Product

Electrical Resistance Probes

-

Metal Samples Company

Metal Samples Company

Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.

Product

Probes

-

NDS Products, Inc.

NDS Products, Inc.

Pancake, Side Wall and Window

Product

Temperature Probe

P0132

-

COMET SYSTEM, s.r.o.

P0132 - COMET SYSTEM, s.r.o.

Is designed for temperature measurements in stainless steel well.

Product

Capacitance Sensors

Accumeasure Series

-

MTI Instruments

Accumeasure Series - MTI Instruments

The Accumeasure product line features capacitive sensor products for high resolution gap and displacement measurements that require a high level of accuracy that is both stable and repeatable. A capacitive sensing system consists of a probe and amplifier. Capacitive measurements can be performed in a multitude of environments using non-contact passive capacitance probes that are not affected by magnet fields, temperature, humidity, nuclear radiation, and pressure. This is largely due to the nature of the rugged and passive capacitance probes.

Product

High Voltage Optically Isolated Probe, 700 MHz Bandwidth. Includes soft-carrying case.

DL07-ISO

-

Teledyne LeCroy

DL07-ISO - Teledyne LeCroy

The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.

Product

Standard - 6.00 (170.00) - 14.00 (397.00) Feed Through Probe

P2447-1W

-

ECT

P2447-1W - ECT

Current Rating (Amps): 20Average DC Resistance lower than (mOhm): 10Test Center (mil): 225Test Center (mm): 5.72Full Travel (mil): 300Full Travel (mm): 7.62Recommended Travel (mil): 200Recommended Travel (mm): 5.08Overall Length (mil): 1,145Overall Length (mm): 29.08

Product

Premium 4.49 (127.00) - 12.00 (340.00) High Performance Lead Free Probe

LFRE-25H-12

-

ECT

LFRE-25H-12 - ECT

Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Near Field Probes 30 MHz up to 3 GHz

RF2 set

-

Langer EMV-Technik GmbH

RF2 set - Langer EMV-Technik GmbH

The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.

Product

GL Products Online & Interactive Demos

-

GL Communications Inc.

GL Communications Inc.

*NetSurveyorWeb™ is a centralized VoIP network monitoring system. A number of GL's PacketScan™ probes and/or,PacketProbes™ are deployed in remote locations across the network to passively monitor VoIP traffic. Whenever a monitored call completes, the scan/probe calculates a variety of quality metrics (MOS, loss, delay, jitter, etc) and sends the metrics to the central Oracle database for storage.**The PacketScan™ is a feature-robust Windows® based software tool that captures and monitors live IP traffic. In the VoIP world, it can monitor and measure SIP, H323, Megaco, MGCP, T.38 and video calls. In addition to quality metricsPacketScan™ also captures signaling information and sends that to the NetSurveyorWeb™ database as well.**GL's PacketProbe™ is an advanced CPE(Customer Premises Equipment) based VoIP monitoring reporting and diagnostic appliance, stemming from GL's suite of market leading voice analysis tools.

Product

Standard Probe Station Chucks & Accessories

-

ABET Technologies, Inc.

ABET Technologies, Inc.

In this test solutions section of our website we describe the expanding line of Abet PV IV probe stations for the growing variety of solar cell types and sizes being developed around the world. This page describes a line of vacuum chucks and accessories for top/bottom, top/top, and bottom/bottom solar cells from 3 x 3 mm to 300 x 300 mm. Probe stations for multiple device on a single substrate and multifunction probe stations are described further in the sections highlighted to the left of this page.

Product

Tracing-Type Non-Contact Inspection System For LCD/STN/Touch Panel/FPC

TTS

-

OHT Inc.

TTS - OHT Inc.

*"Probe + Non-Contact Sensor" enables to delect SHORT after sticking LCD*No Fixture in LCD Inspection*Applicable to FPC Inspection

Product

Probe 0.5mm clip (orange)

PK106-3

-

Teledyne LeCroy

PK106-3 - Teledyne LeCroy

Probe 0.5mm clip (orange).

Product

Sensors, Probes And Coils For Component Testing

Sensors

-

Foerster Instruments, Incorporated

Sensors - Foerster Instruments, Incorporated

We offer a comprehensive range of standard and customised sensors, probes and coils for component testing. If the wide selection of standard sensors does not optimally solve your testing task, we offer you an individual new development specially adapted to your testing task. Thanks to our many years of experience, you receive reliable sensor technology for reproducible test results.

Product

Tackiness Tester

TAC1000

-

Rhesca Co., Ltd.

TAC1000 - Rhesca Co., Ltd.

For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.

Product

75% Satured Solution for RH Sensor

HD75

-

Senseca

HD75 - Senseca

75%RH saturated solution for checking the relative humidity sensor, complete with screw adaptor for probes ∅ 14mm, M12×1 thread.

Product

Field Probe for Electric & Magnetic Field Measurement

WP400-3

-

Wavecontrol, S.L.

WP400-3 - Wavecontrol, S.L.

Wavecontrol presents a new and unique field probe for the measurement of electric and magnetic fields that integrates both E & H sensors within dimensions of only 3 cm². Which makes it unique is that Wavecontrol has managed to add an E field sensor in a basic structure of a classical 3 cm² field probe. It has been possible, therefore, to obtain a 3 cm² field probe without compromising the capability of assessing E and H fields of its 100 cm² big sister, the recognized and successful WP400.

Product

Controlled Impedance Analyzers

-

Hyperlabs, Inc.

Hyperlabs, Inc.

HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.

Product

CO2 Concentration Transmitter

T5141

-

COMET SYSTEM, s.r.o.

T5141 - COMET SYSTEM, s.r.o.

CO2 concentration transmitter with 4-20mA output is built in a durable watertight case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off. The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.

Product

Gaussmeter

DX-102

-

Dexing Magnet Tech. Co., Ltd

DX-102 - Dexing Magnet Tech. Co., Ltd

DX-102 Gaussmeter is a portable gauss meter, based on the latest progress of Hall effect magnetic field measuring instrument, adopted DSP technology. Test probe adopts import GaAs linear Hall chip, the difference between any two probes is small, if damaged, it can be replaced directly. DX-102 Gaussmeter is an ideal DC magnetic field test instrument.