Standard Test Interface Language
IC digital vector test representation standard.
-
Product
Standard 0.81 (23.00) - 4.50 (128.00) Battery Probe
CP-059-026
-
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.00Mechanical Life (no of cyles): 100,000Overall Length (mil): 221Overall Length (mm): 5.61
-
Product
Noise Test
-
Noise testing is conducted to determine if materials can withstand external noises generated by various sources. It also includes air-borne and structure-borne noise measurements.
-
Product
Test Solutions
AT/CX/CM Series
-
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
Product
Interface Module
MC
-
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
Product
Camera Testing
SWIR
-
CI systems' SWIR turn-key test stations simulates low light conditions to test special application cameras. An intuitive user friendly software carries out a variety of tests. The test stations are radiometrically calibrated to perform comprehensive SWIR tests.
-
Product
Environmental Control System Test Platform
-
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
Product
Ethernet Digital Interfaces
-
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
-
Product
Standard 1.10 (31.00) - 3.85 (109.00)General Purpose Probe
SPA-64-2
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3: 0,365″; Tip 8: 0,385″; Tip ,9,10: 0,363″
-
-
Product
Test Applications
-
We have a long and enviable reputation for supplying quality test applications to a wide range of industries covering many different technologies. Not only do we understand your test requirements, but we also try to make the software simple to use and support.
-
Product
Usability Testing
-
Using our proven testing usability methodology, we deliver a 360-degree view on a product's operability by analyzing, identifying and benchmarking the weak spots in core features of the application and suggesting opportunities for improvement.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Transformer Testing
-
The ART-3D series of Automatic Ratio Testers are precision instruments, designed to measure the turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076. Now featuring an enhanced test lead design, the ART-3D is the perfect instrument for real-life field usage. ART-3D series also has Anti Induction circuit which makes it suitable for system voltages upto 765KV.
-
Product
GPIB to LAN Printer Interface
Model 4872
-
* Adds a GPIB Interface to Ethernet Printers. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Secondary output copies instrument print file to a PC for later printing with our Data Logger program.* Automatically finds and links to most printers.* Built-in test page confirms 4872 to printer operation.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and LAN crossover cable.
-
Product
European Standard for Remote Reading of Measuring Devices
M-Bus
-
M-Bus (Meter-Bus) is a European standard for remote reading of measuring devices. M-Bus is predominantly used in buildings, for example in electricity meters, gas meters, water meters or other types of consumption meters. It is also used for various sensors and actuators.
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
MiniPCI Express System Timer (PCIe Interface)
SKU-032-06
-
This MiniPCIe Timer uses a PCIe interface for synchronization of IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
Compatibility Testing
-
An application is incomplete if it is not compatible with the user environment so that the user can operate it
-
Product
Standard Version
-
WISE-STACK 200 is Advantech's lightweight and highly available industrial-grade private cloud.
-
Product
Design-for-Test
-
As designs move to smaller and more complex process technologies, ensuring devices are thoroughly tested becomes a bigger challenge. Mentor Graphics provides whole-chip test solutions that can help improve test -- and, therefore, device -- quality as well as control, or even reduce, the cost of test.
-
Product
Standard 1.17 (33.20) - 4.50 (128.00) Battery Probe
CP-2SB-8
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 88Full Travel (mm): 2.25Recommended Travel (mil): 78.7Recommended Travel (mm): 2.00Overall Length (mil): 315Overall Length (mm): 8.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Hipot Tests
-
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
-
Product
Vibration Testing
-
Response Dynamics Vibration Engineering, Inc.
We most often characterize a problem first and work from known conditions, and stay in “the known” as we proceed by making sense of what we observe as we move forward. We test and analyze the change in dynamics we are trying to create in real-time, on site, and often make changes to our experimental test plan on the fly as we discover how a system is actually behaving. In doing so we often get meaningful results from which we can make sound engineering decisions in a short time frame. We don't just make measurements and spit out data. We help identify the problem and propose solutions.
-
Product
Diagnostic Testing
-
Response Dynamics Vibration Engineering, Inc.
Response Dynamics has made diagnostic testing our core focus for over 30 years. We do this detective work well because we have particular expertise in structural dynamics and how it relates to vibration and acoustic noise issues on a myriad of levels. We enjoy this work because it stays interesting and draws on multiple disciplines in engineering and science.
-
Product
GPIB General Purpose Interface Bus
-
The design of the GPIB control card is fully compatible with the IEEE 488.1 and IEEE 488.2 standards, using the PCI interface, supporting the Plug & Play specification, and supporting Windows 95/98/Me /NT4.0/ 2000 /XP/7 Operating system, driver function library includes Windows development software tools such as Visual C++, Borland C++ Builder, Labwindows, Visual Basic, Delphi and Labview. This GPIB-supported library provides an NI-like command control syntax format, which is convenient for users to develop and transfer applications smoothly. This interface card also provides a conversational window GPIB interface program, which is convenient for users to directly control the instrument without writing a program.
-
-
Product
Test Probes
-
Our innovative Test Probes are the upgrade version of Auto Multi Meter. It can perform multiple circuit system test such as power supply feed, voltage and resistance measurement, continuity test, ground test, polarity check and components activation.
-
Product
Test Receiver
NTR GNSS
-
Our primary objective is to provide a high performance and fully flexible test receiver for all types of GNSS systems. Thus, the NTR fully supports all existing navigation systems. The signal processing is fully flexible. The high performance correlation engine with up to 80 channels is implemented in a powerful set of FPGAs. Signal acquisition and tracking are realized on a high performance embedded ARM Cortex A8.Supporting up to 4 L-band frequencies in parallel, the NTR GNSS test receiver supports all current GNSS transmission frequencies. Due to its plug-in design, the RF front-end can easily be customized for special filtering and other frequencies.
