Data Acquisition Systems
sense, log and store information. Also known as: DAS
See Also: Data Acquisition, PCI Data Acquisition, DAQ
-
product
Temperature Sensor
ITS-7025
The ITS-7025 Temperature Sensor was developed to monitor the temperature of liquid-cooled klystron amplifiers. The sensor is designed to clamp directly to the cooling pipe and provide an analog voltage output from 0 to 10 VDC corresponding to 0 to 100 degC with 2 degC accuracy. Two analog outputs are provided; one for connection to a remote data acquisition system, and a second for local service monitoring. A single +28 VDC (other voltages available) powers the sensor which draws less than 100 uA.
-
product
PXI High Density Multiplexer, 4-Bank, 20-Channel, 2-Pole
40-615A-008
The 40-615A-008 is a 4-bank, 20-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 1-Pole
40-615A-017
The 40-615A-017 is a 2-bank, 40-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI 2A Multiplexer, 1-Bank, 128-Channel 1-Pole
40-614-015
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
40-635A-008
The 40-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Data Acquisition & Control Systems
Ensuring you make the most of your testing equipment, SuperFlow offers a variety of dynamometer data acquisition and dynamometer control packages for your Engine, Chassis or Transmission dynamometer application. Contact SuperFlow to discuss which instrumentation system and related accessories are right for you, and turn your testing challenges into success.
-
product
Dynamometer Controls, Data Acquisition Systems and Instrumentation
Whether you want a basic engine dynamometer configuration that provides torque, rpm and power or need an advanced, full-featured test and measurement software package, Taylor has a data acquisition system that will serve your unique application without breaking your budget. Contact Taylor to discuss which instrumentation system and related accessories are right for you, and turn your testing challenges into success.
-
product
PXI/PXIe Very High Density Multiplexer, 10-Channel, 16-Pole
40-675B-002-10/16
The 40-675B-002-10/16 (PXI) and the 42-675B-002-10/16 (PXIe) are 10-channel, 16-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
product
Current to Digital
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
product
PXI 2 Amp MUX, Dual 32-Channel 1-Pole
40-635-005
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI High Density Multiplexer, 47-Channel, 2-Pole
40-640A-022-47/2
The 40-640A-022-47/2 is a 47-channel, 2-pole MUX and is part of a series of high density multiplexer modules featuring a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 5 Banks of 16 Channel 2 Pole MUX
40-615-022-5/16/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
product
Single 32x6 1-Pole High-Density PXI Matrix Module
40-520-301
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 5 Banks of 16 Channel 1 Pole MUX
40-615-021-5/16/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Isolated Hall Effect Current Sensors
Isolated Hall Effect current sensors provide accurate high bandwidth current sensing. Vektrex offers models to 320A. For use, the 50-ohm voltage output is connected directly to an oscilloscope or data acquisition system. VCS sensors are magnetically isolated like clamp-on oscilloscope probes. With secure cable attachment, repeatability is ensured.
-
product
PXI Very High Density Multiplexer, 198-Channel, 1-Pole
40-675A-002-198/1
The 40-675A-002-198/1 is a 198-channel, 1-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
48-Channel Seismometer
FlashSeis48
ZZ Resistivity Imaging Pty. Ltd.
48 channel seismic data acquisition system.
-
product
DAQ User Interface Software
DAPstudio 3.00
If you need to deliver a data acquisition system quickly and you want to develop a good user interface for it, then download DAPstudio 3.00 and see how that could help. You now can use the latest (full) version of DAP Measurement Studio software from Microstar Laboratories, maker of Data Acquisition Processor (DAP) boards and software, for an unlimited trial period at no charge.
-
product
Differential Amplifier-per-Channel DAS
System 495
NEFF's System 495 uses a proven widerange, guarded differential amplifier -per-channel technique with a dedicated high-speed analog-to-digital converter for each channel. In addition to storing data locally in memory, a subset of each channel's data can selectively be transmitted to the host for monitoring or recording at an aggregate rate of 1MHz.
-
product
PXI High-Density Multiplexer: 64-ch, 2-Wire, 100Vrms/1A, Reed Relays
M9101A
The M9101A, a high-density, 64-channel PXI multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time or, if needed multiple channels can connect simultaneously. Ideal for routing multiple analog signals to a measurement device in automated test environment (ATE) or data acquisition systems. Each channel switches a high and a low for 2-wire switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
product
Communication Devices
Communication devices store and retrieve data acquired by data acquisition systems. These devices facilitate the accessibility, analysis, sharing, and reporting of data. Our available communication devices include both on-site and telemetry peripherals, which can be used in the same application for maximum flexibility, convenience, and reliability.
-
product
16-Channel Anti-Alias Low-Pass Filter Card
AAF-16
The AAF-16 is a 16-channel anti-alias low-pass filter card series for front-end signal conditioning in PC-based data acquisition systems.
-
product
PXI Ultra High Density 64x2 1-Pole Matrix
40-533B-031
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
product
Fluke DAQ 6.0 Application Software
Fluke DAQ 6.0 is a powerful, versatile data acquisition application that provides effortless configuration, data logging, and analysis for the 2680A and 2645A NetDAQ Networked Data Acquisition Unit » and 2680 Series Data Acquisition Systems », plus adds support for the Fluke 2638A Hydra Series III Data Acquisition System/Digital Multimeter » and Fluke Calibration 1586A Super-DAQ Precision Temperature Scanner ».
-
product
Data Acquisition Systems
Encore Electronics manufactures a wide range of analog signal conditioning equipment, including strain gage and pressure amplifiers, frequency-to-voltage converters, thermocouple isolation amplifiers and anti-aliasing filters.
-
product
Software for Recordkeeping Reporting
RegPerfect
Data management is vital to your company's bottom line and mission critical environmental compliance goals. Today's environmental professionals must learn to do more with less when faced with budget constraints, rising operating costs, and staff reductions. TML helps environmental professionals around the world meet these challenges by offering RegPerfect Software.The Teledyne Monitor Labs RegPerfect® software system is a state of the art Data Acquisition Handling and Reporting Sytem. RegPerfect® is the culmination of more than 40 years of experience in the data acquisition system business. The software is designed to comply with the data collection, quality assurance, and reporting requirements of federal and local regulatory agencies. Operating in real time, this rugged platform provides the visibility, connectivity and securityfor all of your environmental and operational needs related to the performance of your Continuous Emission Monitoring (CEM) System. For the most recent updates to the software, please visit the Product Status page.
-
product
Custom Ultra-Fast Data Acquisition Systems
Complete Out-of-Box Data Acquisition Solutions. Fully integrated data acquisition systems shipped directly. Convenient Plug and Play DAQ Environment. Absolutely NO Set-Up time!*. Your choice of chassis. (e.g. Rack, Tower, Shuttle, etc.). Windows™ or Linux Operating Systems available. Multi-Board, High Channel Count configurations..
-
product
Test Automation System for Brake Testing
STARS Brake
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
product
PXI 12x4 Matrix, 1 Pole Screened
40-510-021-S
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
