Electrical Testers
-
Product
Roughness Tester
-
Compatible with four standards of site to measure surface roughness ofvarious machinery-processed parts, calculate corresponding and clearly display allmeasurement parameters. When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
Product
Respirator Fit Tester
PortaCount
-
The PortaCount® Respirator Fit Tester features intelligent touchscreen solutions, providing assistance across your entire respiratory protection program from training through compliance. FitCheck™ mode allows you to quickly identify the right mask and provide staff with a better understanding of how a respirator fits. Video animations guide staff through the proper movements for each exercise, better identifying poorly fitting masks.
-
Product
Motor Tester and Analyzer
ITIG
-
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
Product
Single Sheet Tester
Model SST500X500
-
Gopal Make single sheet tester SST is developed as per IEC 60404-3. It can be attached as probe to Ep400 Main unit and user can test specific total loss, specific apparent power, and r.m.s value of magnetic field strength as well as B/h curve in the software.
-
Product
ProxiLAB Quest Contactless Tester
-
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
Product
Service Testers
-
Service tester with receiver probe, laser pyrometer, alligator clip cable, 10 inch handle, manual and standard bag.
-
Product
Core Loss Testers
S30 and S30S Series
-
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
Product
Exhaust Back Pressure Tester
33600
-
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
Product
Suspension/Road Contact Tester
VLT3673-G6
-
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
Product
Solder Wettability Tester
5200 Advanced
-
This is an ultra-high-sensitivity wettability tester developed to evaluate the solder wettability of ever-miniaturizing electronic components. Electronic devices, especially mobile devices, are becoming more compact and multi-functional. As the number of electronic components mounted on them increases and the pitch of connectors that connect each device increases, soldering parts are becoming increasingly miniaturized. expected to respond to further miniaturization of electronic components and miniaturization of joints in the future .
-
-
Product
EL & VI Tester
REOO RO-EV2400A
-
REOO RO-EV2400A EL & VI Tester is designed for PV module manufacturing lines, enabling fast EL and VI inspection for hidden defects and electrical quality verification.
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Product
Oil Breakdown Voltage Tester
DTA 100 C
-
Insulating oil testing with the BAUR DTA 100 C. The BAUR DTA 100 C oil tester is designed for continuous operation in the laboratory and is characterised by the combination of extraordinary features. As a high-performance device with a test voltage up to 100 kV, with clear breakdown detection and absolutely reliable measurement results even across several measurement sequences, the BAUR DTA 100 C is the leading testing device for users in the electricity and other industries and in testing institutes.
-
Product
Adhesion Testers
-
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
Product
Microhardness Testers
-
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a range of microhardness testing solutions including the cost-effective MT91 and MS-ZH microhardness testing system.
-
Product
Elasticity, Bend & Impact Testers
-
The performance of coatings when influenced by external stresses caused by stretching, bending or impact, determines their suitability for their designed application. A coating designed for use in the coil coating industry, for example, should have the ability to stretch as the substrate is formed into its desired shape without damage.
-
Product
IPTV Tester
NetProbe 2000 IPTV Analyzer
-
The NetProbe 2000 IPTV is a handheld IPTV tester that can emulate a set top box or passively monitor video channels in pass-thru mode. It can be used to turn up new service by auto scanning all channels and checking their quality or to troubleshoot the service. It is battery powered and easy to operate by a tier one technician.
-
Product
Flying Probe Tester Substrate
-
Substrates with structures down to 10µm and several hundred thousand test points per panel require specific solutions forscanningcapacitance measurementhigh accuracy and temperature Management
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
Wide-Range Digital Igniter Tester
4314Mi
-
Featuring the intrinsically-safe internal circuitry of our storied 4314 igniter tester line, the 4314Mi is the newest addition to Valhalla Scientific's i-Series Wide Range Igniter Testers.
-
Product
Brake Hydraulic Pressure and Electric Parking Brake Systems Test Bench
Model BHP/EPB™
-
The new Model BHP/EPB™ Brake Hydraulic Pressure (BHP) and Electric Parking Brake (EPB) Systems test bench from MB Dynamics accurately measures and controls the hydraulic pressure and EPB power levels applied to brake calipers during automotive buzz, squeak and rattle (BSR) testing, as well as brake durability, stability, functional or performance testing. Varied brake pressures are applied according to timing diagrams, as well as automated or manually program-controlled repeat cycles, as required to assess brake caliper/rotor assembly noise, useful service life, and other critical performance metrics.
-
Product
Pocket Dissolved Oxygen Tester
LD-LPKDO-A10
-
Pocket Dissolved oxygen tester LD-LPKDO-A10 is equipped with polarographic sensor to measure dissolved oxygen content. The system menu of dissolved oxygen meter can set 6 parameters which includes the number of calibration points, temperature units etc. It can measure the dissolved oxygen content present in water, waste water, other liquids & solutions.
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
Product
Network Tester
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
Product
In-Circuit Testers
-
Whether you’re choosing from our stand-alone manually loaded ICT tester all the way to our fully automatic In-line test system, Acculogic has the solution for you!Acculogic’s Scorpion family of automated test equipment and in-circuit fixture-based testers were created with one underlining theme in mind: “Cost-effective Testing”.
-
-
Product
Ball Pressure Tester
4710
-
The ball pressure tester is used to test the thermal properties of insulating materials. The test sample is placed in an oven and a steel ball is pressed against the surface. The impression of the steel ball is measured to see if it meets the requirements.
-
Product
Heat Seal Tester
HST-01A
-
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
Product
Electromagnetic Radiation Tester
KM 196
-
Kusam Electrical Industries Limited
Unit : Electric Field : V/m; Magnetic Field : mT. Precision : Electric Field : 1V/m; Magnetic Field : 0.01 mT. Range : Electric Field : 1V/m ~ 1999V/m. Magnetic Field : 0.01 mT ~ 19.99 mT. Alarm Threshold : Electric Field : 40V/m, Magnetic Field : 0.4 mT. Reading Display : 3½ Digit Digital LCD display with Backlight. Frequency Range : 5Hz ~ 3500MHZ. Sampling Time : About 0.4 second. Measuring Mode : Dual Mode. Overload Alert : “1” appears on LCD. Sound & Light Alarm. Data Hold function. Auto Power Off. Average & Peak measurement. Low Battery Indication. Operating Temperature & Humidity : 0°C ~ 50°C; below 80%RH. Power battery : 9V Battery. Dimension : 63.6 x 31 x 125.8mm. Weight : Approx. 146g.
