Platinum Resistance Temperature Detectors
offer precision; accurate, repeatable, stable and linear thermometry.
See Also: Platinum
-
Product
Fixed Gas Detectors
-
Teledyne Gas & Flame Detection
Are you looking for reliable and efficient fixed gas detectors? Discover our detection devices especially designed for professionals in the industry and in the service sector.
-
Product
Temperature, Velocity & Pressure Measurement
ATVS-NxT
-
Advanced Thermal Solutions, Inc.
The ATVS-NxTTM hot wire anemometer is a fully-portable scanner that provides rapid and highly precise of temperature and air velocity measurements for thermally characterizing electronic packages.
-
Product
Phase Detectors
-
Holzworth Instrumentation, Inc.
These components are targeted for use in phase noise measurement systems and ultra low phase noise phase lock loop designs.
-
Product
Automatic Oil Tan Delta & Resistivity Kit
MOTR
-
The Motwane Manufacturing Company
Motwane's MOTR is multifunctional automatic test kit designed for accurate measurement of the Dielectric Constant, TanDelta, Resistivity & capacitance of transformer oil & other electrical insulating liquids. It has preprogrammed test sequences as per various International standards along with customized test sequences as per user requirements. Internal memory for 250 tests provided with PC interface & report generation facility. Inbuilt thermal printer for onsite results. Test cell is designed as per IEC247 with calibrator for onsite calibration of kit.
-
Product
USB Smart Detector
OL 731
-
The OL 731 USB Smart Detector is a low-cost, hand-held radiometer/photometer that can be tailored to the spectral response of the user's specific application requirements with the use of a range of sensors and filters. Several units can be multiplexed on to one USB, and it can be programmed to read in any user-specified radiometric or photometric unit. The OL 731 is suitable for a variety of critical applications.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Oven Temperature Profile
-
Temperature profiling provides an effective method for measuring the actual environmental and product temperature during the cure process - essential for ensuring quality finish and a successful cure of a powder coating.
-
-
Product
Pulse Holiday Detector
NOVOTEST SPARK-1
-
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
-
Product
Torque Meter for TQ-3507 High-Stiffness Torque Detector
TQ-5300
-
TQ-5300 Torque meter, used with the TQ-2000 series High-stiffness torque detector, can convert the pulse output of the detector to digital torque value and analog voltage output.
-
Product
Infrared CO2 Gas Detector
SMC 5100-88-IT
-
The SMC 5100-88-IT detector monitors Carbon Dioxide, a toxic gas that can be dangerous in enclosed areas. The sensor monitors for indoor air quality to ensure a healthy, comfortable, and productive work environment.
-
Product
Earth Resistance Tester
-
PeakTech Prüf- und Messtechnik GmbH
A Rugged sealed digital earth tester is built with all the protection you need for outdoor use. The instrument is suitable for the testing of single earth electrodes such as lightning conductors and other small earthing systems according to VDE 0413. The resistance of conductors such as continuity and conduit coupling joints can also be measured. Two-terminal operation measurement, which reduces the accuracy, can also be done by shorting P and C terminals. It has an advanced circuit design that permits the instrument to operate with the minimum influence from earth voltage and earth resistance of the auxiliary spikes.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Live Line Clamp Insulation Resistance Tester
MLIT-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy and convenient live line insulation measurements for servo motor,inverter motor and power line.・More than 0.1MΩ for power line.・More than 10MΩ for servo motor and equipment.
-
Product
Temperature Probe for Outdoor
TP32MT…
-
Series of Pt100 1/3 DIN 4-wire or T-type thermocouple temperature probes for outdoor/environmental measurements.
-
Product
Expert Partial Discharge Detector
XDP-II™
-
The well-established XDP-II™ is a battery-operated portable device allowing partial discharge detection and analysis. The data is saved in its internal memory for local or further analysis on the PC-based XDP-SOFT™. Paired with the proper accessories, the XDP-II™ becomes a powerful solution for many applications such as Cable Joints and Elbows, Switchgear, Offline, Acoustic, TEV, Rotating machines, Transformer, etc…
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
Multiplex Temperature Tester
TMP-8/TMP-16
-
• 8 channels temperature signal (TMP-8) or 16 channels temperature signal (TMP-16) • T type or K type thermocouple • Temperature range: -40 ~ 300°C. Testing accuracy: 0.5% • Channel sequence is displayed by 2 LED and temperature is displayed by 4 LED • Freely set up the software with PC and record the change of temperature and select the channel.
-
Product
Flange-Type High Stiffness Torque Detector
TQ-3507
-
The improvement of energy efficiency has been required in future generation vehicles. The TQ-3507 Torque Detector developed for the measurement of torque capacity 5 kNm accurately captures minute torque fluctuations. It helps to grasp the energy loss precisely and improve energy efficiency of your system.
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Battery Resistance Tester
FBR-6100NT
-
Fuzhou Fuguang Electronics Co., Ltd.
FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.
-
Product
Intrinsically Safe Temperature Module
ATMi
-
AMETEK Sensors, Test & Calibration
The ATMi intrinsically safe portable temperature modules offer the functionality and flexibility to read up to two temperature inputs with a single HPC50 handheld pressure calibrator. Use the modules to add temperature measurement to the HPC50 series calibrator. The ATMi intrinsically safe temperature modules deliver the same high level accuracy whether in the lab or in the field.
-
Product
Metal-sheet Double-feed Detector
GD
-
Panasonic Industrial Devices Sales Company of America
The GD Double-Feed Detector allows for the detection of various metallic sheets. Panasonic offers three (3) types of heads: Small Object, High Precision or Long Sensing Range. Some applications are detecting overlay of washers, detecting missing tablet package in a box and detecting seam of hoop material.
-
Product
Transformer Winding Resistance Meters
RMO TT Series
-
The Tap Changer Analyzer & Winding Ohmmeter of the RMO-TT series is designed for winding resistance measurement of inductive objects, and for a tap changer analysis. The RMO-TT series is based on the state of the art technology, using the most advanced switch mode technology available today. The RMO-TT instruments are accurate (0,1%), powerful (up to 100 A) and still portable. The Instruments generate a true DC ripple free current with automatically regulated measurement and discharging circuit. RMO-TT instruments can perform a simple, quick and reliable transformer on-load tap changer condition assessment. This series of instruments enable measurements of a winding resistance in every tap position, current ripple values (percentage of a current drop during a tap change) and transition times during the tap changes. Problems with a connection, contacts, and selector/diverter switch operation (tap change with interruption) can be detected with these measurements.
-
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
Product
Ambient Temperature CalPod Module, 20 GHz
85530B
-
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button and without removing the DUT or re-connecting standards.
-
Product
Winding Resistance Meter 15Amps, 2 Channels
WR14
-
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
Product
Insulation Resistance Measurement
MD 15KVR
-
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
