Safety Compliance
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
EMC Compliance Test Systems
ECTS2
-
Now in its second generation, the ADAPTIVE POWER EMC Compliance Test Systems use a greatly enhanced harmonics and flicker measurement system and newly designed flicker impedance options to support single and three phase AC harmonics, flicker and AC and DC immunity compliance testing up to the maximum required current of 75A per phase.
-
Product
Compliance and Data Protection
-
Locate and protect sensitive and PII data to identify risk and ensure compliance. Monitor system events to identify and proactively respond to potential risks and bad actors. Simplify security operations, reduce risk and lighten security management load with automated ID and authorization cleanup.
-
Product
Consumer Safety and RoHS Handheld XRF Analyzer
-
DELTA Consumer Safety & RoHS Handheld XRF Analyzers allow for testing large quantities of consumer & electronic products anywhere, anytime. Get simple, fast, nondestructive regulatory compliance screening for Pb, Cd, Hg, Br & more. Use for ASTM Method F2617-08, HR4040, CPSC, CPSIA & more.
-
Product
Installation Safety Testers
VDE 0100
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
-
Product
Safety Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide range of Safety Relays for a variety of applications such as Emergency Stop Switches, Safety Control Units, Elevator Control, Escalator Control, and Industrial Automation, Machine Tool, Robots, Safety PLCs and more. Force guided contacts according to EN50205 Class A.
-
Product
Compact & Robust Safety Light Curtain [Type 4 PLe SIL3]
SF4D
-
Panasonic Industrial Devices Sales Company of America
Panasonic's SF4D Series Safety Light Curtains have a slim, yet robust unit body that resists twisting, warping and impact.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Safety Test Panel for Geyser
-
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
Product
Safety Certified I/O Modules
HY-TTC 30XSH
-
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
Product
EMI and EMC Compliance Testing
-
Compatible Electronics has evolved into one of the biggest and most experienced testing and consulting companies in California. All this experience has made us keenly aware of your EMC/EMI needs.
-
Product
3D Compliance SAR System
cSAR3D
-
Schmid & Partner Engineering AG
cSAR3D is our newest and most advanced system for fast, high-precision SAR measurements of wireless devices. We have realized a system concept that has been developed over the last years to meet the demands of our highly valued customers. The system uses a novel sensor concept and advanced reconstruction algorithms. The measurement system has high absolute accuracy due to the determination of all field components in a large region of the head and body phantoms.
-
Product
Safety Control Unit
Epec SC52
-
SC52 offers a flexible solution for software-based safety function implementation. Together with the SC52 controller, Epec offers a set of pre-certified PLCopen application libraries in order to reduce customer’s safety related software development effort.
-
Product
Safety Locking Devices
-
Leuze electronic GmbH + Co. KG
Safety switches with locking device keep doors locked and thus prevent unauthorized entry or access, thereby protecting persons and processes. The L series features a wide range of variants for different application cases, from devices with mechanical actuators to devices with an RFID‑coded actuator for maximum manipulation protection as well as integrated command buttons. With their robust design, all devices are designed for rough industrial applications.
-
Product
Safety Shoe Electrical Resistance Tester
UI-FT06
-
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Safety Relay
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
-
-
Product
Safety Door Switch with Key
SG-B2 Series
-
Panasonic Industrial Devices Sales Company of America
These products feature key-based operation for worker protection in larger areas that could be hazardous. The SG-B2 Series Safety Door Switch and the SG-D1 Series Key Selector Switch can be used in tandem to add multiple layers of protection.
-
Product
Automotive Ethernet Rx Compliance Software
AE6910R
-
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Software Development Standards Compliance Solution
-
The most comprehensive development compliance solution; FDA, DO-178B/C, MISRA, JSF, PCI-DSS, ISO, IEC, and more. ntegrate compliance policies into the SDLC and team workflow. Accurately and consistently automate verification and validation tasks
-
Product
Electronic Safety Sensors
-
Non-contact, RFID-based devices designed to monitor movable guards like doors, panels, and hoods in industrial machinery.
-
Product
Electric Safety
PV-ISOTEST
-
PV-ISOTEST represents a real innovation in the panorama of PV verification and testing instrumentation. PV-ISOTEST measures the insulation resistance of a single module, a string or even an entire photovoltaic field up to 1,500 V DC according to IEC/EN62446 standard.
-
Product
Ultra-Slim Safety Door Switch with Solenoid Interlock
SG-B1 Series
-
Panasonic Industrial Devices Sales Company of America
The SG-B1 Series and the SG-A1 Series are among the world’s thinnest Safety Door Switches. The SG-B1 Series features a solenoid interlock and five built-in contacts. The SG-A1 Series Safety Door Switch comes with three built-in contacts.
-
Product
PCI Compliance Testing
-
The Payment Card Industry Data Security Standard (PCI Standard) defines merchant requirements for securing cardholder information. This worldwide standard for consumer data protection across the payment industry was developed to counteract the rising number of incidents of stolen cardholder account data.?
-
Product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
