-
Product
Network Impairment Simulator
-
Testing system performance under realistic network conditions requires the introduction of impairments that could be expected to be seen on networks, especially public networks which are uncontrolled. There are a number of ways to do this. A basic method is to use network simulation devices that can emulate conditions expected to be encountered.
-
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Radar Level Transmitter
DR6500
-
The Drexelbrook DR6500 is a two-wire open air radar level transmitter for measuring level in applications with powder and dusty atmosphere.
-
Product
Servicing and Testing of Search and Rescue Radar Transponder
SART
-
The Search and Rescue Radar Transponder as a part of GMDSS is a subject to annual test during radio survey. The annual testing of SART is recommended due to SOLAS regulation IV/15.8.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).Also Marine Orders require that a radar transponder must be inspected, tested and have its batteries replaced at intervals specified by its manufacturer.
-
Product
Radar Sensors & Systems
-
Emerging radar applications are touching a diverse range of applications, including automotive, industrial, agricultural, and infrastructure. Radar system solutions are highly specialized and able to meet the demanding needs for accuracy, real-time performance, and reliability in extreme weather conditions.
-
-
Product
MHG Solar Simulation
-
Atlas Material Testing Solutions
Filtered MHG lighting is a mature technology used since the 80’s for larger solar simulators inside environmental test chambers. MHG lamps are filled with a mixture of mercury, halides and rare earth elements which vaporize during ignition, generating a plasma. After a few minutes, the plasma reaches thermal equilibrium and emits a quasi-continuous spectrum (when properly filtered) similar to global solar radiation.
-
Product
Network Simulator
Fiber Lab 3200R
-
The Fiber Lab 3200R from M2 Optics is the latest innovation in a successful series of customized, packaged optical fiber platforms. Similar to the original Fiber Lab 3200 in terms of capacity and performance, this chassis has been re-designed specifically for users that wish to showcase their test fiber during system demonstrations, customer visits, and other common applications.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel With V/I Readback
41-752A-011
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Radar Altimieter Test Panel for ALT-50/55
TA-55
-
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.
-
Product
Diagnostic Simulation
Stage
-
STAGE simulates aspects of Diagnostic, PHM and ISHM Engineering, showing the support capabilities of a System during its useful lifetime. Many types of analysis can be performed on STAGE, including Testability, System Reliability & Mission Success, Sustainability, and Logistics Resource Allocations.
-
Product
Regenerative Grid Simulator
61800 series
Simulator
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
Product
Solar Simulators
TriSOL CPV
-
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Radar Systems
-
A radar system utilizing electronic-computer techniques whereby raw data is used to track an assigned target, compute target velocity, and predict its future position without interfering with the scanning rate.
-
Product
Simulation Software
-
Gain the ability to accelerate product design or analysis in any field of engineering with the most comprehensive software suite, expertly spanning the entire range of physics disciplines.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
HPx-346 Analogue to Network Radar Converter
-
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
Product
IMU MODELING AND SIMULATION
-
CAST Navigation’s INS systems provide high rate inertial data with exceptional fidelity to support the integration and testing of today’s complex EGI and GNSS/INS navigation systems. The CAST system is designed for optimal performance when the inertial sensor and GNSS receiver are either loosely, tightly or ultra-tightly coupled, or when an INS aiding source can be utilized by any other type of device.
-
Product
Molding Simulation Software
Moldflow®
-
Engineers and analysts use Moldflow software for plastic injection molding simulation to improve plastic part designs, injection mold designs, and manufacturing processes.
-
Product
Complex Environment Simulator
-
Complies with IEC60904-9 solar simulator/classes B and C. Includes integrated temperature and humidity controls, allowing the output measurement testing and the complex durability testing to be conducted by one unit. The work size and the temperature/humidity control range, etc. can be customized.These chambers are available at Iwasaki for testing your samples; please contact your local agent for details.
-
Product
Radar
VEGAPULS
-
In continuous non-contact level measurement with radar, the sensor sends microwave signals towards the medium from above. The surface of the medium reflects the signals back in the direction of the sensor. Using the received microwave signals, the sensor determines the distance to the product surface and calculates the level from it.
-
Product
Space Simulators
A6H Series
-
Bemco offers up-to-date space simulators incorporating all of the preferred features needed for reliable combined temperature and high vacuum testing. The A6H series includes a fully integrated and appropriately sized PCL-III Portable Liquid Chiller utilizing liquid nitrogen for cooling. The PCL-III is mounted within the A6H system structure and permanently attached to the chamber thermal shroud. Mechanical cooling is available as an option.
-
Product
Pulse Radar Reference Test Solution
-
Compact Reference Solution with ADP7104, M8195A, WR15CCU, WR15CCD, N5183B combines commercial off-the-shelf COTS modular hardware and software from Guzik, Keysight Technologies, KJ Microwave and Virginia Diodes, which provides a flexible testbed for radar waveform generation and analysis. Generate and analyze pulse radar waveforms. Pre-correct waveforms for overall channel response. Supports many topologies for radar transmitter / receiver testing (IQ, IF, RF, microwave, millimeter-wave).
-
Product
Power System Simulator
F6150e
-
This power system simulator performs the simplest through the most complex tests. Meeting all your protective relay testing needs, the F6150e is available in different configurations.
-
Product
Barometric Pressure Simulation
SimBARO
-
Embedded and Integrated GPS/Inertial navigation systems require an altitude reference data input provided by a barometric pressure altimeter to reduce vertical plane errors inherent within inertial systems. Spirent’s SimBARO product offers a simulated source of barometric pressure altitude data and is available as an add on to SimINERTIAL, Spirent’s Inertial Measurement Unit (IMU) and Embedded GPS/Inertial navigation system (EGI) test tool.
-
Product
Altitude Simulation
MEDAS
-
The MEDAS system is a compact altitude simulator that reproduces a wide range of environmental conditions. It allows for testing light- to heavy-duty vehicles, including Non-Road Mobile Machinery (NRMM). It is ideally suited for a range of testing applications, such as durability, RDE replication, emission tests and mapping as well as tests from component to vehicle level. The patented technology inside the MEDAS system allows dynamic changes on the simulated atmosphere with high accuracy. The system can also be moved between different test cells due to its compact design.
-
Product
4D Imaging Radar Chipset Solution
-
Through enhanced FMCW technology, Arbe’s chipset technology transmits and receives signals from multiple antennas. By converting information from time to frequency domains (FFT), Arbe provides a 4D image with unparalleled element density in high azimuth and elevation resolution while simultaneously sensing the environment in long range with a wide field of view in real time. Additionally, Arbe technology reduces sidelobe occurrence levels close to zero, resolving range-doppler ambiguities and avoiding interference from other radars.
-
Product
Camera Link Simulator
CLS-221
-
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
