Surface Insulation Resistance Testing
testing check's PCB for shorts or current leakage between conductors.
-
Product
Force Testing
-
Force testing is a way of determining how an object will react when it is subjected to tensile or compressive loads
-
Product
HALT/HASS Testing
HALT HASS Chamber
-
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
Product
Test Contactor
MiCon
-
The MiCon™ Test Contactor is spring pin footprint compatible supporting advanced temperature requirements as well as advanced power/current requirements. The footprint compatibility allows for easy and cost-efficient conversion from spring pin setups. The fully decoupled load board side of the spring ensure no degradation of the load board pad.MiCon features a single piece design, which ensures a long lifespan, low and stable contact resistance, high current carrying capability and an extended temperature range. The MiCon allows for testing at full specification values. The extended operating range accommodates device lead trim and form variability such as device alignment accuracy and device lead coplanarity.
-
Product
Test Leads
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
Product
Electrometer / High Resistance Meter, 0.01fA
B2985B
-
The B2985B Electrometer/High Resistance Meter is the world’s only graphical electrometer that allows you to confidently measures small currents with 0.01 fA (0.01 x 10-15 A) resolution and large resistances of up to 10 PΩ (10 x 1015 Ω). It possesses a 4.3” color LCD with a graphical user interface that provides trend chart and histogram data in addition to numeric information.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS Basic
-
Optik Elektronik Gerätetechnik GmbH
Low cost contact angle meter provides all functions for DIN conform measurement of contact angle and SFE.
-
Product
Digital H.V. Insulation Tester(12kV)
7012 IN
-
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 20TΩ (20000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 24 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV ● AC/DC voltmeter (600V).● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : ● 1~30 minutes● Auto-off.● Calendar.● Optical USB to RS-232 data transmission.● 200 measurement results can be saved in the memory and recalled on the display.● Safety standard : EN 61010-1 CAT IV 600V EN 61010-2-030 EN 61326-1
-
Product
Resistance Meters
-
ACL provides surface resistance/resistivity meters and digital megohmmeters to quickly and accurately measure resistivity.
-
Product
Analogue (1kV below) Insulation Tester
1180 IN
-
Standard Electric Works Co., Ltd
High quality Taut Band movement. Battery operated. Solid state circuitry. Battery check feature. Automatic circuit discharge. Three insulation test voltages(DC) : 250V, 500V, 1000V. Continuity test : 50 Ω. AC voltage measurement : 500V. Color-coded scale. Fuse protected.
-
Product
Testing Services
-
Howland & Lawrence Chamber Services
RF shield testing: IEEE-299, MIL-STD-285, NSA 65-6CTIA CATL certification testing: Probe symmetry and amplitude ripple measurements following Test Plan for Wireless Device Over-the-Air PerformanceAnechoic material test, inspection, remediation: VSWR, inverse spherical nearfield testing of installed material and NRL arch screening tests of individual absorber pieces We can also provide in-process testing of welded steel shielded enclosures with a test technique based on ASME BPVC vacuum box testing—confirm quality of RF welds before the shield envelope is complete. We developed this method for testing the Navy’s Advanced System Integration Lab (ASIL) chamber at Patuxent River, shaving weeks off the construction/testing schedule.
-
Product
Surface Area and Porosity Analyzer
ASAP 2460
-
The ASAP 2460 Surface Area and Porosity Analyzer incorporates a unique expandable system designed for high-performance and high sample throughput. The base ASAP 2460 is a two-port master control unit. For more throughput, additional two-port units can be connected to the master unit expanding the system to either a four-port or six-port analyzer. The instrument also includes intuitive MicroActive software that combines user-defined reports with the ability to interactively evaluate isotherm
-
Product
Environmental Testing
-
We have a CTS C-65/100 Climatic Test Chamber available for hire at dB Technology.They have available:*Internal dimensions: 500 x 500 x 400mm (w x h x d)*Temperature range: -65°C to +180°C*Heating rate: 3°C/min*Cooling rate: 2°C/min*Climatic temp range: +10°C to +95°C*Humidity Range: 10 to 98% RH
-
Product
Flying Probe Test Programming & Testing Services
-
Zero Defects International LLC
ZDI utilizes a Seica flying probe tester in order to provide test program development and testing services to customers in Silicon Valley and throughout North America. This is a very cost-effective solution for printed circuit assembly manufacturers who do not have in-house equipment of their own but have customers who require test services.
-
Product
Polysilicon Resistivity Tester
HS-POSRT
-
HS-POSRT polysilicon resistivity tester is an advanced resistivity tester, it has features of wide resistivity measuring range, high testing accuracy, high stability, swift body and easy operation. It is a good friend to Siemens polysilicon material producer,SH4 polysilicon material producer, UMG polysilicon material poroducer and so on
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
Pre-compliance Testing
-
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
Product
Performance Testing
-
LOAD TESTINGEvaluates software behavior under a specific expected loadVOLUME TESTINGEvaluates software productivity under an increasing volume of stored and processed dataSTABILITY TESTINGDetermines the effect of configuration changes on the system's performance and behaviorSTRESS TESTINGIdentifies the upper limits of software capacitySCALABILITY TESTINGMeasures software capability under increased processing power and architecture changesCONFIGURATION TESTINGDetermines the effect of configuration changes on the system's performance and behavior
-
Product
Surface Roughness Tester
-
A precision instrument used to evaluate the texture of a surface, determining whether it is rough or smooth.
-
Product
The Complete Solution for Optical Surface Quality Inspection
OptiLux SD (Scratch-Dig)
-
RedLux’s OptiLux SD system provides the complete solution for control of optical surface quality (scratch-dig) by offering a breakthrough in measurement performance along with conformity to industry standards. Designed with flexibility in mind and further enhanced by a range of customer inspired features, the OptiLux SD can support the most demanding of optical surface quality inspection processes, from highly customized optical components in low volume, to standard components in high volume.
-
Product
Test Services
-
D-Coax offers RF/Microwave test services for your researchprojects, as well as, production quantities tests. We have available resources and expertise in the high frequency interconnects testing that will benefit your research and products. We will work with you to make your requested tests the most accurate and reliable and we'll complete them in a timely fashion. The following parameters can be characterized or tested to specifications with our test services: Time Domain: Impedance, Impedance profile, rise time, propagation delay, skew and more. Frequency Domain: S21 - Insertion loss, S11- Return loss, S12 - Reverse Insertion loss (port 2 insertion loss), S22 - Reverse Return loss (port 2 return loss) and more.
-
Product
High Insulation Digital Clamp Tester
HCL-3000D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide AC current measurements for 0.001A～20A.*Easy operation, Push to Open and Pull to Disconnect Mechanism.*Safe AC current measurements for high voltage circuit (AC80 to 7000V).
-
Product
Contact Resistance Test Sets
-
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
-
Product
Water Cooled Active Resistance DC Electronic Load
WRx Series
-
Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.
-
Product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
-
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
Product
Efficiency Test
-
Type test stands for industrial electric motors*Testing of 1-phase and 3-phase asynchronous and synchronous motors up to 3 kW*Speeds up to 30000 1 / min
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Insulation & Multifunction Tester (LCD Display)
4175 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Telecommunication test voltage : 50V and 100V.● Large range of insulation test voltages: 50, 100, 125, 250, 500, 1000V.● Mov / protection devices test.● Gas Arrester function.● Automatic voltmeter AC/DC at Start/Reset.● Test ON-OFF.● Battery test.● Safety voltmeter before each test.● Auto-discharge on all test and all ranges.● Battery test at Switch ON-TEST.● Smart hold & Stop on voltmeter AC/DC.● eads AUTO-NULL Key.● Test Auto-stop.● Auto range.● Ener-Save™.
-
-
Product
Test SIP
-
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
