfect and continuous artificial sunlight 24/7, allowing for accurate stability and performance assessments of solar cells at laboratory and industrial scales.
-
Product
Lab Testing Equipment
-
Construction materials testing laboratories should be equipped with all of the accessories and consumables for conducting the required tests. Not least because any delay in testing can result in a costly delay in a building project. However, the cost of this equipment is negligible in comparison with project costs so it makes sense to ensure that sufficient stock is in place, both before and during the construction project.
-
Product
Image Sensor Testing
IP750Ex-HD Family
Test System
The IP750EX-HD has been the test platform that has enabled the industry to manufacture high quality CCD and CMOS image sensors, and it is the most economical platform to meet the needs of newer technologies such as Time of Flight (ToF) sensors. When you use a smartphone, high performance digital still camera, or in-home security and surveillance system, these applications have image sensors most likely tested by Teradyne’s IP750ExHD.
-
Product
Optics Test Equipment
MTF Measuring Systems For Industrial Applications
-
Optik Elektronik Gerätetechnik GmbH
The MTF (modulation transfer function) is a recognized quality criterion for the imaging quality of optics. OEG GmbH develops and manufactures computer-controlled, fully automatic measuring systems for MTF and other parameters for quality assurance in optics production, incoming goods inspection, research and teaching.
-
Product
Automated Server & Application Testing / Certification Solution
VersaTest Family
-
VersaTest is a powerful family of software testing solutions that work at the message level to perform machine interface-level testing of systems and server-based applications. Though used by testing professionals across industries, its widest use in is the testing of mission-critical payments applications and networks in the retail and banking industries, such as those found in the processing of POS (point of sale) and ATM transactions. Its flexibility has also enabled it to be successfully used in other areas from the testing of healthcare information systems and telecommunication networks all the way to to air traffic control systems - anywhere that computers exchange messages, regardless of the form, VersaTest has been successfully used.
-
Product
Rock Mechanics Testing Equipment
-
Rock mechanics is the part of geotechnical engineering that studies the behaviour of rocks under variable physical and environmental conditions. Testing is undertaken to enable the prevention of geotechnical failure such as shearing, by measuring the behaviour of rocks for compliance with regulations, design specifications and quality control standards.
-
Product
Surplus Test Equipment
-
Our Surplus Test Equipment Department carries a wide variety of used/refurbished avionics/instrument test equipment, panels, tools and other testing systems and accessories. We offer a wide range of aerospace test equipment and tooling for ramp and bench testing in addition to a host of services such as pre-sale and post-sale technical support, repair and calibration. As an FAA certified repair station (PK4R443M) we have an in-depth understanding of our clients' needs and our quality system satisfies their most stringent requirements. Whether you are a small avionics shop, a large MRO, an airplane manufacturer or an airline maintenance facility, ASI has the right solution for your ground support test equipment. Our knowledgeable and dedicated staff stand ready to assist you with all your aircraft electronics test equipment needs.
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
Automation Control
-
Schweitzer Engineering Laboratories, Inc.
Monitoring and controlling substation power systems requires comprehensive solutions. SEL’s complete solutions and hardened devices help maintain system stability with deterministic control; streamline access to valuable IED data, communications processors, and field devices; and improve visualization and control with local HMIs and access to SCADA systems.
-
Product
Asphalt Testing Equipment
-
ELE international manufactures a comprehensive range of field and laboratory asphalt testing equipment to ensure compliance with quality and performance specifications. Traditional methods of binder content analysis involved the use of solvents, but due to environmental concerns ELE has developed an Asphalt Binder Analyser which uses an ignition method and thereby avoids the use of harmful solvents. Loss on heating and a rolling thin-film oven are used for testing bitumen, flash and fire point are measured with the Cleveland Flash Cup Apparatus, and the Ring and Ball test enables the measurement of the softening point.
-
Product
Spray Equipment
-
Engineered for the most demanding automotive and industrial refinishing bodyshops through to the smallest independent workshop - whatever your spraying requirements, Sagola has the gun you need.
-
Product
Test Automation Solution
CONFORMIQ TRANSFORMER
-
Conformiq Transformer shortens the path to test automation, simplifies model-based testing (MBT) adoption using existing methods, and automates manual test execution. Along with Conformiq Creator, which generates executable test cases, scripts and documentation from models, it automates and transforms test design, extending the Conformiq 360° Test Automation™ solution for complex system testing at the speed of development.
-
Product
Automation Equipment
-
Through its SMART and COMPACT automated equipments, RECIF Technologies proposes a complete offer for wafers/substrates atmospheric handling, and provide IC manufacturers with innovative and configurable solutions responding to wafers and frames handling requirements.
-
Product
Imaging Automation
XImage
-
Whether you are a Microsoft Authorized Refurbisher, Microsoft Registered Refurbisher or just getting started in refurbishing, Erasure, Test and Re-Imaging are a must to get the most out of your assets. The problem is that until now, this required a big work force. One group to perform the testing and visual inspection, one group to perform erasure, someone to create and manage all your images and substantial knowledge on how to automate and deploy those images. Even with all of these bases covered, it can still be a complicated, time consuming task. Not to mention the fact that it is typically done in a separate process from data erasure, testing and auditing.
-
Product
Neonatal Test Equipment
-
Our lineup of neonatal test equipment is a complete NICU quality assurance solution to ensure infant safety.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
Footwear Test Equipment
-
AVENO footwear testing equipment including leather tester, shoes tester, rubber tester, and velcro tester, related to water resistance test, abrasion test, flexing test, impact test, fatigue test, and etc. of all shoes material.
-
Product
Automated API Testing
-
TestingWhiz is an API test automation tool that helps you test whether your application communicates and responds correctly to perform a workflow by verifying web services connected to them.
-
Product
Laboratory Equipment
-
Helping researchers and scientists increase efficiency and productivity, every day. We are a leading supplier of laboratory equipment and analytical instruments for scientific, R&D, educational laboratories across the globe. We back all our lab equipment products with free and unbiased technical assistance to help you solve your application needs. LESS -
-
Product
Safety Testing Equipment
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD provides safety testing solutions and safety testing equipment, including UL1439 Sharp Edge Tester, Range Hood Air Volume Measurement Test Device, Spring Impact Hammer Calibration Equipment, Scratch Resistance Test Machine, Adjustable Universal Energy Spring Impact Hammer, IK Vertical Hammer Impact Tester. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
