Dielectric
-
Product
Dielectric Insulation Analyzer
DIRANA
-
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
Product
Dielectric Cure Monitoring Software
CureView
-
CureView dielectric cure monitoring software is a complete control and analysis package for operating all Lambient Technologies products. Our easy-to-use CureView software provides the flexibility needed in research and development along with user-configured operation for QA/QC and manufacturing applications.
-
Product
Dielectric Assessment Kit
DAK
-
Schmid & Partner Engineering AG
The Dielectric Assessment Kit (DAK) is ideal for all applications where high-precision dielectric parameter measurements (permittivity, conductivity, loss tangent) are required, including applications in the electronic, chemical, food, and medical industries. The dielectric probes are designed for fast, precise, non-destructive, and user-friendly measurements of liquids, solids and semi-solids over the 10 MHz – 67 GHz frequency range.
-
Product
Shoe Dielectric Resistance Tester
UI-FT07
-
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
Product
Dry Dielectric RF Coaxial Loads
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Transformer Insulating Oil Dielectric Tester
CXYJ-501
-
Shenzhen Chuangxin Instruments Co., Ltd.
Insulating Oil Tester is designed according to of GB-86 and IEC60156 standards.
-
Product
Automatic Dielectric Constant Tan Delta And Resistivity
-
No Balancing and Calculation required to calculate Volume / Surface Resistivityand Dielectric Constant.Complies IEC 60250, IS 4487, Test jig Conform to ASTMD 257Built in Thermal PrinterSerial port RS232 for data downloading.Can be used to check liquid sample with Three Terminal oil cell.Storage 100 Test reports
-
Product
Microwave Dielectric Measurement Systems
-
This system enables fast and non-destructive measurements of materials having various shapes, including thin films. Enables fast and non-destructive measurement of permittivity of thin-films and various dielectric materials using the evanescent mode of an open coaxial resonator.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Broadband Dielectric Spectroscopy
-
Material Sensing & Instrumentation
Broadband Dielectric Spectroscopy is a powerful tool for investigating a variety of dielectric processes for both electrical and non-electrical applications. Also called Impedance Spectroscopy, the measurement separates molecular process on the basis of response time, providing a unique relaxation frequency along with a signature variation with frequency.
-
Product
Dielectric/Conductivity Sensor
Quarto-VariconTM
-
The Quarto-Varicon sensor is a thin, flexible dielectric sensor designed for cost-sensitive use with presses, molds, bulk materials or laminates. Patterned on a polyimide substrate, the Quarto-Varicon sensor can be supplied without leads, or with custom-length Teflon-insulated leads attached.
-
Product
Dielectric/Conductivity Sensor
Mini-VariconTM
-
The Mini-Varicon sensor is a thin, flexible dielectric sensor designed for cost-sensitive use with presses, molds, bulk materials or laminates. Patterned on a polyimide substrate, the electrode array is designed to allow a choice of high or low sensitivity, selected by either using the whole sensor or cutting off a portion of the array at a designated line. The Mini-Varicon sensor can be supplied without leads, or with custom-length Teflon-insulated leads attached.
-
Product
Dielectric Strength Tester
HY
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard GB/T 507 "Test Methods for Breakdown Voltage of Lubricating Oil". It can be widely used to determine dielectric constant of lubricating oils in the field of railway, aviation, power plant, petroleum industry, and scientific institutes.
-
Product
AC Dielectric Test Systems
700-DI
-
The HIPOTRONICS standard line of AC Dielectric Test Systems are designed to perform high voltage AC tests on electrical apparatus in accordance with IEC60, IEEE 4 and IEC 270 and other national test standards. A variety of mechanical configurations are available to suit different installation conditions. Some models can be supplied in mobile versions when it is difficult to move the test object to the test area. AC Dielectric Test Sets are available in a wide range of voltage and power ratings with exceptional reliability, durability and functionality. No matter what your requirement is, HIPOTRONICS has an affordably priced, highly reliable test solution to meet your needs.
-
Product
Software
Dielectric Constant
-
Materials Development Corporation
The Dielectric Constant option allows the user to measure the dielectric constant of a wide range of materials. Simply input a test voltage (in accumulation), the area (or diameter), and stray capacitance to determine the relative dielectric constant.
-
Product
Dielectric Strength Test Apparatus
CX-KD12
-
Shenzhen Chuangxin Instruments Co., Ltd.
To improve the insulation board and creepage dielectric properties, surface brushed polished, bottom bracket the minimum distance from the edge of >35mm, the altitude of 2000 meters designed to meet the strength test requirements of 12KV
-
Product
High Quality Transformer Oil Dielectric Strength Tester
AS-023A
-
Chongqing Assen Power Equipment Co., Ltd
AS-023A Series High Quality Intelligent Transformer Oil Dielectric Strength Tester is specially designed for testing dielectric strength (Breakdown Voltage) of transformer oil. The breakdown voltage (dielectric strength) is one of the most important parameters of transformer oil, it is a rule of the voltage withstand. The value of breakdown voltage (dielectric strength) indicates whether the oil contains water, impurity and electric particles, and you’ll know the oil value via the breakdown voltage (dielectric strength).
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
Pil Dielectric Test Sets
DTS Series
-
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
Product
SMART MEGOHMMETER
MD-1035e
-
The Megabras MD-1035e is a smart, microprocessor-controlled, 1 kV insulation tester. Besides the conventional measurement of insulation resistances up to 1 TΩ, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
Phase Stable Cables
FlatPhase 100 Series
-
Best in class phase stability vs. temperature makes FlatPhase™ the preferred option when you need flat phase.Our proprietary foamed fluoropolymer dielectric avoids the typical PTFE knee to deliver a flatter phase response.
-
Product
Handheld Moisture Meters
-
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
Product
SMART MEGOHMMETER
MD-5060x
-
The Megabras MD-5060x is a smart, microprocessor-controlled, 5 kV insulation tester. Besides the conventional measurement of insulation resistances up to 5 TΩ, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Programmable High Voltage Tester
-
The high Voltage also known as di-electric withstand tester comes with customized facilities like voltage rampup rate zero interlock, Plus the user may specify the voltage level and leakage milliampere level so as to suit its testing needs.
-
Product
Current Loop Supply Isolating Transmitter
Model TWS / TWS 2
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 °C ± 5 °C• Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
KV CAPS
200 V
-
Macom Technology Solutions Holdings Inc.
The MACOM KV CAPSTM Si high voltage capacitors feature very high working voltage ratings, very low loss and excellent stability by virtue of their novel internal construction and very high-quality dielectric layers. These capacitors are available as unpackaged chips. The chips have gold bonding surfaces on both terminals to enable excellent bonding and minimum contact resistance.
-
Product
TAN-DELTA AND RESISTIVITY TEST FOR INSULATING OIL
-
International Biological Laboratories
TDRNT02 measures dielectric parameters like D.C. resistivity, dielectric constant and loss factor of the insulating oil of transformers, circuit breakers etc.
-
Product
Hipot Tests
-
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
