Product

4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V

CPCI-7500

-

TEAM SOLUTIONS, INC.

CPCI-7500 - TEAM SOLUTIONS, INC.

*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS

Product

MIL-STD-1553 Fiber Optic Bus Extender

FO-1553

-

Avionics Interface Technologies

FO-1553 - Avionics Interface Technologies

Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT

Product

PXI Express High Speed Optical FPGA Board

HSS-8324-DSP

-

Conduant Corporation

HSS-8324-DSP - Conduant Corporation

The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.

Product

Aerial Fiber Optic Cable

-

AFL

AFL

AFL offers a complete portfolio of fiber optic cable, supporting hardware and compression accessories that are designed to meet the most demanding transmission and distribution environments. As the leading world manufacturer of fiber optic cable, AFL is uniquely positioned to provide a full line of all-dielectric self-supporting (ADSS) aerial cables and Optical Ground Wire (OPGW) as well as supporting hardware and accessories.

Product

Optics Test Equipment

Software For Autocollimators And Test Telescopes

-

Optik Elektronik Gerätetechnik GmbH

Software For Autocollimators And Test Telescopes - Optik Elektronik Gerätetechnik GmbH

Small investment - big improvement in measurement accuracy! The CROSSDETECT software is used to retrofit existing autocollimators of all types that are already equipped or can be equipped with a camera. The use of camera and software ensures that the measurement accuracy is increased by a factor of approx. 10 compared to visual measurements! The software can also be supplied complete with an autocollimator.

Product

Optical Light Sources

-

Wuhan Sunma Technology Co., Ltd.

Wuhan Sunma Technology Co., Ltd.

Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.

Product

Optically Isolated Measurement System

IsoVu

-

Tektronix, Inc.

IsoVu - Tektronix, Inc.

IsoVu offers complete galvanic isolation and is the industry’s first measurement solution capable of accurately resolving high bandwidth, low voltage differential signals in the presence of large common mode voltages. The stand out feature of IsoVu™ is its best in class common mode rejection across the entire bandwidth. Accurate differential measurements rely on a measurement system’s bandwidth, rise time, common mode voltage, common mode rejection capability, and the ability to connect to smaller test points to characterize devices that are shrinking in size and increasing in performance. Despite these requirements, advancements in test and measurement for power testing, EMI testing, ESD testing, and remote measurement capability have been minimal at best and have not kept pace with changing requirements. While differential voltage probes have had modest performance gains in regard to bandwidth, these probes have failed to make any substantial improvements in regard to common mode rejection, and connectivity. IsoVu is a leap forward in technology and is the only solution with the required combination of high bandwidth, high common mode voltage, and high common mode rejection to enable these differential measurements.

Product

SOSA Aligned LVDS with Optical I/O Kintex UltraScale FPGA - XMC

Model 71813

-

Mercury

Model 71813 - Mercury

- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Supports the emerging SOSA™ Technical Standard- PCI Express (Gen. 1, 2 & 3) interface up to x8VITA 42.0 XMC compatible with switched fabric interfaces- Optional front panel optical interface- Ruggedized and conduction-cooled versions available- Please refer to the product datasheet for Installed FPGA IP Module details

Product

High-Definition Distributed Fiber Optic Sensing

ODiSI

-

Luna Innovations Inc.

ODiSI - Luna Innovations Inc.

Luna’s ODiSI system provides the world’s highest resolution distributed fiber optic sensing solution for strain and temperature measurement. Using low-profile optical fiber as sensors, the ODiSI system maps strain and temperature fields with sub-millimeter spatial resolution, providing unprecedented detail and data insight.

Product

Optical Sensor

-

Sendot Research bv

Sendot Research bv

Sendot develops and produces optical sensors that measure with light. Our optics are unique, our intelligent electronics direct the measurements and convert them into measurement results.

Product

Optical Performance Monitor

-

Optoplex Corporation

Optoplex Corporation

Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.

Product

Optical Fiber 4×1 Switch

OFSW - 4 × 1

-

Hangzhou Huatai Optic Tech. Co., Ltd.

OFSW - 4 × 1 - Hangzhou Huatai Optic Tech. Co., Ltd.

OFSW-4×1 is a 4×1 prism optical switch. It can support 4 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.

Product

Highly Integrated Optical Inspection

BOA

-

Teledyne DALSA

BOA - Teledyne DALSA

BOA is a highly integrated optical inspection tool for controlling quality and increasing productivity. It comprises all the elements of an industrial machine vision system in a tiny smart camera style package.

Product

X4 Optical Fiber Fusion Splicer

-

Radiantech, Inc.

Radiantech, Inc.

Smart-connected APP, Splicing record management, Intelligent burglary-resisting system 1 sec. topspeed boot time, 6 sec. splicing time, 12 secs. Heating time. 3D protection cover reduce risk and unpredictability Handy, lightweight, anti-dropping solid and durable. Hi-Speed USB connection internet remote control.

Product

Optical Profilometers

-

KLA-Tencor Corp

KLA-Tencor Corp

Profilm3D® and Zeta™ optical profilometers provide fast, easy, non-contact solutions for 3D surface topography measurements. Our portfolio of optical profilers supports a variety of measurement techniques, including white light interferometry, True Color imaging and ZDot™ confocal grid structured illumination. KLA Instruments can help guide you to the right optical profiler solution for your unique needs.

Product

Managed Ethernet Switch with L2/L3 Layer Support and Fiber Optic Option

ES2

-

North Atlantic Industries

ES2 - North Atlantic Industries

Ethernet Switch module, ES2 provides up to 16 10/100/1000 Base-T 1 Gb ethernet ports. Additionally, there is one 10/100/1000 Base-T maintenance port interface, one RS-232 maintenance/console port interface, and a Fiber-Optic channel with four 10 Gb ports. It also provides numerous L2 and L3 networking, quality of service (QoS) and security features available as described below.

Product

1310nm Direct Modulated Optical Transmitter

ONT-8600AR

-

Hangzhou Huatai Optic Tech. Co., Ltd.

ONT-8600AR - Hangzhou Huatai Optic Tech. Co., Ltd.

Huatai 1310nm direct modulation optical transmitter, adopts high linearity DFB laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser APC, ATC closed loop control circuit. All the operating parameters are controlled by microprocessor, and the LCD screen on the front panel can display relative operating status and the fault information. ONT-8600AR has all the technical characteristic and function of ONT-8600AS. For its rainproof structure, it can be installed outside and its power supply is 220VAC or 60VAC optional.

Product

Fibre Optic Converters

-

Pontis EMC

Pontis EMC

In complex testing environments it is often needed that electrical signals have to be transmitted into the chamber or out of the chamber to the test equipment.For that purpose we offer a variety of different interfaces that convert electrical signals into optical signals and back. Such the signal can be transported via fibre optics and is immune against electrical fields.

Product

High Static Stiffness Optical Breadboards

5700 Series

-

Kinetic Systems, Inc.

5700 Series - Kinetic Systems, Inc.

They feature a lightweight precision formed steel honeycomb construction with 3/16″ ferromagnetic stainless steel top skin and 3/16″ low carbon steel bottom skin with a black polyurethane finish.

Product

Fiber Optic Sensor & Amplifier

FG-1300 | FS-5500/FS-540

-

Ono Sokki

FG-1300 | FS-5500/FS-540 - Ono Sokki

The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.

Product

Automated Optical Inspection Solutions

-

Chroma ATE Inc.

Chroma ATE Inc.

Adjustable criteria for different process application or modelFlexible algorithms programming editor for mono-crystalline and multi-crystalline silicon solar cellsMultiple interface to communicate with manufacturing equipment or information systemVarious defects inspection capability from multilayer LED lighting designFlexible design that can be easily integrated to your in-line printing system and sorting system

Product

3D Automated Optical Inspection System

EAGLE 3D 8800 SERIES

-

Pemtron Co., Ltd

EAGLE 3D 8800 SERIES - Pemtron Co., Ltd

EAGELE 3D 8800 AOI applies 8-way projection for 3Dmeasurements to all models, minimizing shadow effectserrors and performing 100% 2D&3D examinations simultaneouslyin all FOV areas.

Product

Optical Inspection

-

Gardien S.C.A.

Gardien S.C.A.

Typically, in a standard PCB manufacturing facility, there will be a department where people perform inspection of PCBs through a manual processes, such as visual inspection with magnifiers, microscopes, etc...