Level
high or low along a bead it's a measure referenced.
See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
Fixed Attenuator
FAXE
-
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
Product
Professional Geological Compass
COCLA
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*Declination (± 30°) and inclination adjustable*Automatic arresting of needle when not in use*Eddy current damping allows reading after approx. 3 sec.*Transparent circle with diameter 50mm with interval of graduation 1°*Dip measurement range 270° graduated in 5°Reading by estimation 1°*Deep etched tracing edge graduated (60mm)*Circular spirit level (observable also from underneath)
-
Product
PXI 8 Slot BRIC 120x16 2-pole (8 sub-cards)
40-561A-122-120X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
2U 19” Edge Server with Intel® Xeon® Scalable Silver/Gold Processors for 5G MEC Infrastructure Deployment
MECS-7211
MEC Server
The MECS-7211 Edge Server focuses on the edge of 5G networks to provide an open, white box platform for 5G Open RAN, private 5G networks, and a wide range of 5G MEC applications including smart cities, retail, manufacturing, autonomous vehicles, Argument Reality(AR), virtual reality(VR) and healthcare. The MECS-7211 is designed to meet stringent requirements by delivering a high level of deployment flexibility, reliability, scalability, and carrier-grade processing performance further augmented by hardware expansion. With a 450mm system depth in a small footprint 2U chassis, all I/O front access, wide operating temperature support (-5°C to +55°C), and PCIe expansion slots reserved for access to acceleration hardware such as GPU, FGPA and QAT adapters, ADLINK’s MECS-7211 is a high performance COTS platform that meets varying application and deployment requirements, and enables customers to focus on differentiating their end solutions.
-
Product
System to Handle Wafer Levels
AMI AW Series
-
Operator-Free Wafer Inspection, Analysis and Sorting The AW Series are advanced high-capacity, high throughput automated wafer C-SAM® instruments specialized to deliver maximum sensitivity for the evaluation of wafer and device level applications.
-
Product
Dual 4 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-761-002
Multiplexer Module
This terminated dual 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Safety Certified I/O Modules
HY-TTC 48XS
-
HY-TTC 48XS is an intelligent safety I/O module for extending the number of I/Os in mobile applications. The I/O module acts as a slave and is used in combination with, and controlled by a master electronic control unit and communicates via the standardized CANopen protocol, parameterized according to CiA DS 401. It is also compliant to the European Standard EN 50325-5 for CANopenSafety and is developed in accordance with the international standard EN ISO 13849 on functional safety, performance level (PL) d.
-
Product
Water Detection Sensor
EZ-10
-
Panasonic Industrial Devices Sales Company of America
The EX-10 is a special Thru-Beam Sensor that was designed for two purposes; to check fluid levels and to detect the level of liquids containing water. The emitter on the EX-10 Sensor uses a particularly strong IR beam to not only penetrate transparent, but also semitransparent or colored containers such as PFA packages or shampoo bottles. Also, the sensitivity of the Sensor is adjustable to allow it to focus on a target, such as distinguishing foam from liquid in drinks, as an example.
-
Product
Quad 4 to 1 50 600MHz PXI RF Multiplexer
40-760-004
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Electrical Fast Transient Pulse Group Generator
SKS-0404IB
-
Shanghai Sanki Electronic Industries Co., Ltd.
Electrical fast transient pulse group generator SKS-0404IB fully complies with the new standards of IEC61000-4-4, EN61000-4-4 and GB/T17626.4; provides pulse test voltage up to 4500V, which can meet various product standards Severity level ; pulse frequency up to 1MHz, and continuously adjustable; imported discharge switch, high precision, long life, good reproducibility; using 7-inch true color touch screen control, convenient for users to directly program and control.
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Bus Analyzer / Exerciser
VME850P2
-
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
Chromatic Dispersion Emulator
CS-CDE
-
The ClearSpectrum™-CDE is a chromatic dispersion emulator suited for test and measurement. This 1U half 19-inch rack-mountable module is designed to emulate tens of thousands of picoseconds per nanometer in a compact unit while maintaining very low insertion loss. It is a passive, ready-to-use emulator which can be cascaded several times to achieve higher levels of dispersion.
-
Product
High-density Power Drivers
-
Gate drivers, FETs and protection circuitry integrated into a single package to drive loads in industrial and home-appliance applications, with increased power density per cm². ST’s high-density power drivers are System in Package (SiP) solutions integrating in compact QFN packages the STDRIVE gate drivers and MOSFET-based power stages, responding to the industrial market trend towards higher levels of integration and lower development costs.
-
Product
Multi-standard Satellite Modulator For PCIe
DTA-2107
-
DekTec's satellite modulator for DVB-S, DVB-S2 and ISDB-S, with symbol rates up to 55MBd. The output level is programmable up to -10dBm (DVB-S).
-
Product
Water Level Controller with Timer & Overflow Sensors
IM1730
-
Ajinkya Electronic Systems provides water level controller which is most popular in housing societies. Water is a precious natural resource and it’s our social responsibility to save water whenever and wherever possible. In cities we get treated water and which makes it more precious. So there is a need to use this resource judiciously and carefully. In societies there are overhead tanks which gets filled periodically from the underground tank. The prosess requires man power for timely switching off the pump to avoid dry running as well as overflow of the water. The water level controller for societies offers a smart solution for pumping of the water to overhead tanks in buildings
-
Product
Automated Optical Inspection System
AV880 Series
-
The AV880 Series of AOI solutions from ASC International provides the same high level inspection capabilities as found in our AV862/AV871 Series of AOI systems all wrapped into an inline platform for continuous flow requirements. A price to performance ratio sure to please those looking for a quick ROI.
-
Product
Tantalum-Polymer
POSCAP™
-
Panasonic Industrial Devices Sales Company of America
Panasonic POSCAP™ Solid Electrolyte Chip Capacitors offer stable capacitance at high frequency and temperature, with low-ESR/ESL. These Capacitors utilize a sintered tantalum anode with a proprietary high-conductivity polymer cathode. Panasonic's innovative construction and processing yields one of the lowest ESR levels in Tantalum-Polymer Capacitor technology, while exhibiting excellent performance in high frequency applications. POSCAP Capacitors are available in various, compact package sizes for a small PCB footprint while offering high volumetric efficiency for capacitance. In addition, Panasonic’s POSCAP parts demonstrate high reliability and high heat resistance, making them the ideal Chip Capacitor for digital, high-frequency devices and more.
-
Product
Automated Shock Test Systems
AutoShock-II Test System
-
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
Product
SparkFun Environmental Combo Breakout
CCS811/BME280 (Qwiic)
-
The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 and BME280 ICs. This unique breakout provides a variety of environmental data, including barometric pressure, humidity, temperature, TVOCs and equivalent CO2 (or eCO2) levels. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
PXIe-6571, 1-Slot, 100 MVector/s PXI Digital Pattern Instrument
786320-01
Digital Pattern
1-Slot, 100 MVector/s PXI Digital Pattern Instrument - The PXIe‑6571 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. It also includes debugging tools … like Shmoo, digital scope, and viewers for history RAM, pin states, and system status. The PXIe-6571 requires a chassis with 82 W slot cooling capacity, such as the PXIe-1095.
-
Product
Quad 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-004
Multiplexer Module
The 40-761A-004 terminated quad 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Accelerometer
AP2038
-
Combination of high axial sensibility, intrinsic frequency, and shock resistance; Low sensitivity to electromagnetic fields; Feed voltage and current wide range; Low intrinsic noise level.
-
Product
Temperature/Process Controller
2600
-
Series 2600 Temperature/Process Controllers set a new standard for quality, versatility, ease-of-use and value. While they include a high level of standard features, many function setup items appear in the control menu only when the function is selected, so you don?t have to wade through unnecessary items.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
Spectrum Analyzers
DSA700 Series
-
Entry level spectrum analyzers for education, IoT, hobby, and radio applications 500 MHz and 1 GHz models with option for Seamless Signal Capture, EMI, and more
-
Product
Engineer to Print
-
ARC has a build-to-print manufacturing capability with our unique ‘engineer-to-print’ philosophy to make sure precision manufacturing and final build accuracy is top priority for your module level or system level builds. We have a thorough process and because we have our own products and test solutions running through our production operation, we know the importance of having a regimented manufacturing process, augmented with engineering expertise to address challenges that come up with building complex, high-mix, medium volume products.
-
Product
RFID-Coded and Magnetically Coded Safety Sensors
-
- Actuation possible from different directions- Meets the interface description CB24I from ZVEI- Can be connected in series- Conceal behind stainless steel for enhanced tamper prevention- Meets highest safety levels to ISO 13849-1 and SILCL 3 to IEC 62061
