Automatic Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance. Also known as: ATE
See Also: Automatic Test Systems, ATE
-
product
Power Module Tester
The Power Module Checkout ATE is developed for testing DC-DC Power modules typically utilized in India's space program. The DC-DC converters are exhaustively tested for all design parameters including supply voltage range, line and load regulation, efficiency, ripple, noise, transient response and so on. Special power sources and loading mechanisms are deployed to enable testing of various types of power modules.
-
product
PXI Dual 12x4 Matrix, 1 Pole Switching
40-511-021
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.803-08
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXI 2 Banks of 40 Channel 2 Pole MUX
40-615-022-2/40/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
PXI 4 Slot BRIC 184x8 1-Pole (4 sub-cards)
40-560A-021-184X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
ATE Products
Microtest ATE portfolio presents special patented solutions to reduce the cost of test.Our innovative ATE offers high multi-site efficiency, zero footprint and lower power consumption.We’re able to drastically reduce the engineering phase time also for special solutions tailored on customers’ needs.
-
product
PXI 2 Amp MUX, Single 4-Channel 8-Pole
40-635-104
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXIe MW Signal Generators
The PXIe platform can be used as a single desktop unit or easily scaled up to multiple channels, while keeping the required space to a minimum. With frequency ranges of 8GHz, 20GHz or 40GHz, excellent signal quality and integrity and fast switching speeds. It's designed to meet today’s most demanding applications in ATE, production or embedded systems.
-
product
PXI 8 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-121-64X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
40-635A-007
The 40-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
RF/Microwave ATE Systems
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
product
PXI High Density Mux 24 Channel 4 Pole
40-670A-021-24/4
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
Advanced Power System - DC Power Supply, 20 V, 100 A, 2000 W
N6971A
The N6971A is designed for automated test equipment (ATE) applications where high performance is critical.
-
product
PXI 4 Slot BRIC 60x8 2-pole (2 sub-cards)
40-561A-022-60X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 4 Slot BRIC 22x16 2-pole (2 sub-cards)
40-562A-022-22X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 5 Banks of 32 Channel 1 Pole MUX
40-615-022-5/32/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Dual 16x8 1-Pole High-Density PXI Matrix Module
40-520-205
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 4 Slot BRIC 44x8 2-pole (2 sub-cards)
40-562A-022-44X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
DC Power Module, 60V, 5A, 300W
N6775A
The Keysight N6775A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
product
PXI Multiplexer Single 32 Ch 2 Pole
40-630-022-32/2
The 40-630 series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.Each module is configured into one of the configuration modes. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 4 Slot BRIC 60x16 1-Pole (4 sub-cards)
40-561A-021-60X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Inline Test Handler W/Bypass
6TL36
The 6TL36 test handler is the first ATE handler on the market that easily integrates the radio frequency tests into mass production lines.The modular approach of the 6TL36 offers the possibility of adding handlers together for a work in parallel that reduces the cycle time and saves costs as well as space when compared to traditional parallel solutions. Therefore, the system can be ordered with only one conveyor, with two conveyors (bypass or dual-line), and with three conveyors (Retour conveyor).
-
product
Rack Mount MW Signal Generators
The Rack Mount platform of the Lucid signal generator is designed to offer maximum channel density at minimum cost of space. Offering up to 4 phase coherent channels in a 19” 1U box, the rack mount platform is by far the best in its class for signal density. Featuring fast switching speed, superior signal integrity and purity, removable memory card for maximum security, all the necessary modulated signals for analog communication systems, built in LAN and USB interfaces, this platform meets today’s most demanding specifications, needed for ATE and production lines.
-
product
PXI 4 Slot BRIC 44x16 1-Pole (4 sub cards)
40-562A-021-44X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
40-635A-008
The 40-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI Very High Density Mux 99 Ch 2 Pole
40-670A-022-99/2
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.822-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXI 2 Amp MUX, Quad 16-Channel 1-Pole
40-635-008
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
