Fuel Cell Stack
-
Product
High Precision Flame-proof Compression Type Load Cell
ZR-KE
-
Flame-proof Compression Type Load Cell
-
Product
PXI Mixed Configuration Relay Module - 9 Cells Populated
40-138-AA-BB-CC-DD (9 CELL)
Relay
The 40-138 2A Relay Module with 9 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
Voltammetry Cell
SVC-2
-
SVC-2 Voltammetry cell can be used for 4 modes voltammetry cell setup. Each voltammetry cell has its specific feature. However, SVC-2 can be sed in 4 modes. Also can apply as an oxygen-free voltammetry cell.
-
Product
Force Sensors, Load Cells, Shear Beam
-
INELTA Sensorsysteme GmbH & Co. KG
Exact force measurement and weight measurement
-
Product
Vacuum and Fuel Pump Tester
DVG1
-
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
Battery Cell Testing Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
The battery cycle life tester is a high-precisionsystem designed specifically for the battery cell charge and discharge testing.It is suitable for the battery cell cycle test, battery cell charge anddischarge aging test, battery cell performance test, battery cell capacitydetection test, battery cell IR test, deep-discharging test, function test ofhigh-power lithium-ion battery cells, such as EV battery module, ES batterymodule, super capacitor…
-
Product
Portable Engineered Test Cell
PET
-
PET is an innovative portable engine test cell. Most test cells are designed by an architect and built of conventional materials like bricks and mortar, making the cells immovable and inadaptable to changing requirements. Emprise has developed a practical alternative to this PET a portable and modular engine and component test cell.
-
Product
Dual Fuel Gauge
1U432-series
-
The 1U432 dual fuel gauge is packaged as a compact, 3” instrument. It has dual D’Arsonval movements that are driven by two resistive bulb transducers in the fuel tanks. The two opposing pointers stand out sharply from the non-reflective black background.
-
Product
TurboFan Test Cells
-
Atec, Inc. is an industry-preferred provider of full scale TurboFan test cell design, construction, maintenance, and refurbishment. Our seasoned aeroengine professionals and comprehensive network of international locations and resources provide our customers with unparalleled expertise and value for their most critical and complex test cell projects.
-
Product
Measurement Systems For Fuel Cycle, Safeguards And Decontamination & Decommissioning
-
Advancing critical radiation safety. Our technologies safeguard nuclear materials to protect people and the environment.
-
Product
Spectroelectrochemical Flow Cell
SEC-2F
-
Using the spectroelectrochemical flow cell, it is possible to have a different optical path length changing the gasket. We offer, as an optional item, a silicon and Teflon gasket with a 100, 250 and 500 m of the thickness. SEC-2F Spectroelectrochemical flow cell was designed to fit perfectly in the SEC2000 Spectrometer, and it eliminated the use of the optical fiber to connect the Spectrometer to the SEC-2F. Even for another brand of the spectrometer, you can connect the SEC-2F using the collimating lens and optical fiber.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Electronic Fuel Injection & Ignition Spark Tester Kit
36310
-
Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Contains Cat. No. 36300, Noid Light Set to test electronic fuel injection signals and the Cat. No. 23900, In-Line Ignition Spark Checker to trouble shoot the ignition system (Shows a duplicate view of the ignition spark). Supplied with Noid Lights to check Bosch PFI, Ford TBI, Geo TBI, GM PFI, GM SCPI and GM TBI.
-
Product
Trusted Platform Module Compliant With TCG 1.2 / 2.0 Specification And TCG Software Stack 1.2 / 2.0 Via LPC Connector On CPU Card.
PCA-TPM
Platform
TCG 1.2 / 2.0 specification and TCG software stack 1.2 / 2.0 via LPC connector on CPU card.Hardware based data protection solution for storage device encryption and decryption.Dimension: 31.5 x 30.5 mm
-
Product
Fatigue Rated Low Profile Cells
-
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
Product
Stack Gas Analysis System
ENDA-5000 series
-
Continuous simultaneous and high-precision measurement of NOx, SO2, CO, CO2 and O2.HORIBA has over 100,000 CEM systems installed and 30 years of quality and experience. That is the base on which HORIBA's new ENDA-5000 series of stack-gas analysis systems are built. These systems have a small footprint and use cross-flow modulated non-dispersive infrared (NDIR) and magneto-pneumatic detectors that are inherently drift-free. The ENDA-5000 series are superior continuous analysis systems that perform reliably for difficult exhaust gas measurements, when measurement errors cannot be tolerated. This CEM series features a new intuitive touch panel that makes every operation available with the touch of a single button. The ENDA-5000 series systems are also designed for ease of maintenance. They are ideal for a variety of uses, including emissions monitoring from steam boilers, refuse incinerators, and electric power generation plants to assure pollution standards are being met.
-
Product
POWERSTROKE FUEL INJECTOR TEST KIT
DFST20
-
*Tests Powerstroke engines from 1994 to current*Includes adapters necessary to pressure test the fuel system*Adapters can be used for testing at both the fuel filter and at the fuel pump
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Shear Beam Load Cell
SB-1.0
-
The Shear Beam Load Cell SB-1.0 is a single point weighing device, suitable for use in multiple applications.
-
Product
Semi-auto 4 Point Probe System for Solar Cell Substrate
RG-100PV
-
*Measurement system for thin film on substrate samples for multi-points measurement*Even pitch and random pitch for Max.1,000 points*2-D/3-D square mapping software for even pitch
-
-
Product
Load Cells
-
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
Product
12V based Power supply for PC104 and PC104p stacks
PC104pPWR12
-
The PC104pPWR12 power supply provides for the +5, +3.3, +12, minus 12 and minus 5 from a 12V wall mount transformer supply, battery etc. Each rail is fuse protected. The supply uses switching technology to provide high efficiency coupled with low pass filtering to provide low noise and fast response to transient loads
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Automotive Fuel Injector Pulser and Testing Tool
Wow
-
Automotive Diagnostics and Publishing
Developed to perform fuel injector flow testing, injector cleaning and pulse width general injector health determination, like pintle opening, binding and weak springs. But most of all, to perform accurate fuel flow tests using the pulser and your fuel gauge. The unit can handle all and any fuel injector in the industry. It can generate 5, 10 and 15 mSec or milli-second pulses and can also give you 1, 2, 4, 10 or continuous pulses.
-
Product
Charge-Discharge, Li-ion Cell Formation, and Test Solution
BT2200
-
The BT2200 charge-discharge platform is cost-effective and easily configurable for Li-Ion cell formation and lifetime cell cycling. A modular design supports cells requiring maximum currents ranging from ± 6 A to ± 800 A, with up to 256 cells or channels per chassis. You can quickly deploy different channel configurations as your cell requirements change and capacities grow.
-
Product
High Precision Compression Type Load Cell
IR
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
