Level
high or low along a bead it's a measure referenced.
See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test
-
Product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-02
Digital Module
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
Product
800MM 31.5In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles IP54 Standards
DL411
-
Advance Plus Trading Co., Ltd.
Model Number: DL411 Key Specifications/Special Features: 800MM 31.5INCH Digital Level with level bubbles, 2 hand shanks, LCD bright backlight display, IP54 standards 1. 800mm 31.5inch level with 2 bubbles, 800*28*64mm（L*W*H）, net weight: 700g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. 2pcs Handshanks design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.
-
Product
Evaporative Light Scattering Detector
ELSD-LTII
-
The ELSD-LTII utilizes a high-efficiency LED and enhanced digital signal treatment to minimize noise and deliver optimum sensitivity for trace analysis. An innovative cell design also reduces band broadening and allows sensitivity levels below 200 picograms. The high-performance optical detection system can also be used for combinatorial chemistry and high-throughput screening applications. The new Low Temperature Evaporative Light Scattering Detector (ELSD-LTII) is an easy-to-operate, universal detector that identifies analytes with uniform sensitivity regardless of their spectroscopic properties. It is not a spectroscopic detector. Instead, it removes the mobile phase through evaporation and then makes a light scattering measurement of the dried analyte particles.
-
Product
Automatic Transformer Test System
TH2829LX
-
Changzhou Tonghui Electronic Co., Ltd.
Number of Test PIN: 20 ■ Frequency: 20Hz-200kHz, Resolution: 0.5mHz ■ Signal Level: 5mV-2Vrms(Option:2mV-10Vrms) ■ Test Speed: max. 13ms ■ 7-inch TFT LCD display with a resolution of 800×RGB×480
-
Product
Contactors and Motor Starters
-
Mitsubishi Electric Automation, Inc
The MS-N and MS-T series contactors and motor starters offer a high level of versatility for AC and DC control. Its compact design, combined with a wide range of add-on accessories provide adaptability for any motor control, lighting, pumping and conveyor type application. This proven solution provides the highest level of reliability anywhere around the world.
-
Product
Reelsurance
LCi-18 RFID
-
Reelsurance LCi-18 RFID Label Counting and Inspection System with Tagsurance verifies the tag operation sensitivity using communications tests at several frequency and power level combinations with high resolution, stability and high speed. The system provides also accurate label counting, missing label detection and label dispensing of required quantities.
-
Product
Triple Quadrupole Gas Chromatograph Mass Spectrometer
GCMS-TQ8050 NX
-
The Shimadzu triple-quad GCMS-TQ8050 NX is capable of performing unprecedented quantitative GC-MS/MS analyses of ultra-trace amounts, down to the femtogram level. Equipped with a new, highly efficient detector and three forms of noise-reduction technologies, the GCMS-TQ8050 NX has never been more important in industries such as food safety, cannabis testing, forensics, and more.
-
Product
SMT/BGA Rework Station
PDR IR-C3 Chipmate
-
The PDR IR-C3 Chipmate entry level SMT/BGA rework system is specifically designed to be lower cost but still cope with the challenges of repairing today's small, medium sized PCB assemblies.
-
Product
Environmental Chamber
REXMED REC-280
-
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Hall Effect Sensor
-
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Product
Single 16 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-765A-001
Multiplexer Module
The 40-765A-001 terminated single 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
FTT Analysis Software
DS-0321A
-
The DS-0321 is basic software for frequency analysis. With this software, you can resolve time-axis waveform into each frequency, and observe the level of each component. It fits the purpose of resonance frequency observation or careful observation of sound frequency component.
-
Product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
Load Module
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
-
Product
PXI 8 Slot BRIC 30x32 1-Pole (6 sub-cards)
40-562A-121-30X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
AstroAI Digital Multimeter
TRMS 4000
-
WIDE RANGE of tests for AC/DC Voltage, AC/DC Current, Resistance, Continuity, Capacitance, Frequency and Temperature; Tests DiodesPROFESSIONAL LEVEL features include Auto-Ranging capability, and True RMS for measuring both AC Current and Voltage
-
Product
VIS-NIR Cameras
-
Surveillance cameras based on CCD/CMOS/ ICCD/ EMCCD/EBAPS imaging sensors sensitive in visible and near infrared range are widely used in many long range surveillance applications as independent imagers or as part of a bigger multi-sensor surveillance systems. Majority of VIS-NIR cameras are used for day level applications but an increasing number of these cameras is used to enable surveillance in both night and day conditions. In both cases it is important to verify performance of these cameras under varying illumination conditions from very dark nights to ultra bright days. Important missions can fail due to too low sensitivity of VIS-NIR cameras at night conditions (dark, noisy images) or due to too low dynamic at ultra bright day conditions (saturated, blurred images). Next, it is important to use VIS-NIR cameras that generate high quality images in order to achieve maximal effective surveillance ranges.
-
Product
PXI 8 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-121-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Haze Meter
HAM-02
-
Jinan Leading Instruments Co., Ltd.
HAM-02 Haze Meter is a kind of small hazer meter designed according to ASTMD1003—61(1997). It is applying to test the light transmittance,transmission haze, and reflection haze, reflectivity of transparent and semitransparent parallel level material and plasticfilms. Also it is suitable for liquid samples (water, beverage, pharmacy,colored liquid, grease) turbidity measurement. It is the basic instrument for plastic, glass products, all kinds oftransparent packaging films, colored and colorless of organic glass andaerospace, automotive glass and photographic film.
-
Product
Online UPS
LEVELUPS SERIES 10 - 200 kVA
-
LevelUps T3 Series is a true VFI on-line double conversion, three-phase UPS system with Innovative 3 Level Technology and engineered to provide high level of energy efficiency and reliable and robust protection for most demanding industrial and medical environments.
-
Product
HVAC/R Environmental Meter
FLIR EM54
-
The FLIR EM54 is ideal for inspecting and troubleshooting HVAC/R ducting systems within residential, commercial, and industrial facilities. This meter can help you verify that duct inlets and outlets have the specified volumetric flow – a prerequisite to an efficient functional system. Featuring humidity, wet bulb, and dew point functions, the EM54 can measure deviations from proper relative humidity levels. Plus, the included Type-K contact temperature probe is useful to check electric motors and thermal equipment components for proper operating temperatures.
-
Product
Digital Logic ICs
-
Renesas' general-purpose logic devices support the information equipment and computer fields, which demand small size and high performance. With a variety of power supply voltages, functions, and capabilities, these logic devices provide strong support for specialized applications such as bus switching, level conversion, and clock-related applications.
-
Product
CO,CO,light and Sound Measurement
-
Everyone is exposed to different environmental influences in their day-to-day lives. For example, in an average workplace illuminance, sound level, and indoor air quality are all significant factors that influence people's performance and well-being. Testo offers suitable measuring instruments for controlling each of the measurement parameters of lux, sound, and CO2 (for indoor air quality).
-
Product
Calibration and Repair
-
Traceable vibrometer calibration insures a high level of data quality, critically important for many applications in industry, science and medicine. Polytec service engineers ensure fast and efficient equipment calibration that is traceable to national and international standards, intended to be ISO/IEC 17025 compliant.
-
Product
Calibrators
-
A calibrator or process calibrator is used for basic measuring, testing and regulation techniques for setting and verifying test installations and instrumentation. PCE Instruments' calibrator products are lightweight yet made of durable materials. Our calibrator devices are easy to use and primarily handheld, though fixed installations are possible. A calibrator is valued by technicians due to its high level of accuracy and its universal range of applications.
-
Product
Ultrasonic Level Transmitter
USonic-R
-
The Drexelbrook family of ultrasonic technology products offers a line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.The USonic-R multifunctional level measurement system can be used for a wide range of applications ranging from simple indication of level to more demanding two channel inputs such as differential level and submerged flow.This ultrasonic level transmitter is easy to use. Simply set the measurement range directly in inches, feet, millimeters, centimeters or meters via the menu driven display.
-
Product
Sample Conditioning Communications Interface
Pilot Pro Series
-
Parker's Pilot Pro™ package has been designed with a high level of flexibility to accommodate multiple configurations of local area communications networks.
-
Product
CANbus Controller for VMEbus
VME360
-
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
Product
High Speed Logic and Data Path Management
-
The ADI Data Path Management portfolio offers Data Path Signal Conditioners, Digital Crosspoint Switches, Level Translators, Serializer/Deserializer & Selector Muxes and Track/Hold Amplifiers for meeting the tight requirements of modern high data rate system. ADI's system solution focused products are easy to integrate to any signal chain with single supply usage while achieving low jitter, high output swing, fast rise/fall time.
-
Product
Signal Analysis
Cross-Spectrum FFT Analysis
-
The program Cross narrow-band spectrum is used for evaluation of the interrelation between the signals’ parameters obtained from the two primary transducers installed at various parts of the controlled object. This program can be used for detection of noise source location, for sound absorption level evaluation and the researched object acoustic properties control, for evaluation of space-time distribution of the directional energy flux (Poynting vector), for the ground cross-section FR characteristic evaluation (Nakamura method), etc.
-
Product
Sound Level Meter
831-LOWN
-
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
