Total Dissolved Solids
Total Dissolved Solides of a solution.
-
Product
Panel-mount Type Dissolved Oxygen Meter (Four-Wire Transmission, Membrane Type)
HD-480
-
The HD-480 industrial dissolved oxygen meter takes sequential measurements of the concentration of dissolved oxygen, which is an indicator used in the management of activated sludge tanks in waste water processing, and the quality of the water in boilers, or rivers and waterways.As there is no need to exchange the membrane of the disposable sensor included, it is easy for anyone to use.
-
Product
UV Fluorescence Total Reduced Sulfur Analyzer
Model T102
-
The Model T102 TRS analyzer uses the proven UV fluorescence principle to measure Total Reduced Sulfur at levels commonly required for ambient air monitoring.The Model T102 uses a high temperature external converter set at 850°C to allow conversion of H2S, methyl mercaptan, dimethyldisulfide, and methyl-disulfide to SO2 at this temperature with efficiency greater than 98%. A switching option alternately measures TRS and SO2 while showing both readings concurrently on the front display.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T102 comes with NumaView ™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView ™ Software.
-
Product
10.50 (266.70) 24" Solid Panel
P-1024
-
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. Finish is textured unless otherwise specified.
-
Product
Total Stations
-
GeoMax total stations offer you an excellent price-to-performance ratio without compromising quality.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
PXI 8 Slot BRIC Solid State 96x8 1-Pole (3 sub-cards)
40-563A-121-96X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Solid State Multiplexer Module, Dual 3-Channel, 30 A, Hardware Interlock
40-667C-011-HI
-
The 40-667C-011-HI is a dual 3-channel 30A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
-
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI 8 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-121-128X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
2x8 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9165A
-
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
15.75 (400.05) 24" Solid Panel
P-1524
-
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. Finish is textured unless otherwise specified.
-
Product
PXI 4 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-021-64X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Solid State Multiplexer Module, Dual 3-Channel, 30 A
40-667C-011
-
The 40-667C-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A, Hardware Interlock
40-667C-012-HI
-
The 40-667C-012-HI is a single 6-channel 30A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Total Energy System
5000
-
The electric vehicle (EV) charging market is rapidly expanding, with more and more people switching to electric cars. As the demand for EV charging stations increases, so does the amount of energy that is being exchanged. This energy exchange market is already massive, with charging peaks reaching into the megawatts of energy. With this amount of energy comes a significant amount of revenue, which requires the most accurate billing possible. That’s where TESCO’s Catalog No. 5000 – Total Energy System comes in. The Catalog No. 5000 is a double duo system that enables the testing and accuracy verification of Electric Vehicle Service Equipment (EVSE) and Field Test Equipment for testing EVSE’s in the field. This system is a dual-purpose DC and AC System and includes both a 100A AC (ACT-100) Test System and a 200A DC Test System (DCT-200).
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
MIPI Total Display IP Solution
DSI
-
The Arasan MIPI Display Serial Interface (DSI) Controller IP provides both device and host functionality. Additionally, the DSI Controller provides a high-speed serial interface between an application processor and display and follows a rigorous verification methodology to ensure interoperability of our DSI digital controller with our D-PHY analog IP. Arasan’s DSI solutions are MIPI standards-compliant and are designed to accelerate integration, lower risk and accelerate time to market for developers of display applications. Arasan’s expertise is backed by our unique silicon proven design discipline and product development process that ensures fast silicon success with our analog and digital IP.
-
Product
Refrigerant Leak Detector w/ Solid Electrolyte Sensor
RLD15B
-
UEi Test & Measurement Instruments
The RLD15B Refrigerant Detector is designed and certified to meet the new tougher standards and detect the latest refrigerants. Equipped with a heated sensor to increase accuracy and reduce false alarms, the RLD15B displays approximate leak sizes with the digital leak size indicator to help pinpoint leak sources. Finally, the mechanical pump draws gas over the sensor faster providing a quick response in a variety of contaminated or windy environments.
-
Product
Solid State Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Solid State Relays including Through-Hole and SMD, High Capacity and Phototriac Coupler Solid State Relays. Triac output components for AC load applications. Advantages include long operational life, high frequency switching, no contact arcs, high contact reliability, and noiseless operation.
-
Product
Solid State NMR
-
Magnets for NMR experiments are required to have a high homogeneity, which can be maintained over a wide range of field. Experiments are performed at fixed frequency and the spectrum is obtained by sweeping the magnetic field. This requires the field to be stable in spatial homogeneity and change steadily and repeatedly over time.
-
Product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
43-182B-006
-
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI Versatile Multiplexer, Solid State, 350mA, 60V
40-681A-001
-
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
-
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Product
PXI Solid State Very High Density Matrix
40-500-001
-
A very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high currents and voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
43-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
Pocket Dissolved Oxygen Tester
LD-LPKDO-A10
-
Pocket Dissolved oxygen tester LD-LPKDO-A10 is equipped with polarographic sensor to measure dissolved oxygen content. The system menu of dissolved oxygen meter can set 6 parameters which includes the number of calibration points, temperature units etc. It can measure the dissolved oxygen content present in water, waste water, other liquids & solutions.
-
Product
Dissolved Oxygen
-
Dissolved oxygen (DO) is one of the most important indicators of water quality. It is essential for the survival of fish and other aquatic organisms and is used in hydroponics as well. When dissolved oxygen becomes too low, fish and other aquatic organisms cannot survive. Sper Scientific dissolved oxygen meters are made to accommodate the user with rugged, portable meters for use out in the field. All of our DO meters offer fast and accurate DO response times in wastewater, surface water and aquaculture applications. Three basic styles of DO meters are available for varying applications: Pens, Portable Meters, and Multi-parameter meters.
-
Product
PXI Solid State Multiplexer, Single 6-Channel, 30 Amp
40-667B-012
-
The 40-667B-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
IsoPods: Streaming Meters For Recording Temperature, PH, Conductivity And Dissolved Oxygen
-
eDAQ isoPods™ are portable streaming data recorders. These electrically-isolated meters can be used for recording data in situations where signal noise and crosstalk would otherwise be an issue.
-
Product
21.00 (533.40) 24" Solid Panel
P-2124
-
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. Finish is textured unless otherwise specified.
