Electrical Testers
-
product
Load Cell Tester
LCT-Ultimate
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
product
Network Cable Tester
PHCT45
This Pyle network cable tester checks RJ45 and BNC network cables for continuity and correct polarity. LEDs show the status of each pin. , perfect for the IT guy on the go.
-
product
Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.
-
-
product
LDE Electrical Analyzer
The Cadence LDE Electrical Analyzer helps designers identify, analyze, and minimize the effect of parametric issues associated with manufacturing variability to improve design performance.
-
product
Transformer Testers
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
product
Electric Multipliers
EFC
The easy-to-operate EFCip electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines and rigs, the Mountz torque multipliers achieve precision torque in a quick, cost-efficient manner.
-
product
Digital Insulation Tester
DIT-1020
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT-1020 is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage of 100 Volts DC, its short circuit current is less than 500uA.
-
product
Heat Seal Tester
HST-01A
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
product
Ball Rebound Tester
Hildebrand Prüf- und Meßtechnik GmbH
The ball rebound tester is used to determine the resilience of foam materials in accordance with DIN EN ISO 8307 and ASTM D 3574.
-
product
Hipot Testers
Hypot® Series
The Hypot Series sets the standard for safety and efficiency in production line Hipot Testing. Whether your application requires AC Withstand tests, DC Withstand tests, or Insulation Resistance tests, The Hypot Series provides innovations that will allow you to begin achieving best practices for safety and efficiency without the need for an expensive automated test system or connection to a PC. You can even connect the Hypot Series with the HYAMP Series to form a seamless safety compliance system for Hipot and Ground Bond Testing.
-
product
Digital Phosphate Tester
MW12
The Milwaukee MW12 Phosphate Photometer lets you go digital with your testing. No more hit and miss testing with strips. Great for aquariums, aquaculture & coral, labs, water treatment, classroom and more. This meter is also ideal for educators that want their students to learn the basics of water quality analysis to apply in the real world.
-
product
Radiation Testers
The Ranger is a small, handheld, digital survey meter which offers excellent sensitivity to low levels of alpha, beta, gamma, and x-rays. It has built in efficiencies for common isotopes to calculate activity in Bq and DPM. It has a backlit display and a count light and abeeper that sounds with each count detected. Other features include selectable alert levels, an adjustable timer, and an optional wipe test plate. Internal memory and the free Observer USB Software allow you to download your data, set computer alarms, and calibrate your instrument! The Bluetooth and Observer BLE enables saving, sharing,and automation of surveys and RadResponder compatibility
-
product
Loop/Line Impedance Testers
Shanghai Beha Electronics Co., Ltd.
*Built-in earth tester.*Built-in loop/psc tester. 0.03 - 2000Ω (software ctrl).*Built-in voltmeter.*Built-in wiring checker.*One push button smart control.
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
Portable Tester
ECAD System 2002
The ECAD System 2002 is a portable, ruggedized tester that can be used for troubleshooting and condition monitoring of installed circuits, cables and wiring harness. The ECAD tester is a combination of traditional electrical measurements, a database for storing test results, and data analysis software. This powerful combination allows a user to evaluate the condition of all circuit components in a logical and straightforward manner from one end of the circuit.
-
product
Battery Load Testers
DURST Motor & Electric Industries Pty Ltd.
DURST Battery Load Testers and Analyzers
-
product
Electrical Tomography Software
Res2dinv
This very popular software, developped by M.H.Loke, uses the method involving the Sasaki minimum squares inversion (1992) to produce a 2D sub-soil model starting from the data of apparent resistivity (up to 2000 electrodes). It is completely automatic and does not require that the user formulates a starting model. When using a state-of-art computer, the inversion of a single pseudosection will require only a few minutes.RES2DINV supports spreading types like Wenner, Schlumberger, Pole-Pole, Pole-Dipole, line Dipole, equatorial Dipole and other non-conventional spreading types.
-
-
product
AC Motor Tester
JK115
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical performance test of single-speed, multiple-speed single-phase induction motors.
-
product
HiPot Testers
Testwave LLC has been selling, renting and servicing Hipot Products for over eight years.
-
product
Alternator Tester
ALTALYZER Tester
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
product
Electrical Swivels
Electrical Swivels enable the rotation of data and/or power cables and are designed to be integrated into the swivel stacks of Floating Production Storage and Offloading (FPSO) applications. They can withstand the typically harsh environments of the oil and gas (O&G) industry and are installed on vessels and/or floating moored platforms.
-
product
Cobb Absorbency Tester
DRK110
Shandong Drick Instruments Co., Ltd.
DRK110 Cobb Absorbency Tester is used to test the absorbency of paper and cardboard according to related standards.
-
product
Electric Vehicle Test Solution
As the automotive industry advances power conversion and battery technologies, Chroma has been actively working to improve electric vehicle (EV) testing performance and cost by developing flexible automated power conversion test platforms and regenerative battery test systems. Chroma ATE is a world leading manufacturer of precision test and measurement instrumentation, automated test systems, intelligent manufacturing systems, and turnkey test and automation solutions. Chroma’s Automated Test Systems for Electric and Hybrid Electric Vehicles consist of standard test platforms that are combined into one expandable test system that can test most power components in an EV’s power system. Compared to specialized test equipment developed for a single EV model or application, Chroma’s systems provide greater flexibility.
-
product
Circuit Testers
Precision Mastech Enterprises Co.
AC Voltage Range: 125V AC, 50/60 Hz, 0.3WOverload voltage: CAT II 125VHumidity: <80% relative humidityOperating Temperature: 32 to 104 (0 to 40)Storage Temperature: 14 to 122 (-10 to 50)Altitude: ~6500 ft. (2000m); indoor use onlyDimension: 3.23*1.73*1.26 in. (82*42*32 mm)Weight: Approx. 1.5oz (42g)Safety rating: TL CAT II 125V RoHS
-
product
Peel Testers
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
product
Cable Testers
DMX ADAPTER
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
product
Personal Grounding Tester
PGT120
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
product
Three-Phase Relay Tester
PTE-300-V
The equipment compromises of three independent output channels than can be selected as voltage or current. This enables the unit to be used as a complete single-phase equipment (Voltage, Current, and phase angle between them), or with channels synchronized, as a three phase voltage or three phase current generator from a single phase mains input. The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability.
