Machine Model
-
Product
Leather Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
Test method uses clean ball placed within the material applications, steel ball itself of the impedance and total weight, must be in conformity with the provisions, on this condition detection material zigzag waterproof penetration index, using the latest inductive components and special design, test as long as materials applications in water infiltration immediately automatic stop counting or in setting time (test times) arrived, namely automatic stop and display the time or times.
-
Product
Electromechanical Testing Machines
-
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Automotive Transient Surge Simulator Model
ISS-7600 Series
-
Designed to meet and exceed the testing needs to ISO7637-2 (2004), NoiseKen ISS-7600 series Automotive Transient Surge Simulator System offers flexible and productive testing facilities.
-
Product
Customized Testing Machine
-
Jinan Scientific Test Technology Co. LTD.
Customized Testing Machine
-
Product
Post-Mould Inspection Machine
IV-P1000
-
The IV-P1000 is a post-mould inspection machine best known for being a fully automatic vision inspection station and for having a user-friendly GUI for operator and recipe setup. This machine is best used to inspect packages for surface defects on top and bottom.
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
Universal Testing Machines
-
Dongguan Kejian Instrument Co., Ltd.
Universal Testing Equipment is designed specially for the adhesive industry. Used to testing peeling strength with different methods. I
-
Product
Potable Coordinate Measuring Machines
Romer
-
A first in the world of portable measuring arms: The ROMER Absolute Arm features absolute encoders and is therefore the first measuring arm which does not require referencing before measurement. When the arm is turned on, it’s ready to go.Quality control, inspection, on-machine verification, reverse engineering, virtual assembly or 3D modelling. Wherever these needs arise, you will find the ROMER Absolute Arm. Much more than just a metrology tool, its value lies in its versatility.Portability, stability, light weight and high-performance laser scanners make the ROMER Absolute Arm an all-purpose 3D measurement, analysis and digitising tool that can be used by anyone, anywhere and with minimum training.Unlike many metrology devices, the ROMER Absolute Arm does not require warm-up time or initialization, thanks to a stable carbon fiber structure and industry leading Absolute encoders. Simply take the measuring arm to the part, switch it on and start measuring.
-
Product
Single Screw Electromechanical Universal Testing Machine
CMT Series
-
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
Product
Fanless Machine Vision Computers for Extreme Operating Conditions
Neousys SEMIL
-
Neousys SEMIL are fanless computers for extreme operating conditions.- Intel® Xeon® E or Core ™ i7 / i5 / i3 9th / 8th Generation- IP67 - protection against water and dust (SEMIL 1700)- Operating range -40 ° C to 70 ° C with fanless cooling system- Up to 8 ports 802.3at Gigabit PoE +- M12 connectors- MIL-STD-810G and EN 50155 certified
-
Product
High-speed 3D Solder Inspection Machine
YSi-SP
-
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
Product
Injector Clean, Maintenance & Test Machines
-
Shenzhen Zeus Information Technology Co., Ltd.
Shenzhen Zeus Info Tech Co., Ltd. Injector Clean, Maintenance & Test Machines
-
Product
2U MGX GPU Server, Up To 4x H200 NVL, H100 NVL Or L40s And 3x NIC And SmartNIC DPU For AI Training, Large Language Models (LLM).
SKY-622G4
-
High density NVIDIA MGX™ GPU system up to 4 x PCIe GPU with NVIDIA NVLink™ bridge support, 3x NICs and smartNICsProcessor: Dual Intel® Xeon 6 Processors, TDP up to 350WMemory: 32x DDR5 6400 MHz RDIMM,up to 4TB supports MCRDIMMStorage: 8x E1.S NVMe at frontPSU: 6000 Watt 3+1 power supply with 80+ platinum level certification
-
Product
Automatic Fiber Jacket Stripping Machine - FBT-3000
-
Shanghai Fibretool Technology Co.,Ltd.
The FBT-3000 automatic fiber peeling machine is a new type of optical cable end processing equipment, which is based on the eagerness of optical fiber connector manufacturers to improve production efficiency and reduce the skilled manual emergence of optical cable end processing equipment. In order to solve the problem that the skin layer of optical fiber is usually peeled manually with wire peeling pliers, and the artificial denudation is low in precision, low in working efficiency and low in product quality.
-
Product
Motorized Bending Testing Machine
GW-A Series
-
Jinan Testing Equipment IE Corporation
GW-A series motorized bending testing machines are special equipment for bending test on reinforce bar, steel bar, and pipe etc. The motorized bending testing machine can do bending test in both directions according to the standard requirement. The motorized bending tester conforms to standards including ASTM A615, ASTM A615M, ISO 7438, and ISO8491 (E) etc.
-
Product
On-site EL/PL Inspection Machine
“EPTiF”
-
"EPTiF (EL/PL Test in Field)" enables you to check invisible conditions of installed solar panels during daytime by EL and PL inspections, which are adopted by a number of solar panel manufacturers, without detaching solar panels. Irradiance-independent and steady results can be obtained. This is the first in the industry.
-
Product
Environmental Chamber/Stability Chamber - One Door Model
HC20
-
This is a Environmental test chamber/ Stability chamber/Laboratory incubator single door model capable of performing in wide temperature range(0°c to 70°c) with precise temperature control over the entire range.
-
Product
16 DI/O IP67 Machine Mount M12 PROFINET/Modbus IoT Ethernet Remote I/O
ADAM-250PN
-
16-ch configurable DIO and 2-port power/ethernet daisy chainIEC 61131-2 type 3 sink DI and fast response source DOSupport I/O and power diagnostic and DO safety value protection functionsPrintable marking label & LED indicator monitoring system/network/diagnostic/power statusEnables cabinet-free front and side wall & machine mountingCompatible with M12 Screw lock and Push-pull fast-lockingRugged IP67 design resists EMC, vibration, dust, oil, and humidity from harsh/outdoorBuilt in Sensor/Actuator/Encoder Power Supply from each I/O portSupports PROFINET and Modbus/TCP, with extensible design for MQTT integration
-
Product
Compression Testing Machine for Special Purposes
-
Jinan Testing Equipment IE Corporation
These compression testing machined are suitable for testing the compression strength of components or structural material such as concrete, steel, brick, rubber pad, etc. These compression testing machines feature large test space and double actions. Hand operate, analog dial or monitor. Hydraulic servo with computer control.
-
Product
Virtual Machine Solution
M22
-
The M22 Virtual Machine Solution frees up lab space, increases reliability, and optimizes large scale installation's efficiency. With one M22 you can replace 22 desktops in your laboratory. The M22 utilizes shared redundant drives to ensure data and system integrity. The hyper-fast internal bus integrates perfectly with Maccor's MIMS Server ensuring up-to-date data backups.
-
Product
DIP Header with Screw Machine Contacts
Series 625
-
DIP Headers with Screw Machine Contacts. Aries offers a full line of DIP headers, available with either screw machine or coined contacts in a variety of styles. Consult Data Sheet No. 12032 for coined contacts.
-
Product
Bump Test Machine
-
Labtone Test Equipment Co., LTD
Bump test systems for electrical products repeating impact testing during transportation
-
Product
Coordinate Measuring Machine
SF87
-
Entry-level CMM for the production environment. WENZEL’s SF87 has the attributes needed for a shop floor CMM and benefits from an optimum measuring volume of 800 x 700 x 700 mm , its cantilever style configuration providing a very efficient footprint relative to measuring range.
-
-
Product
Superior Electromechanical Universal Testing Machine
WDW-S Series
-
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, the electromechanical universal testing system for tension,compression, flexure testing is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW-S series superior materials testing systems adopt robust load frames, precise load weighting system, advanced measuring and control system, and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurate testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
Product
Software Module for Analyzing Measured Data to any CAD Model
Verisurf Analysis
-
Simplifies part inspection through the comparison of measured points, clouds, and meshes, to all CAD file formats. Check part characteristics such as position and profile quickly and easily using a variety of alignment, analysis, and reporting techniques.Analyze to CAD with imported data sets or directly from measured points, clouds, or meshes from 3D measuring devices including portable probing and scanning systems and both manual and CNC CMMs to analyze part tolerance compliance.
-
Product
Pendulum Shock Testing Machine
UDAR-1
-
Pendulum shock testing machine “UDAR-1” is intended for calibration and verification of measuring transducers (both analog and digital) by means of shock impact as well as for shock testing of various specimen.
-
Product
Machine Vision SBC With AMD® Ryzen™ Embedded V1807B And V1605B APU, DisplayPort, HDMI, 2 GbE LAN, 2 IEEE 802.3at PoE GbE LAN And Vision-specific I/O
MIRU130
-
*AMD® Ryzen™ Embedded V1807B and V1605B APU*2 DDR4 SO-DIMM for up to 16GB of memory*2 GbE LAN and 2 IEEE 802.3at PoE GbE LAN*2-CH camera trigger outputs*2-CH LED lighting control*1-CH incremental quadrature encoder input*4 isolated DIO
-
Product
No-metal Testing Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
It is widely used in the manufacture, test and research dept. of plastic pipe, fittings, and sheet.
