Very Fast Transmission Line Pulse
tests simulate IC or SOC ESD events with pulse lengths < 10ns and deep sub nanosecond rise times. Also known as: VF-TLP
See Also: Transmission Line Pulse, TLP
-
Product
Single-in-Line Reed Relays
Series 116
-
SIL relays - Smallest board area. 1A version requires 0.15 x 0.27 inches .(3.8mm x 6.8mm). 1 or 2 switches with 10 Watts rating. 5 or 12 Volt coils with optional diode
-
Product
Line Automation Equipment
5000 Series In-line Handler
-
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
8 Port Phone Line Simulator (FXS) Adv
CH-8FXS-A
-
This unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
High-end Transmission Electron Microscope
CryoARM
-
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
-
Product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-D/10/8
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Fast Response Flow Controller for Medium Flow
HFM-301 / HFC-303
-
The HFM-301 / HFC-303 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-301 / HFC-303 services a wide variety of applications. Cleaning for oxygen service is available.
-
Product
Field-installation Type Simplified Fluoride Ion Concentration Meter(Two-Wire Transmission)
HC-300F
-
HC-300F is connected to a fluoride ion electrode (1009) to detect free fluoride ions in the sample water.(Total fluorine is not detected.) It is suitable for fluoride ion monitoring in effluent from factories, e.g., those of semiconductor FPD and glass manufacturers.
-
Product
PXI/PXIe Very High Density Multiplexer, 24-Channel, 8-Pole
40-675B-002-24/8
Multiplexer Module
The 40-675B-002-24/8 (PXI) and the 42-675B-002-24/8 (PXIe) are 24-channel, 8-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Super Fast Gang Industrial Universal Programmer
48Pro2AP
-
The Dataman 48Pro2AP is a super fast industrial universal programmer with ISP capabilities and USB 2.0 connectivity • Optimised for use in automated handlers and ATE machines • Over 71,000 devices supported with new devices added monthly • Mechanically stable case design with multiple fixing points • ISP capable using the JTAG interface • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
PXIe Source/Measure Unit, 15 MSa/s, 1 PA, 60 V, 3.5 A DC/10.5 A Pulse
M9602A
Source Measure Unit
The Keysight M9602A is a PXIe SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
AC Line Separators
ALS-2
-
Standard Electric Works Co., Ltd
● x10 Model allows for more accurate measurements of low amperage devices.● Direct reading x1 mode.● 4mm Voltmeter input jacks.● Intergrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
Product
Extenders & Line Drivers
-
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
Product
System Tests Radar Pulse Stability
PN9002
-
Noise eXtended Technologies S.A.S.
The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.
-
Product
4 Channel 1.0 ~ 17.0 Gb/s Pulse Pattern Generator and Error Detector
CA9806
-
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
Product
Nanosecond Pulsed Lasers
-
Our nanosecond pulsed lasers feature pulses in the ns range. For picosecond and femtosecond lasers please see Ultrafast Lasers.
-
Product
Panel-mount Type Conductivity Meter (Four-Wire Transmission, For Wide Range)
HE-960HI
-
HE-960HI is a wide-range type sanitary electric conductivity meter that can measure over a wide range from manufacturing water up to 500 mS/cm, and enables advanced concentration management through abundant outputs. It connects conductivity sensor (FES-220/310). Cleaning-in-Place (CIP) terminal management and a reduction in cleaning solutions is also achieved through accurate surface detection.And we have developed a lineup of electric conductivity sensors that can be used in conjunction, from the conventional insertion type to the flow-through type with improved cleaning and sanitary properties.
-
Product
Field-installation Type ORP Meter (Two-Wire Transmission)
HO-300
-
HO-300 connects ORP sensor and measures ORP and temperature in the sample water. It is suitable for neutralization reaction treatment management of aeration tank, denitrification tank, etc.
-
Product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
-
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
Product
Logger version optical fast DO sensor
RINKO I / I D
-
Rinko I is an autonomously deployable data logger with a fast response optical DO sensor. The instrument and the software with various operating mode offer flexible observations in the field. The small-sized and the self-contained unit with batteries and a data logger can be easily integrated on platforms (e.g. CTDs). Rinko ID has a depth sensor, allowing for DO vertical distribution measurements.
-
-
Product
Field-installation Type Turbidity Meter (Four-Wire Transmission, For Wide Range)
HU-200TB-W
-
HU-200TB-W is a turbidity meter developed to continuously measure turbidity in processes with large turbidity changes, such as water intake and sedimentation tanks in water supply plants. It employs transmission 90-degree scattered light method and is ideal for monitoring changes in processes with large turbidity changes from low range (10 degrees) to high range (2000 degrees). An electric wiper cleaning can be installed as an option, and long-term stable measurement is possible by periodic cleaning.
-
Product
12-Watt Pulsed FAYb Fiber Laser
LP-V Series
-
Panasonic Industrial Devices Sales Company of America
The LP-V series is a 12-watt, pulsed fiber laser.Characteristics:- Very high resolution- Fine marking area- Small air cooled head
-
Product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
KATANA & PILAS Pulsed Diode Lasers
-
With external trigger functionality, nano- to picosecond pulse duration, and a wide range of wavelengths, the KATANA & PILAS series are our most versatile offering.
-
Product
Xi Series Compact Line Infrared Camera
-
The Optris Xi Compact Line is a revolutionary series of infrared cameras that usher in a new era of affordable, high-quality, and precise non-contact thermal imaging. In infrared imaging, the Optris Xi Compact Line shines with its capacity for non-contact temperature measurement. Operating within a broad infrared wavelength range, this forward-looking infrared imager captures data beyond the visible spectrum, allowing for accurate surface temperature measurements.
-
Product
PXI/PXIe Very High Density Multiplexer, 198-Channel, 1-Pole
42-675B-002-198/1
Multiplexer Module
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
Precision Source / Measure Unit, 1-Channel, 10 FA Resolution, 210 V, 3 A DC / 10.5 A Pulse
B2911B
Source Measure Unit
The Keysight B2911B precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
Product
Green Cross Line and Point Laser
Lino L2P5G
-
The Leica Lino L2P5G uses the latest green laser technology which projects clearer and crisper laser lines at exact right angles to one another. This allows for the highest accuracy of detailed interior tasks. The working range is up to 35 meters depending on the lighting conditions, and can easily be extended up to 80 meters using the laser receiver Leica RGR 200.
