Step Attenuators
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 0 to 11 dB, 1 dB steps
84904K
-
The Keysight 84904K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and attenuator range of 0 to 11 dB in 1-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Digital Control Step Attenuator
-
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
-
Product
Programmable Step Attenuator, DC to 50 GHz, 60 dB, 10 dB steps
84905M
-
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
Product
Programmable Step Attenuator DC~50GHz, 0~115dB Att.
-
The programmable step attenuator achieves step attenuation over a wide frequency band. It features high attenuation accuracy, excellent repeatability, low insertion loss, and long service life. Its primary applications include controlling the amplitude of signals entering systems, regulating output signal power in systems, and adjusting impedance matching between signal sources and loads. It is widely used in various broadband spectrum analyzers, broadband vector network analyzers, broadband synthesized signal sources, noise figure test sets, and diverse microwave automatic test systems.
-
Product
PXI Programmable Step Attenuator Module, DC to 26.5 GHz
M9168C
-
The M9168C is a programmable step attenuator module based on PXI hybrid platform. The M9168C operates from DC to 26.5 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
Step Attenuator
RSC
-
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
Product
Digitally Controlled Programmable Attenuators
-
Broadband frequencies ranging from 30 MHz to 40 GHz. High attenuation levels up to 60 dB. PIN diode designs exhibit extremely fast attenuation step switching performance. Attenuation step size ranges from 0.03 dB to 1 dB. Programmable attenuator control bit sizes range from 5 to 10 bits. Models powered and command controlled via 15 pin female Micro-D socket or USB interface.
-
Product
Digital Control Step Attenuator
-
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
Attenuation Control Unit, DC to 6 GHz, 0 to 121 dB, 1-dB Steps
J7201A
-
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
Product
Variable Optical Attenuator - MATRIQ
-
The VOA MATRIQ Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fibre types and various wavelengths to suit a wide range of applications.With a stackable, space-saving design and intuitive software controls make it a valued addition to the optical lab or test bench.
-
Product
Coaxial Fixed Attenuator, DC to 26.5 GHz
8493C
-
The Keysight 8493C coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator has APC-3.5 connectors and is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 40 dB.This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Coaxial Attenuators Set
11582A
-
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
SPL-03C-153 Step Probe
SPL-03C-153
-
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 50Test Center (mil): 125Full Travel (mil): 200Full Travel (mm): 5.08Recommended Travel (mil): 127Recommended Travel (mm): 3.23Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
Product
Coaxial Attenuators Set
11581A
-
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
-
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
Product
STP-1 Replaceable Step Probe
STP-1
-
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 135Full Travel (mm): 3.43Full Travel Remark: Varies with tip (min. 135 mil / 3,43 mm)Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1300Overall Length (mm): 33.03
-
Product
PXI Attenuator/Switch Driver Module
M9170A
-
The Keysight M9170A is a one-slot PXI attenuator switch driver module that provides the flexibility to drive Keysight's expansive portfolio of RF & microwave step attenuators and electromechanical switches. It is a PXI-hybrid compliant module that comes with a full-featured graphical interface soft front panel for easy control and trigger.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
41-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
43-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
Attenuator / Switch Driver
11713E
-
The 11713E attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
PXI Hybrid Amplifier/Attenuator
M9352A
-
The M9352A modules are custom built and tested to nominal* performance characteristics. Full regulatory and safety testing has been performed. This product has the same warranty and support services as other Keysight instruments. Because it is custom built, Keysight recommends checking availability and delivery information before ordering the product.
-
Product
Variable Optical Attenuator - PXI
VOA 1000 / 1100 / 1300 Series
-
The VOA Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fiber types and various wavelengths to suit a wide range of applications.With 1 or 2 channels in a single PXIe slot, it provides high channel density solution for easy integration in the versatile PXI platform.
-
Product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
41-182B-006
-
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI 5 Ch. Differential Hi Voltage Attenuator
41-661-001
-
High voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
PXI 10 Channel High Voltage Attenuator
41-660-001
-
The 41-660 and 41-661 are high voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
-
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Integrated Two Channel Variable Optical Attenuator with two Optical Power Meter Channels
N7752A
-
The Keysight N7752A combines an attenuator with 2 front-panel power meter channels, offering exceptional performance at a low price. The power meters permit measurements from any point in the measurements setup and assist in calibrating power offsets with respect to the attenuator output.
-
Product
Step Probes
-
*Precisely controlled probe travel*Step tip geometry*Replaceable and non-replaceable versions*Plating options available
-
Product
SPL-03C-090 Step Probe
SPL-03C-090
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 127Recommended Travel (mm): 3.22Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
