Step Attenuators
-
-
Product
PXI Dual RF Attenuator 63dB in 1 dB steps
41-180-022
-
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
SA1500X, 1.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784256-01
-
The SA1500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
-
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
Product
CP400X, 400 MHz, ±60 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
784254-01
-
The CP400X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 2 meters in length. The CP400X attaches to BNC connections on both the signal input and instrument sides.
-
Product
Variable Optical Attenuators
-
A fiber optic variable attenuator is used to reduce the power level of an optical signal in fiber optic communications.
-
-
Product
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV
RP4060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
RF Attenuators
-
Over 400 coaxial, surface mount, and MMIC attenuator models for 50-Ohm & 75- Ohm syetem including fixed attenuators, high-power attenuators, digital step / programmable attenuators, voltage variable attenuators and more. DC passing and DC blocking models. Power handling up to 100W. Bandwidths spanning DC to 50 GHz.
-
Product
Source - 20 GHz Source with Amp Attenuator
RI8554A
-
Automated Instruments, Powerful Development Tools and Worldwide Support
-
Product
Normalised Site Attenuation
NSA
-
Normalised Site Attenuation (NSA) is measured in accordance with CISPR 16-1-4 and ANSI C63.4 in semi and fully anechoic environment.
-
Product
Fixed Attenuator (Coaxial)
-
Coaxial attenuators in a variety of attenuaton values, power levels and connector types.
-
Product
Step Recovery Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
Product
SP200B, 200 MHz, ±60 V, 1X or 10X Attenuation, Single-Ended Passive Oscilloscope Probe
780284-01
-
The SP200B is a standard switchable passive probe for oscilloscopes that provide 1 MΩ input impedance. Depending on the attenuation ratio, the probe has an analog bandwidth of 6 MHz in the 1x attenuation setting or 200 MHz in the 10x attenuation setting.
-
Product
Fixed Attenuator (Waveguide)
-
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
Product
PXI Attenuator
-
Keysight offers step attenuator modules that operate across a broad frequency range of DC to50 GHz.
