Product

Lo-PRO®file Collet Socket with Wire Wrap Pins

Series 503

-

Aries

Series 503 - Aries

LO-PRO file Collet Sockets with Wire Wrap Pins. Features: LO-PRO file Collet Sockets are available with solder tail or wire wrap pins. Consult Data Sheet No. 12011 for solder tail pins. Choose from several sizes and plating options.

Product

Glow Wire Tester

-

Shanghai Dean Electrical Co., Ltd

Shanghai Dean Electrical Co., Ltd

Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.

Product

Mating Coax Connector With 20 Coax Pins Crimped (One End) To 5 Foot Wires

GX96404-60

-

Marvin Test Solutions, Inc.

GX96404-60 - Marvin Test Solutions, Inc.

Mating Coax Connector with 20 Coax Pins crimped (one end) to 5' wires. Coaxial cable: RG316, 50 ohms.

Product

J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m

745690-J001

-

NI

745690-J001 - NI

J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.

Product

Four Wire Modem for SEL Mirrored-Bits

MBT 9600

-

Ametek Power Instruments

MBT 9600 - Ametek Power Instruments

Application specific features set the MBT9600 Four Modem apart from the conventional high speed modems. Its compact size and ease of installation make the MBT9600 an ideal, low cost alternative to conventional audio tone teleprotection systems.The circuitry is ideally suited for use over private networks such as conventional voice channels over analog microwave.

Product

PCI-1240 Wiring Terminal, DIN-Rail Mount

ADAM-3952-AE

-

Advantech Co. Ltd.

ADAM-3952-AE - Advantech Co. Ltd.

PCI-1240 Wiring Terminal, DIN-rail Mount

Product

Minigrabber® Test Clip For Max. .090" Wire Dia, Do-It-Yourself

3925

-

Pomona Electronics

3925 - Pomona Electronics

Minigrabber? test clip for max. .090" wire dia, Do-It-Yourself, available in ten colors

Product

2.5mm Test Wire Test Probe Pin

CX-3C

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-3C - Shenzhen Chuangxin Instruments Co., Ltd.

2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.

Product

Automatic Wire Test Set

AWTS

-

Eclypse International

AWTS - Eclypse International

The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.

Product

Gauge Type T Thermocouple Wire

W-TW-36P2

-

Physitemp Instruments

W-TW-36P2 - Physitemp Instruments

Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.

Product

Gauge Type T Thermocouple Wire

W-TW-44P2

-

Physitemp Instruments

W-TW-44P2 - Physitemp Instruments

Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.

Product

15 Ft Cable, 78-Pin Female Connector On One End, Loose Wired (Numbered) Other End

GT97113

-

Marvin Test Solutions, Inc.

GT97113 - Marvin Test Solutions, Inc.

15' harness, 78-pin female D-sub connector on one end, loose wired (numbered) other end.

Product

Wire and cable slicer

CX-18

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-18 - Shenzhen Chuangxin Instruments Co., Ltd.

Wire and cable slicing machine is a kind of used products factory la bequipment. Using mechanical transmission feed, blade cutting structure, it can be cut1 to 12 mm range plastic various thickness, sheet material, etc., they are availablRubber, leather material and hardness of the material must be sliced, the machine is widelyUsed in rubber, plastic, leather, electric wire, cable, scientific research units, etc.

Product

Trailer Wiring Buddy 7 Pin Flat

222

-

Electronic Specialties Inc.

222 - Electronic Specialties Inc.

*Each signal from vehicle emits a unique tone *Electric brake control signal illuminates red LED *Loud beep can be heard over shop noise *Time Saver! Just apply brakes, right/left turn signals, running lights, engage reverse & 12 Volt Charging voltage *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!

Product

Wire Crimp Pull Sensor

Model MR06-200

-

Mark-10 Corp.

Model MR06-200 - Mark-10 Corp.

The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).

Product

Wire Harness Tester

Panther4HT Master- Slave DSU

-

Qmax Test Technologies Pvt. Ltd.

Panther4HT Master- Slave DSU - Qmax Test Technologies Pvt. Ltd.

The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.

Product

Datapaq® Furnace Tracker Systems

-

Fluke Process Instruments

Fluke Process Instruments

For metal heat treatment industries, measuring both product temperature and its environment is critical to ensure both product quality and process efficiency, which is why Fluke Process Instruments has designed the most robust, sophisticated furnace profiling systems. From data loggers and thermal barriers to intuitive software data analysis and reporting, we have everything users need to profile their process, no matter how challenging. The Datapaq Furnace Tracker System is designed to be used repeatedly, in-process in the most hostile manufacturing environments, while still providing accurate and reliable through-process temperature surveys. Each system can help users improve performance and system accuracy, decrease downtime, reduce TUS reporting times and more.

Product

J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 2 m

745690-J002

-

NI

745690-J002 - NI

J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.