-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
SINE (Sinusoidal) Targets & Arrays
-
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
-
Product
Radar Test System
UTP 5065
Test System
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
Automotive Radar Transceivers
-
Driver assistance systems use radar sensors in various counts and configurations. The data provided by the radar sensors is used in applications such as blind-spot detection, autonomous emergency braking, and adaptive cruise control, to increase safety by enabling vehicles to identify and avoid potentially dangerous situations.
-
Product
Guided Wave Radar
-
A top-down, direct sensing technology that uses low-energy microwave pulses sent down a probe to accurately detect the boundary between two immiscible liquids.
-
Product
Radar Flow Meter
HR.FSL-1
-
HighReach Measuring & Controlling System Co.,Ltd
It is designed for combination with water flow detection for hydrological monitoring. It is designed for surface flow monitoring of natural rivers, canals/cules/pipes, etc., and flood monitoring in urban Seasons Flood, SUCH AS Low-lying Areas. Water Flow, Flow Rate Monitoring Drain, etc. of The Product Planar absorbs The 24GHz Radar Technology of a microstrip InnoSenT of Germany, and Adopts ITS own Back-End Processing Technology to Accurately The Water Extract Flow Speed , which can realize non-contact and unmanned automatic monitoring.
-
Product
Weather Radar Panel for Primus
TA-3B
-
A weather radar panel similar to the TA-3 panel but with more specific test jacks for testing the Primus 300/400 series radars. Specific test jacks for power supply, antenna and indicator.
-
Product
Elevated 1.68 (4.00) - 7.00 (198.00) Bead Probe
BTP-1HF-7
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Radar solutions for mechanical engineering
-
With OndoSense radar sensors you will increase the productivity of your industrial systems, reduce unplanned maintenance times for your machines and automate the work processes in the Industry 4.0.
-
Product
Radar Front Ends
FMCW
-
The transmit signal is derived from an external VCO signal, internally multiplied, which also acts as the LO for the receive mixer. The resulting IF is conditioned for gain and filtering as required. The IF also contains an industry leading IF noise figure, especially in the frequency range below 500MHz. Custom designs available, visit our custom design page for more information.
-
Product
Elevated 1.68 (4.00) - 7.00 (198.00) Bead Probe
BTP-1F-7
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Range-Doppler Target Generators
ATG9100
-
The ATG-9100 is an example of a laboratory-quality instrument that will simulate complex target motion. Microwave signals from the speed camera enter the instrument through an integrated antenna which is then downconverted and digitized. Target simulation data is added to the digitized signal to provide range and Doppler information. The modified digital data is then converted back to an IF and upconverted to the original microwave frequency of the speed camera and radiated back through the antenna. Since the ATG-9100 can be phase-locked to an external 10 MHz reference standard, this instrument is suitable for use as a calibration standard for speed cameras.
-
Product
ACCUplace Dot Distortion Target
AP-DD Series
-
All machine vision lenses will show some type of distortion. Minimizing or correcting that distortion is crucial in most applications. The ACCUplace Dot Distortion target is designed to detect the presence of both barrel/pincushion distortion as well as alignment distortion that causes the keystone effect. The precise amount of distortion is determined from an array of precisely placed dots in a regular array. The results can be used to correct for any distortion that occurs within the optical system. The AP-DD is offered on three standard substrates; Chrome on Glass (CG) Opal (OP) and Photo Paper (RM).
-
Product
Direction Sensing Radar
Stalker DSR
-
Direction Sensing Technology • Same-Lane Tracking Operation - Simple, Accurate, and Automatic• Stationary Direction Control • Strongest and Faster Targets Displayed • Strongest and Faster Targets Can Be Locked • True Waterproof Digital Antenna Communications • Small Detachable Display Unit • Software Upgradeable • Interfaces with Cameras & Computers • 3 Year Full Warranty
-
Product
Automotive Radar Testers
-
Rohde & Schwarz provides automotive manufacturers, components suppliers and test houses with innovative, cutting-edge solutions which bring realistic test scenarios from the road to the lab and production line.Our range of solutions include a signal generator-based target simulator, a radome & bumper tester and an anechoic automotive radar test chamber allowing for over-the-air (OTA) testing. These solutions are at the heart of the development of advanced driver assistance systems (ADAS) with its safety-critical features such as emergency braking. Using T&M solutions by Rohde & Schwarz enables a thorough testing of chipsets, sensors and modules at each phase from development and conformance to production.
-
Product
Radar solutions for the metal & steel industry
-
Our reliable radar sensors enable the high-precision width measurement and thickness measurement of semi-finished metal, the contactless level monitoring of molten metal and the steel strip positioning in the coating line.
-
Product
Osiris Dual Channel Radar Interface
-
Curtiss-Wright Defense Solutions
Osiris is a high-performance, dual-channel radar interface board that accepts and processes analog and digital radar signals and provides a PCI interface to applications. Osiris comes from a long history of radar interface products at Curtiss-Wright Defense Solutions, with interfaces to support many legacy and modern radar types.
-
Product
HPx-346 Analogue to Network Radar Converter
-
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
-
Product
Pulse Radar Reference Test Solution
-
Compact Reference Solution with ADP7104, M8195A, WR15CCU, WR15CCD, N5183B combines commercial off-the-shelf COTS modular hardware and software from Guzik, Keysight Technologies, KJ Microwave and Virginia Diodes, which provides a flexible testbed for radar waveform generation and analysis. Generate and analyze pulse radar waveforms. Pre-correct waveforms for overall channel response. Supports many topologies for radar transmitter / receiver testing (IQ, IF, RF, microwave, millimeter-wave).
-
Product
Radar Distance Sensors: Applications & Products
-
Powerful radar distance sensors are needed to measure accurately and reliably even in complex industrial environments. With its unique measurement precision and real-time measurement rate, OndoSense distance radar sensors are ideal for automation in industrial applications with harsh conditions.
-
Product
Radar Detectors
-
histler''s FDSR (Field Disturbance Sensor Rejection), the most recent advancement to combat new vehicles equipped with Frequency-Modulated Continuous Wave (FMCW) K band blind spot and collision avoidance devices that clutter nearly all of K band causing a normal radar detector to alert continuously.
-
Product
Elevated 1.68 (4.00) - 7.00 (198.00) Bead Probe
BTP-1HC-7
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Standard IR Target Projectors
-
Santa Barbara Infrared’s 14000Zi Series reflective infrared target projectors are turnkey test systems for electro-optical (E-O) testing of FLIRs and other infrared (IR) imaging systems. The standard target projectors are assembled from SBIR’s STC Series Collimators, Infinity Blackbodies and 300 Series Target Wheels. SBIR also offers a standard athermal target projector with a 5.7° field of view (FOV).
-
Product
NI Vehicle Radar Test System
Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
High 1.50 (43.00) - 9.60 (272.00) Long Travel Bead Probe
BPLT-1F-9.6
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,450Overall Length (mm): 36.83Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, High Spring: 350 mil / 8,89 mm
-
Product
High 0.75 (21.00) - 8.00 (227.00) Long Travel Bead Probe
BPLT-25C-8
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
Ground Penetrating Radar
-
RD1100 and RD1500 both feature internal GPS and high resolution touch screens. For connectivity, both offer on-board Wi-Fi and a USB port. Additionally, the RD1500 allows users to create depth slices and review their locate path on screen while on site, and selectively enhance shallow/small, medium depth/size, or deep/large targets using the proprietary FrequenSee™.
-
Product
Multi-Role, Low-SWaP Laser Target Designator
StormCaster™-DX
-
The Teledyne FLIR StormCaster™-DX is a multi-role, low-SWaP laser target designator payload designed to affect the STANAG-compliant terminal guidance of laser guided munitions. StormCaster-DX is tightly integrated with the R80D SkyRaider™ UAS to leverage its class-leading payload capacity, multi-mode operations (tethered/untethered & mounted/dismounted), and AI-CV-based targeting capabilities.
